Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Delray Beach
A new gate installation in Delray Beach typically runs $2,800 – $9,500 depending on the gate type, operator, and how close your property sits to the Intracoastal. Coastal properties need a different material spec than homes west of I-95, and we price accordingly with a written quote before any work begins. Our crews know Marine Way, Gleason Street, and the communities off Linton Boulevard because we work them every week. Call (469) 530-2485 for a free measure and a written price, usually within one business day.
Why Carver Gate Repair Is Delray Beach’s Preferred Gate Installation Company
Delray Beach homeowners call us because the gate industry here has a specific problem: too many installers quote inland-grade steel near the coast and walk away before the rust shows. We do not do that. Our Gate Installation team writes the material spec into the quote, including fastener grade and coating, so you can compare what you are actually buying. Lonnie Burke runs our operation with one rule: if the spec will not survive three seasons of salt air within a mile of the water, it does not go on the truck.
We answer the phone. A live person picks up 24 hours a day, every day, because a gate that will not close at 11 p.m. is not a Monday problem. We dispatch uniformed, background-checked technicians to Delray Beach, and each one carries the same written-price policy: the number on the quote is the number on the invoice, agreed before the first tool comes out.
Every installation carries the 365-Day Done Right Promise. If something fails inside a year, we return and fix it at no charge, no argument. That guarantee is in writing, not spoken over a handshake. For Delray Beach properties near the salt-aerosol zone, that year of coverage tells you whether the coastal-grade materials are doing their job. They will be.
Gate Fabrication in Delray Beach
Gate Fabrication in Delray Beach means building a gate to a specific width, height, and coastal material spec rather than pulling a stock unit from a catalog. Most of the work we do within two miles of the Intracoastal, including the neighborhoods around George Bush Boulevard and the streets off A1A, is custom-fabricated because the salt exposure demands it. A fabricated steel or aluminum gate in Delray Beach runs $1,800 – $5,500 for the gate alone, before operator and installation.
Coastal Material Requirements
Near the water, hot-dip galvanized steel frames with 316 stainless fasteners are the floor, not an upgrade. Painted mild steel with zinc-plated bolts will show rust bloom at the hinge post and weld points within 12 – 18 months. We specify the galvanizing thickness and fastener grade in writing on every Delray Beach fabrication quote.
When Fabrication Beats Off-the-Shelf
Driveway openings in older Delray Beach neighborhoods are rarely a standard width. Tree roots, paver driveways, and angled property lines mean a stock 12-foot gate does not fit. We measure, build, and install to the actual opening, including gates for odd slopes and curved approaches.
Automatic Gate Installation in Delray Beach
Automatic Gate Installation in Delray Beach pairs a new or existing gate with a motorized operator, safety sensors, and access controls. A complete automatic driveway gate system in Delray Beach runs $3,500 – $9,500 installed, with the spread driven by operator type, gate weight, and whether we are running new conduit for power. The barrier island and coastal ridge add one more variable: salt-laden humidity attacking boards and connectors.
Operator Selection for Coastal Air
We install operators from brands that hold up in humid, salt-heavy conditions. FAAC and BFT hydraulic and electromechanical units have proven service records in Delray Beach, and we stock replacement boards and limit switches locally so a corrosion failure does not mean waiting on a backordered part. Linear and Viking operators go into inland Delray Beach properties where the exposure is lower and the budget is tighter.
Safety Electrical and Sensors
Florida code and plain common sense require photocells and edge sensors on automatic gates. On a Delray Beach install, we use sealed sensor housings and weather-rated connectors because salt corrosion on an unprotected photocell wiring joint produces ghost faults: the gate stops, reverses, or refuses to close for no visible reason. We replace that failure mode before it starts.
Trusted Brands We Service in Delray Beach
We train on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule equipment. For Delray Beach customers, that matters in a specific way: when a FAAC board corrodes or a BFT limit switch fails, we are not calling a distributor and hoping. Our technicians carry the common parts for Delray Beach’s installed base, so repair and replacement work happens in one visit, not three.
Common Gate Installation Problems We See in Delray Beach Homes
- Hinge post corrosion. Salt aerosol attacks the weld and base of the hinge post long before the gate panel looks bad. A sag correction without replacing the post will re-fail in one season.
- Operator board degradation. LiftMaster and BFT boards exposed to coastal humidity develop intermittent faults and ghost openings. The fix is a sealed enclosure and a corrosion-resistant board coating, not just a board swap.
- Galvanic corrosion at fasteners. Mixing stainless fasteners with a painted mild-steel frame concentrates rust at every bolt hole. On the coast, the entire fastener set must match the frame material.
- Wrong post footings for sandy soil. Coastal Delray Beach lots often sit on sand with a high water table. A standard concrete pour spalls and shifts; we use a marine-grade mix and deeper footings on beachside installs.
Pricing for Gate Installation in Delray Beach, FL
Here are the ranges we quote in Delray Beach. A single pedestrian gate: $900 – $2,200. A sliding driveway gate with a LiftMaster operator: $3,800 – $7,500. A double swing gate with an FAAC hydraulic operator: $4,500 – $9,500. Coastal-grade materials add 15 – 30% to the gate and hardware line items, and we show that as a separate figure on the quote so you see exactly what you are paying for. The written price is agreed before work starts. It does not move at the door. Call (469) 530-2485 for a free estimate.
We Also Serve Cities Near Delray Beach
Our crews cover Delray Beach and the surrounding South Florida communities, including Boynton Beach, Boca Raton, Deerfield Beach, and Greenacres. The same written-price policy and the same coastal material standards apply whether the job is on A1A in Delray Beach or inland in Greenacres.
Serving Delray Beach, FL – Our Local Coverage Area
We’re based in the Delray Beach area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Installation in Delray Beach
Salt air within a few blocks of the Intracoastal accelerates corrosion on gate hardware and operator boards by three to five times compared to inland locations. A gate that lasts five to seven years three miles west of the water may need a post replacement or board swap in two years on the barrier island. The fix is material selection, not more maintenance: hot-dip galvanized frames, 316 stainless fasteners, and sealed operator enclosures. Call (469) 530-2485 and ask for a coastal material spec on your quote.
A hot-dip galvanized steel frame with 316 stainless fasteners and a powder-coated aluminum gate panel is the longest-lasting combination for Delray Beach’s salt-aerosol zone. Avoid painted mild steel near the water, and avoid mixing fastener materials, which creates galvanic corrosion at every bolt hole. For slide gates, specify a stainless roller track and guides. Estimates are free, and we will write the exact material callouts on the quote.
Yes, in most cases we can install a LiftMaster or FAAC operator on an existing gate, provided the gate structure and hinge posts are sound. Near the beach, we inspect the post footings and frame welds before quoting an operator install, because a corroded post will compromise the operator within a season. If the gate is shot, we will tell you and show you the numbers for a new coastal-grade gate. Call (469) 530-2485 for a free inspection.
Salt-laden humidity attacks the circuit board and terminal connections inside the operator housing. The standard fix is a sealed enclosure with a coated board, dielectric grease on terminals, and weather-rated conduit connections. We have replaced enough corroded LiftMaster and BFT boards in Delray Beach to know that a bare board replacement without sealing the enclosure fails again within a year or two.
Yes. Automatic gates in Florida require safety photocells and, on most driveway systems, contact edge sensors to prevent entrapment. We install sealed, weather-rated sensors on every Delray Beach job and test them before we leave. The sensors are part of the written quote, not an add-on surprise. Call (469) 530-2485 to schedule a free measure.
Written by Lonnie Burke, Owner at Carver Gate Repair, serving Delray Beach and South Florida.