Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Denton, TX
Carver Gate Repair is the gate company Denton homeowners call when a swing gate sags, a slide gate jams on its track, or a motor stops responding. We work exclusively on gates and gate automation across Denton, from the older ranch-style lots near the University of North Texas to newer subdivisions east of I-35. Every job gets a written price before any work begins, so the number on the invoice matches the number you approved. Call (469) 530-2485 and you’ll reach a live person, not a voicemail queue.
Why Denton Homes Are Different
Denton’s housing stock runs from 1960s brick ranches scattered south of University Drive to master-planned communities with alley-loaded garages and ornamental steel driveway gates. That spread matters. A gate hung on a 40-year-old brick column in the Idiot’s Hill area often has wood rot inside the post or a foundation that has shifted subtly over decades of north Texas clay movement. Newer builds in neighborhoods like Robson Ranch tend to have better column footing but more complex automation: keypads, vehicle loop detectors, and remote receivers wired into HOA-managed roads.
The local soil is a genuine factor. Denton sits on expansive clay that swells after spring rain and contracts through late summer. Gate posts set without deep concrete or proper drainage drift out of plumb a degree or two every season. That misalignment wears down hinges, bends tracks, and eventually trips the motor’s limit switch. It’s the most common root cause we find on repair calls across Denton, and it’s why we treat a gate repair here as a full-system check rather than a quick part swap.
Our Main Denton Services
Most Denton calls start with one of two problems: a gate that won’t open reliably, or a motor that runs but doesn’t move the gate. Below are the three services we provide, each with its own Denton page.
Gate Repair in Denton
A gate that scrapes the ground, pulls away from its hinges, or stops halfway through its travel arc is a repair job. In Denton, we see a lot of hill-side lots where the gate was built level but the ground has since settled, leaving a low corner that catches. We align and reinforce the frame, replace worn hinges and rollers, and true up the operator arm if one is installed. The work ends with a written guarantee good for a full year. Full details are on the Gate Repair in Denton page.
Gate Installation in Denton
New gate installation in Denton usually means setting posts deep enough to hold against expanding clay, then hanging a gate rated for the opening’s width and weight. We measure every opening before quoting, and the quoted price includes hardware, labor, and cleanup. Many Denton HOAs require a specific gate style or finish, so we work from your HOA’s design standards when they exist. See the Gate Installation in Denton page for what’s included.
Gate Motor Repair in Denton
When a gate motor hums but doesn’t move, or trips its breaker every cycle, the issue is usually electrical or mechanical inside the operator. In Denton, lightning strikes and power surges after summer storms are a recurring cause of fried control boards. We test the capacitor, limit switches, and wiring, then replace only what has failed. We stock parts for FAAC, BFT, and LiftMaster operators locally, which keeps most repairs to one visit. Full scope and typical costs are on the Gate Motor Repair in Denton page.
What happens when you call
- 1
A real person answersNo phone trees – you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Denton
We service gate motors and operators from FAAC, BFT, Linear, and Viking, among others. Common parts for these systems are stocked in our metro Dallas-Fort Worth parts bench, so a Denton repair rarely waits on a ground shipment. See our brands for the full list of systems we support.
Pricing for Gate Company in Denton, TX
| Service | Typical range in Denton |
|---|---|
| Gate repair service call | $75 – $125 |
| Hinge replacement (pair) | $150 – $400 |
| Track alignment for slide gates | $200 – $500 |
| New gate installation (basic) | $1,200 – $4,000 |
| Custom driveway gate installation | $3,500 – $10,000+ |
| Swing gate motor replacement | $600 – $1,800 |
| Slide gate motor replacement | $850 – $2,500 |
| Control board repair or replacement | $250 – $900 |
| Keypad or loop detector installation | $250 – $750 |
| Remote transmitter programming | $50 – $150 |
What pushes a Denton price higher is usually the clay. Posts that have drifted out of plumb need to be reset, not just shimmed. A motor that has run against a misaligned track for months may need both a new track and a new operator arm. Whatever the total, you approve a written quote before any work starts, and the price doesn’t move after that.
Neighborhoods We Serve in Denton
We run calls across all of Denton, from the streets around the university to the rural-acreage lots on the city’s west edge. Response time is typically same-day for repair calls placed before mid-afternoon.
- Robson Ranch
- Southridge
- Idiot’s Hill
- Rayzor Ranch
- Forestridge
Service Area – Cities Near Denton
Our Denton crews also take calls in the smaller towns that ring the city. If your gate is down in Krum, TX, Argyle, TX, Sanger, TX, or Aubrey, TX, we’ll send the same background-checked technician with the same written-price policy.
Serving Denton, TX – Our Local Coverage Area
We’re based in the Denton area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Denton
Most repair calls in Denton are handled the same day if we’re called before mid-afternoon. Emergency calls are answered live 24/7 by a person at (469) 530-2485, and we’ll give you a straight answer about when a technician will arrive.
For most standalone driveway gate installations, no city permit is required. If the gate is part of a larger fencing project or HOA-governed community, your HOA’s design standards may require submission. We’ll flag that before you’re quoted so there are no surprises.
Yes. We run calls to acreage properties west and north of the city, where slides and ranch-style gates are common. If you’re inside the broader Denton area, call us and we’ll confirm coverage for your street.
If your gate is sagging, stuck, or silent when you press the remote, call Carver Gate Repair at (469) 530-2485. A live person will answer, and you’ll get a written price before any work begins.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Denton Customers Say
"Gate hinge was bending under the weight. Welded a new bracket on and re-hung it. Solid now."
- Rudy A."Slide gate wasn't opening fully. Veteran tech found a worn drive chain and a misaligned limit. Fixed both in one visit."
- Don H."Good repair on a motor board. Waited a few days on the part, but they stayed in contact."
- Shelby T.