Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Midlothian, TX
Carver Gate Repair is a gate company serving Midlothian, TX with repair, installation, and motor work on residential and light-commercial gates. What changes the job here is the housing stock itself: Midlothian has a high share of properties on one-acre and larger lots, so many gates are long driveway spans with heavy steel or iron construction, not the 12-foot suburban lane gates you see closer to Dallas. Heat, soil movement, and the way Ellis County clay expands and contracts put real strain on posts, hinges, and motor mounts. If your gate is sagging, slow, or stopped responding, call us at (469) 530-2485 and we’ll get a technician out to look at it.
Why Midlothian Homes Are Different
Midlothian sits on a specific kind of soil. What builders and foundation contractors in Ellis County know well is that the local clay holds and releases moisture in dramatic cycles – wet winters swell it, dry summers shrink it. A gate post set in that soil moves. Not much, but enough. Half an inch at the base becomes two inches of sag at the latch end of a 16-foot gate, and that sag is what kills hinges and throws motors out of alignment.
The housing mix in Midlothian does the rest. The city grew in clear waves: older ranch-style homes with chain-link or simple tubular steel gates near the historic downtown core, and then a long belt of newer developments on the west and north sides where custom iron gates, brick columns, and electric openers are standard. Homes in neighborhoods like Lakeview, Autumn Run, and Longbranch often have gates that were installed with the house and have been running since day one with no real preventive care. A lot of the calls we take in Midlothian are from homeowners whose gate worked fine for eight or nine years and then stopped mid-cycle one morning. That is the soil movement catching up with the mounting, not a sign that the gate itself is done.
Our Main Midlothian Services
Most Midlothian calls fall into two buckets: a gate that will not open or close properly, and a motor that will not respond at all. Below are the three services we run in this city, each with its own page that covers local scope and pricing.
Gate Repair in Midlothian
Sagging gates, broken hinges, failed welds, and latch misalignment are the common problems on Midlothian properties, especially on longer driveway spans where the weight of the gate works against the posts year after year. We straighten, reinforce, re-weld, and re-hang. We also replace hardware like rollers, hinges, and latch assemblies with parts matched to the existing frame. If your gate is dragging on the ground or leaving a mark on the concrete in a Midlothian driveway, the repair is usually straightforward once the post issue is corrected. Gate Repair in Midlothian.
Gate Installation in Midlothian
New construction and replacement gates in Midlothian need posts set deeper than the minimum, because of the clay soil movement described above. We pour posts with concrete below the active soil line, set the frame square, and hang the gate with the right clearance for the grade. Whether it is a driveway swing gate, a walk gate, or a matched pair, every Midlothian install gets a written price before any material is ordered or any hole is dug. Gate Installation in Midlothian.
Gate Motor Repair in Midlothian
When a Midlothian gate motor hums but does not move, or trips its breaker, or opens an inch and reverses, the issue is usually in the operator, the limit switch settings, or a loop detector that has lost its signal. We work on Viking, Ghost Controls, DoorKing, and Elite systems, among others, and we diagnose the motor as a system, not as an isolated part. A Midlothian motor that has been exposed to years of heat and dust can often be brought back with the right part and calibration. Gate Motor Repair in Midlothian.
What happens when you call
- 1
A real person answersNo phone trees – you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Midlothian
We carry parts and have training on nine gate-motor brands. In Midlothian we see a lot of Viking, DoorKing, Elite, and Ghost Controls systems on residential installations. That means we can usually match a failed board, arm, or limit switch with the correct replacement on the first visit, rather than wiring in something that “sort of” works. See our brands for the full list.
Pricing for Gate Company in Midlothian, TX
| Service | Typical range in Midlothian |
|---|---|
| Gate repair diagnostic fee | $75-$125 (waived with repair) |
| Hinge replacement (per hinge) | $90-$220 |
| Sagging gate realignment | $200-$550 |
| Weld repair (per location) | $150-$400 |
| Latch or lock replacement | $125-$350 |
| Gate motor replacement (single arm operator) | $950-$1,750 |
| Limit switch replacement | $180-$320 |
| Loop detector replacement | $250-$450 |
| Receiver / keypad replacement | $175-$375 |
| New driveway gate (single swing, steel) | $2,200-$6,500 |
Two things push cost in Midlothian more than anything else: the length and weight of the gate itself, and whether the posts have shifted enough to need resetting. Every job, from a hinge swap to a full driveway gate, gets a written price before the work starts. That number does not change at the door.
Neighborhoods We Serve in Midlothian
Our technicians cover the full Midlothian city limits and the unincorporated Ellis County areas around it, from the older streets near the downtown square to the newer subdivisions on the north and west edges. Typical response window for a repair call in Midlothian is same-day or next-day, depending on the time of the call and parts availability.
- Lakeview
- Autumn Run
- Longbranch
- Kensington Park
- The Grove
Service Area – Cities Near Midlothian
Carver Gate Repair’s Midlothian crews also take calls in the surrounding Ellis County and southern Dallas County areas. If you are in one of the cities below, the same written-price and background-checked technician standard applies:
Cedar Hill, TX | Mansfield, TX | Waxahachie, TX | Red Oak, TX
Serving Midlothian, TX – Our Local Coverage Area
We’re based in the Midlothian area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Midlothian
Most Midlothian repair calls get a same-day or next-day visit, depending on when you call and what parts the job needs. Motor replacements may take a day longer if a specific board or arm has to come from the supplier. Call (469) 530-2485 and the dispatcher will give you a real arrival window.
For most residential gate repairs and like-for-like replacements, Midlothian does not require a permit. A new driveway gate on the front setback, or any installation that changes access to the property, may fall under city review. We can tell you what applies to your lot.
Shared gates and shared fence lines in Midlothian sometimes need both property owners to agree on scope. We can write the repair or replacement quote so it is clear what is covered, which makes the conversation with a neighbor simpler. The written price covers the work described; nothing gets added after the fact.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Midlothian Customers Say
"Gate hinge was bending under the weight. Welded a new bracket on and re-hung it. Solid now."
- Rudy A."Slide gate wasn't opening fully. Veteran tech found a worn drive chain and a misaligned limit. Fixed both in one visit."
- Don H."Good repair on a motor board. Waited a few days on the part, but they stayed in contact."
- Shelby T.