Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Campbell
Gate repair in Campbell usually means one of three things: a swing gate dragging on the driveway, a slide gate that groans and stops halfway, or an operator that hums and does nothing. Most of those jobs are diagnosed and fixed the same day. The exceptions are deeper structural failures, like a hinge post that was poured too shallow, where the concrete needs time to cure. For those, we explain exactly what we found, what we’ll do, and what it costs before anything gets opened up. If your gate is stuck open or refusing to close right now, call (469) 530-2485. A real person answers, 24 hours a day.
We work all over Campbell, from the 95008 neighborhoods near Downtown to the ranch-style subdivisions off Winchester Boulevard and the newer builds along the Los Gatos Creek Trail corridor. Our techs know the difference between a gate problem caused by a bad capacitor and one caused by what’s under the post. That local knowledge is the reason our crews show up with the right tools the first time.
Why Carver Gate Repair Is Campbell’s Preferred Gate Repair Company
Campbell homeowners call us because we show up when we say we will and we hand them a written price before touching a wrench. That’s the Garrison Standard, and it’s been in place since 2008. No one in a Carver truck quotes a range and then discovers a “surprise” once the panel is off the hinges. The number on the written estimate is the number on the invoice. Period.
Every technician who arrives at a Campbell home is background-checked and in uniform. You know the name of the person walking through your gate before they get there. The phones are staffed by a live person around the clock, including weekends and holidays. Lonnie Burke set that rule because voicemail boxes cost homeowners half a day when a gate is stuck open and the dog is loose.
Our Gate Repair team carries parts for Viking, Ghost Controls, DoorKing, and Elite operators on the truck. That means most Campbell jobs get finished in one visit, not three. And every repair is covered by the 365-Day Done Right Promise. If the same part fails inside a year, the second visit is free. That’s in writing.
Driveway Gate Repair in Campbell
Driveway Gate Repair in Campbell typically runs $240 to $520 for an operator service or minor alignment, and $800 to $1,900 when a hinge post has to be pulled, re-poured to a deeper footing, and re-hung. The price depends on whether we’re fixing the mechanical side, the electrical side, or both. Most jobs blend the two, because a gate that binds mechanically will overload the operator and burn it out.
Operator and motor service
When a Campbell gate operator runs but the gate doesn’t move, the usual culprits are a stripped gear rack, a failed limit switch, or a capacitor that’s given up after years of heat and moisture. We test the operator under load, check the limit switch settings, and replace worn parts with components matched to the brand already installed.
Post and hinge alignment
Swing gates in Campbell sag when the hinge post starts leaning. The soil here is what does it. Most lots sit on old orchard ground, where irrigation cycles from the Santa Clara Valley Water District cause clay-loam soil to swell and shrink. A post set 18 or 24 inches deep moves enough to throw the gate off plane. We pull it, pour a deeper column, and re-hang the leaf so it swings clean.
Gate Welding in Campbell
Gate Welding in Campbell is how we fix the failures that replacement parts can’t address. When a steel gate frame cracks at a weld joint, when a hinge plate tears away from the stile, or when a decorative aluminum panel separates from its frame, a new hinge or a new operator won’t solve the underlying problem. Campbell averages $180 to $450 for an on-site weld repair, depending on the length of the crack, the position of the break, and whether the gate leaf needs to come off for repair on the ground.
On-site steel repair
Most structural welds on Campbell driveway gates can be done with the gate still hung. We grind out the crack, repair the joint, and re-check the gate’s swing or slide path before we pack up. If a weld is in a load-bearing spot, we’ll add a gusset rather than just laying a bead over the crack, because the first crack usually means the original design was underbuilt for that span.
Aluminum gate repair
Aluminum gates crack differently than steel. They’re lighter and rust-resistant, but they fatigue at the hinge sleeves and where the frame members meet. We TIG-weld those joints on site, then re-check the hinge alignment. If the panel is too far gone for welding, we’ll say so plainly and price a new panel rather than patching something that’s going to fail again in six months.
Trusted Brands We Service in Campbell
Campbell gates run on a mix of equipment, and our techs are trained on the brands we see most often here: Viking, Ghost Controls, DoorKing, and Elite. That matters because each brand has its own failure patterns. A Viking swing operator has different limit switch logic than a Ghost Controls unit, and a DoorKing slide operator needs different troubleshooting than an Elite. We stock common boards, gears, and arms for these brands at our Bay Area dispatch, so Campbell customers are not waiting on a two-week parts order when a gate is stuck. The right part on the right truck is the whole game.
Common Gate Repair Problems We See in Campbell Homes
- Shallow hinge posts in clay-loam soil. Campbell’s old orchard parcels expand and contract with the irrigation cycle, and any post set under 30 inches tends to lean within two seasons. That lean is why your gate starts dragging on the latch side.
