Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Texas City
A new driveway or security gate in Texas City typically runs $2,800 to $9,500 installed, depending on gate type, operator, and the groundworks your property needs. Most installations take 2 to 5 days from measure to final test, not same-day, because a gate set on undersized footings in this soil will sag within a season. We schedule a free on-site measure, give you a written price before any work starts, and we don’t move that number at the door. Call (469) 530-2485 to set up a measure. Our Gate Installation team handles everything from the post holes to the final safety reversal test.
Why Carver Gate Repair Is Texas City’s Preferred Gate Installation Company
Texas City homeowners call us because we show up and because the price we quote is the price we leave with. Every installation includes a written quote delivered before we put a shovel in the ground. If the number needs to change, you hear about it before the work continues, not after the gate is hanging. Lonnie Burke runs the operation, and the standard is simple: a uniformed, background-checked technician on site, a clean job site at the end of the day, and a gate that cycles properly for years.
Our crews coordinate dispatch from the Houston area and serve Texas City residents directly. You don’t get routed through a national call center. A live person answers the phone 24/7, including weekends and holidays. When you call about a new gate on a Saturday afternoon, someone picks up and schedules the measure. That matters here, where most gate installers treat Texas City as an edge of their service map instead of a place they actually know.
Gate Fabrication in Texas City
Gate fabrication in Texas City means building a gate to the exact dimensions of your opening and the specific conditions of your property rather than ordering a one-size-fits-all panel and hoping it fits. Most gates we install here are fabricated to order in steel or aluminum, then set on posts sized for coastal soil. A fabricated single swing gate in aluminum runs $1,800 to $4,200. Steel runs $2,600 to $5,800. Double gates run $4,500 to $9,500. Those prices include the gate, posts, and hardware, installed.
Driveway and Double Gates
Driveway gates are the ones we see most in Texas City, and double gates are common on wider driveways where a single gate would need too much sweep room or put too much load on one post. A double gate splits the load, but it doubles the hinge points, which is why each post gets its own footing and the gate leaves are set with a slight gap at the center for expansion. In this humidity, aluminum is often the better call than steel because it doesn’t rust at the welds.
Pedestrian and Security Gates
A pedestrian gate next to a driveway swing operator is a separate job from the driveway gate itself. We fabricate these to match the driveway gate’s style and height, usually 4 to 6 feet for residential security. In Texas City, we see a lot of pedestrian gates serving backyard access where the fence faces a drainage channel or open lot. Those gates need corrosion-resistant hardware at the hinges and latch, not big-box zinc hardware that seizes within a year.
Automatic Gate Installation in Texas City
Automatic Gate Installation in Texas City adds an operator, safety devices, and either line-voltage or solar power to a fabricated gate, and it typically runs $2,200 to $5,500 on top of the gate itself. The operator is matched to the gate’s weight and cycle frequency, not picked off a shelf. We install and program operators from Viking, Ghost Controls, DoorKing, and Elite, and every install includes photo-eye and edge sensor testing under UL 325 before we call the job done.
Swing Gate Operators
A swing gate operator in Texas City needs to be sized for the gate’s length and weight, and the arm type matters. Articulating arms handle wider gates and uneven ground better than linear rams. We set the operator on its own pad or post, run the control wiring in sealed conduit, and adjust the open and close limits so the gate doesn’t slam or stall. Coastal humidity kills cheap limit switches fast, so we use sealed components and dielectric grease on every splice.
Sliding Gate Operators
Sliding gates make sense on properties where a swing gate would need too much driveway depth or would block the street when opening. The gate rides on a track or a cantilever system, and the operator drives a rack gear or chain. In Texas City, we bed the track on compacted limestone and grade the area so storm water drains away from the rail and the motor. A gate that sits in standing water after a heavy rain is a gate that goes down fast.
Trusted Brands We Service in Texas City
We work on operators from Viking, Ghost Controls, DoorKing, and Elite, which covers most of what’s already installed on Texas City driveways and what we recommend for new installs. Every brand has its own programming sequence and its own weak points. A Ghost Controls opener on solar power behaves differently than a Viking running on line voltage, and we stock parts and boards for both. That means when your operator fails two years from now, we don’t tell you to call someone else because we don’t recognize the equipment. We fix it, and the repair is covered under the same 365-Day Done Right Promise that comes with every installation.
