Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Farmers Branch
Gate repair in Farmers Branch, TX typically runs $145 – $680 depending on whether we’re fixing a hinge post, replacing a gate operator, or rebuilding a sagging metal frame. Most repair jobs take a technician 2 – 4 hours on site, and we carry the common parts for LiftMaster, Linear, Viking, Ghost Controls, and DoorKing systems to keep the work moving. If your gate drags, stalls, or won’t latch, call (469) 530-2485 and you’ll reach a live person who can schedule a background-checked technician to your Farmers Branch home. We give you a written price before any work starts, and every repair carries a written one-year guarantee.
Why Carver Gate Repair Is Farmers Branch’s Preferred Gate Repair Company
Farmers Branch homeowners keep calling us back because we show up when we say we will, and the price we quote is the price on the invoice. The crew dispatches from our Dallas-Fort Worth office, so a technician can typically reach most Farmers Branch neighborhoods within 60 – 90 minutes for scheduled work. We answer the phones around the clock with a live person, not a voicemail tree. Lonnie Burke runs the operation, and every technician who steps onto a Farmers Branch property is background-checked and in uniform. You know exactly who you’re letting through your gate.
Homeowners in Brookhaven, Valwood Park, and the neighborhoods around Farmers Branch Creek tell us the same thing: they’ve had generalist contractors patch a sagging gate, only to watch it drag again in the next rainy season. That’s because the real problem is usually under the surface, in the post footing. We address the cause, not the symptom, and we put the one-year guarantee in writing on every repair. If the same issue returns inside that year, we come back and fix it at no charge.
Metal Gate Repair in Farmers Branch
Metal gate repair in Farmers Branch covers the full range: straightening bent frames, replacing worn hinge pins and weld points, re-hanging a gate that’s dropped out of plumb, and welding rust-damaged sections before they fail completely. Steel and wrought-iron gates on Blackland Prairie clay take a beating, because the soil under the post footing moves with every wet-dry cycle. A metal gate that’s dragging across the driveway or latching off-center usually means the hinge post has moved, not that the frame is bad. Metal gate repair work in Farmers Branch commonly runs $175 – $520 depending on whether we’re welding, re-hanging, or resetting a post footing.
Frame Straightening and Weld Repair
Drive-gate frames bend over time from wind load, kids on the gate, or a car bump. We cut and re-weld failed joints, straighten rails, and reinforce the corners where stress concentrates. The goal is a gate that swings square and stays square.
Post Reset and Re-Hang
When the hinge post leans, the gate will never close right. We excavate the old footing, set the post plumb in concrete, and re-hang the gate with new hinges. This is the repair that actually lasts in Farmers Branch clay.
Wood Gate Repair in Farmers Branch
Wood gate repair in Farmers Branch usually means fixing rot, sagging frames, warped pickets, or hinge screws that have stripped out of soft lumber. Wood expands and contracts hard in our climate. A gate that latches fine in January can bind in July because the wood has swollen in the humidity. Common wood gate repair work in Farmers Branch runs $145 – $420. The highest-value fix is a compression cross brace and steel corner brackets installed after we bring the gate back to square, not just another hinge adjustment that fails in the next heat wave.
Rot Removal and Reinforcement
Bottom rails and hinge-side stiles rot first. We cut out the dead wood, sister in treated lumber when practical, and replace structural members when they’ve lost integrity. Then we seal and repaint to keep Farmers Branch sun and moisture from doing it again.
Sag Correction With Compression Bracing
A compression brace takes load off the hinge post and transfers it to the latch side. When installed correctly, it’s the difference between a gate that holds square for six months and one that starts dragging by the next wet spring.
Trusted Brands We Service in Farmers Branch
Our technicians work on nine gate-motor brands, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. In Farmers Branch, the systems we see most often are LiftMaster and Viking swing operators on residential drive gates, with some Ghost Controls and DoorKing units on the older ranch-style properties. We stock control boards, limit switches, receivers, and remote transmitters for these brands locally, so a repair doesn’t sit waiting on a part from a warehouse across the country. That means faster turnaround for Farmers Branch customers, and fewer days with a gate stuck open or shut.