- Slide gates jumping the rack on shifted aprons. Older Campbell driveways have concrete aprons that move a few millimeters in winter rain and summer heat. If the gate was installed tight to a moving slab, the rack and pinion misalign and the operator trips its overload. We re-shim the track and re-time the operator.
- Corroded low-voltage safety wiring. Keypad and photocell connections at the gate leaf take the brunt of Campbell’s rainy winters and dusty summers. Corrosion at a wire nut is the most common no-close fault we find. We replace exposed wiring with weather-sealed connectors every time.
- Operators burned out by a binding gate. A gate that doesn’t swing free makes the operator work harder, and the motor dies early. By the time most Campbell homeowners call us, the opener has already been struggling for months. That’s why we always lube, align, and load-test the gate before installing a new operator, not after.
Pricing for Gate Repair in Campbell, CA
Here’s what Campbell homeowners should expect to pay, based on the jobs we do most often in the 95008 and surrounding area. Operator troubleshooting and service: $240 – $370. Hinge replacement with post re-alignment: $380 – $650. Full hinge post pull, deeper footing pour, and re-hang: $900 – $1,900. On-site weld repair: $180 – $450. New operator installation including safety edges and photocell verification per UL 325: $1,400 – $2,800. These are the numbers we quote most in Campbell, and they’re the numbers on the written estimate you get before we start. Call (469) 530-2485 and we’ll work up your exact price from the specific gate and operator you have.
We Also Serve Cities Near Campbell
Our Gate Repair in Campbell team also runs calls to Saratoga, Los Gatos, Santa Clara, and Cupertino on the same dispatch schedule. If you’re just outside Campbell, the same crews, the same written pricing, and the same live-person phone line apply. No separate office, no different rules.
Serving Campbell, CA – Our Local Coverage Area
We’re based in the Campbell area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Campbell
A gate hinge post in Campbell should be set at least 30 inches deep, with concrete surrounding the post on all sides. The standard 24-inch post pour lasts in stable soil, but Campbell’s clay-loam expands and shrinks with the Santa Clara Valley Water District irrigation cycles and the summer dry season. We regularly find 18-inch post holes that have rotated out of plumb within two years. A 30-inch footing is the minimum we recommend here, and for heavy double-swing gates on sloped lots, we go deeper. Call (469) 530-2485 and we’ll check your existing post depth before you spend money on a new operator that’s only going to burn out against a binding gate.
Yes. Any gate operator that can make a gate move under power is required by UL 325 to have an external entrapment protection device, which usually means a set of photo eyes that reverses the gate when something is in the path. On Campbell’s older gates, this is often the component that’s been bypassed or corroded out. We test every photocell with a physical obstruction before we call a job done. If your gate operator doesn’t reverse against a test box, we’ll tell you, and we’ll show you the written test result. Estimates are free.
A swing gate that drags on the ground usually means the hinge post is leaning, which is a footing problem in Campbell more often than a hinge problem. As the clay-loam soil shifts with irrigation and rain, the post tilts, and the gate’s latch side drops. Tightening the hinge bolts helps for a week or two, but the real fix is pulling the post, pouring a deeper footing, and re-hanging the leaf on a new hinge line. That’s a $900 to $1,900 job in Campbell depending on gate weight and post size. Call (469) 530-2485 for an exact price based on your post and panel.
Yes, we carry a mobile welding rig to Campbell homes and handle most weld repairs on site. A cracked frame joint, a torn hinge plate, or a snapped picket can usually be welded with the gate still hung, depending on access and the weld position. On-site weld repair in Campbell runs $180 to $450. If the gate has to come down and go to a shop for major structural work, we’ll tell you that during the estimate, not after the panel is unbolted.
Most Campbell gate repairs are finished in one to three hours on site, assuming the parts are on the truck. Operator service, hinge replacement, and weld repairs are one-visit jobs. The exception is a hinge post that needs a new deep footing: the concrete has to cure properly before we re-hang the gate, so we do the excavation, set the new post, and schedule the re-hang and operator re-time one to three days later. You get a written schedule with the written price. Call (469) 530-2485 and we’ll tell you exactly which timeline applies to your gate.
Call Carver Gate Repair in Campbell
If your gate is stuck, dragging, or refusing to close, call (469) 530-2485. A live person answers. We’ll ask what the gate is doing, give you a straight answer about likely cause, and get a uniformed, background-checked technician to your Campbell home with the right parts and a written price that doesn’t move. The Garrison Standard applies to every job: written estimate before work starts, a written guarantee good for a full year, and a free second visit if the repair fails within that window. Scheduling is coordinated from our San Francisco Bay Area office, and our crews serve Campbell directly.
Written by Lonnie Burke, Owner at Carver Gate Repair, operating to the Garrison Standard.