Common Gate Installation Problems We See in Texas City Homes
- Undersized post footings. In Texas City, a standard 24-inch footing often isn’t enough. Our coastal, high-water-table soil stays saturated, and a post set shallow will tilt and pull the gate’s alignment out of square, usually within the first year or two. We dig footings to 42 to 48 inches and use wider concrete bells at the base of the post.
- Photocells corroded by salt air. Cheap photo-eyes installed without sealed connectors oxidize quickly near the bay, and a gate that doesn’t reverse when a child or car is in the path becomes a serious safety problem. We use sealed photocells rated for exterior coastal exposure and test reversal force on every install, not just once, but on both open and close cycles.
- Loop detector splices that fail intermittently. In storm season, salt air and driving rain get into splices made without weatherproof junction boxes, and the gate starts opening or closing without a vehicle present. We run loop wiring in conduit and seal every splice with potting compound, then test the detector’s sensitivity on the vehicle’s actual approach angle.
- Operators installed without a power plan. Some Texas City properties have the panel on the far side of the house from the gate, and running power the wrong way creates voltage drop that burns out control boards. We run a dedicated circuit with properly sized wire, or we size a solar kit with enough battery reserve to run through cloudy stretches. Either way, the power plan is in the written quote, not a surprise line item later.
Pricing for Gate Installation in Texas City, TX
We Also Serve Cities Near Texas City
Our gate installation crews cover the whole Texas City area, including La Marque, Hitchcock, Dickinson, and Bacliff. If you live outside the city limits but still call this area home, the same written pricing and same guarantee apply. We coordinate dispatch for all of these communities through the same live-answer phone line, so whether you’re inside Texas City or just outside it, the process is the same.
Serving Texas City, TX – Our Local Coverage Area
We’re based in the Texas City area and offer Gate Repair – Texas City, so we know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Installation in Texas City
For a gate post in Texas City, the footing needs to go 42 to 48 inches deep with a wider concrete bell at the bottom, not the standard 24 to 30 inches. The high water table and moisture-heavy soil here shifts and settles, and a shallow post will tilt within a season or two and drag the gate out of alignment. We dig and pour footings to that depth on every installation, and we include it in the written quote as a line item rather than treating it as optional. Call (469) 530-2485 and we’ll explain what your specific driveway needs.
Yes, every automatic gate in Texas City needs working photo-eyes or edge sensors under UL 325, and we install and test both on every job. The coastal humidity here corrodes cheap photocells quickly, so we use sealed exterior-rated units and weatherproof the wiring connections. We run a full reversal test on both the open and close cycle before we leave. If your existing gate never had these installed or they stopped working, that’s a safety problem we can fix with the installation.
We install and service Viking, Ghost Controls, DoorKing, and Elite operators in Texas City, and we stock parts and boards for each. The brand matters less than matching the operator to your gate’s weight and cycle count, which we calculate at the on-site measure. A heavier steel double gate needs a different operator than a light aluminum pedestrian gate, and we don’t oversell you an operator you don’t need. Call (469) 530-2485 for a written quote on the right unit for your gate.
Yes, a new gate installation in Texas City can run entirely on solar power, and we install solar packages from Ghost Controls and Viking that include panels, batteries, and a charge controller sized for your gate’s cycle count. The Gulf Coast gets strong sun, but storm season brings stretches of cloud, so we spec battery reserve to cover several days without full sun. Solar adds $1,600 to $2,900 to the install, depending on the operator and battery bank needed. Call (469) 530-2485 and we’ll size a package for your gate.
A typical gate installation in Texas City takes 2 to 5 days from the start of work, depending on the gate type, the operator, and how much groundworks the soil requires. We do not promise same-day installation because setting posts correctly in this soil means letting the concrete cure before hanging the gate on it. The schedule is laid out in your written quote, and we stick to it. Call (469) 530-2485 and we’ll give you a realistic timeline for your specific gate.
Call Carver Gate Repair for Gate Installation in Texas City, TX
When you’re ready for a gate that’s built for Texas City soils and set on footings that won’t shift, call Carver Gate Repair at (469) 530-2485. We’ll schedule a free on-site measure, give you a written price before any work starts, and install your gate with a written guarantee that covers a full year. Lonnie Burke runs the operation to The Garrison Standard, and the crew that shows up at your gate is background-checked and uniformed. The number won’t move at the door. Call us today to get on the schedule.
Written by Lonnie Burke, Owner at Carver Gate Repair, serving Texas City, TX through the Garrison Partners family since 2008.