Common Gate Repair Problems We See in Farmers Branch Homes
- Clay-driven post heave. The Blackland Prairie soil under Farmers Branch swells when wet and shrinks when dry. Over time, the expansion lifts and tilts hinge posts, which is why a sagging gate returns months after a panel-only fix. The proper repair re-sets the post footing, not just the hinges.
- Summer heat and grit binding slide gates. From June through September, steel rollers packed with dust and grit seize up, and the motor strains until it stalls or the rack jumps teeth. We flush and replace rollers before they damage the operator gearbox.
- Photocell and keypad failures. Safety sensors on Farmers Branch gates face direct Texas sun and rain. The wiring corrodes, the lens clouds, or a mower knocks the beam out of alignment, leaving the gate stuck open or closing on obstructions. The UL 325 safety systems need periodic test and alignment.
- Operator gear wear on older systems. Maybe the limit switch failed, so the gate no longer stops at the right point. Maybe the control board’s capacitor is swelling and the motor won’t start reliably. We diagnose these down to the component and replace only what’s failed, not the whole operator if it’s still sound.
Pricing for Gate Repair in Farmers Branch, TX
Gates in Farmers Branch aren’t all the same, so neither are the invoices. Wheel and roller replacement on a slide gate runs $120 – $230. A swing gate re-hang with new hinges runs $180 – $340. Re-setting a heaving hinge post footing runs $320 – $520, depending on depth and access. A gate operator control board replacement runs $260 – $480 for most brands. A full swing gate operator replacement runs $750 – $1,300 installed, and a full slide gate operator runs $900 – $1,600 depending on weight and duty cycle. Power runs, safety edges, and loop detectors add to the job. Every price we give you is written down before we begin, and our technician walks you through it. Call (469) 530-2485 for a free estimate.
We Also Serve Cities Near Farmers Branch
Our Gate Repair crews work throughout the Dallas-Fort Worth metro, and we regularly take jobs in Addison, Carrollton, and Irving. If you’re outside Farmers Branch but still in the area, call us and we can likely help. Our Farmers Branch page has more about the neighborhoods we cover and what to expect on a service call.
Serving Farmers Branch, TX – Our Local Coverage Area
We’re based in the Farmers Branch area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Farmers Branch
Because the hinge post footing moved. Farmers Branch sits on the Blackland Prairie, and the expansive clay soil shrinks and swells with every wet-dry cycle. It lifts and tilts post footings, pulling hinge posts out of plumb, so a gate re-hung on a moving post will sag again within months. The lasting fix re-sets the post deeper and wider, then re-hangs the gate. Call (469) 530-2485 for an honest assessment.
Yes. Automatic gates are required to meet UL 325 entrapment protection standards, which means working photocells and reversing edges that stop the gate from closing on a person, pet, or car. There is no legal way to bypass those on a functioning Farmer’s Branch gate. If your sensors are misaligned or corroded, we repair or replace them and test the reversal function. Call (469) 530-2485 and we can test your gate’s safety loop and photocells.
Grit-packed rollers and a heat-soaked operator are the usual suspects. Rollers clogged with dust bind the gate, the motor pulls more amps, and it overheats and shuts down on thermal overload. We clean or replace the rollers, lubricate the track, and test the motor’s amp draw against the nameplate to confirm the operator isn’t fighting the gate. Call (469) 530-2485 for a service call before the gearbox takes the punishment.
Gate repair in Farmers Branch runs $145 for a simple hinge or latch fix up to $1,600 for a full slide gate operator replacement. Most repairs land between $180 and $520. The price is always in writing before we start work, so the number never moves at the door. Call (469) 530-2485 with a description of what the gate is doing, and we can usually get you into the right range over the phone.
Yes, if the gate weighs under the opener’s rated limit and there’s a clear sky. Solar openers work on swing and some slide gates, but they’re best for lighter wood gates and infrequent use. Farmers Branch summers give excellent solar exposure; the real limits are gate weight, post strength, and battery capacity through a cold or cloudy winter week. Call (469) 530-2485 and our technician can assess the gate and the sun exposure before you spend money on equipment.
For fast, honest gate repair in Farmers Branch, call Carver Gate Repair at (469) 530-2485. Written price before we start. One-year written guarantee on every repair. Live person on the phone, every time.
Written by Lonnie Burke, Owner at Carver Gate Repair, serving Farmers Branch and the Dallas-Fort Worth metro since 2008.