Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Weatherford
When a gate stops opening in Weatherford, you don’t need a general contractor who does gates on the side. You need someone who understands why Parker County gates fail, shows up on time, and writes the price down before touching a tool. Carver Gate Repair sends background-checked, uniformed technicians to Weatherford every week, and every repair carries our written 365-Day Done Right Promise. Call (469) 530-2485 and a live person answers – 24 hours a day, every day of the year, weekends included.
Why Carver Gate Repair Is Weatherford’s Preferred Gate Repair Company
We work on gates full time. That’s the whole job. Homeowners off Tin Top Road, along Bethel Road, and out near the 76087 and 76086 zip codes call us because the gate that fails on a Saturday morning is the same gate we have already fixed a hundred times in similar Parker County soil. The Garrison Standard governs how we operate: written prices, a full-year guarantee on every repair, and a free second visit if the repair fails inside that window. No argument, no invoice, no runaround.
Lonnie Burke runs our crews to this standard, and it shows in how jobs get finished. The site is clean when we leave. The operator is tested through a full open and close cycle, including the safety reversal. The price on the invoice matches the price on the written quote you approved before work began. That’s the Gate Repair process we bring to Weatherford, and it’s why homeowners in Aledo and Springtown also call us when their gates go down.
Iron Gate Repair in Weatherford
Iron gate repair in Weatherford usually starts with a gate that has started scraping the ground or binding at the latch. The panel itself is rarely the problem. It’s almost always the post, the hinge barrel, or the footing underneath them. Weatherford’s blackland clay expands in spring and contracts through the dry summer, and that seasonal movement slowly pushes posts out of plumb. A gate that swung clean last October will drag by May. We see it every year across the county.
Hinge and Post Repair
When an iron gate binds, the hinge post is the first thing we check. A sagging panel tells us the post has rotated in wet clay or the weld at the hinge has started to crack. We reset and shim the post, reweld where needed, and re-hang the gate so the reveal gap is consistent top to bottom. A proper fix means the gate swings without lift or drag through all four seasons, not just the day we leave.
Weld and Rust Repair
Weatherford’s humidity and occasional ice storms take a toll on iron gates, especially at the bottom rail and the hinge welds where water sits. We grind back surface rust, treat the steel, and weld cracks before they spread. On gates with decorative scrollwork, we match the existing profile rather than patching with whatever rod is on the truck. Repairs are painted to match, and the finish gets a primer coat that holds up to Parker County weather.
Sliding Gate Repair in Weatherford
Sliding gate repair in Weatherford most often comes down to two things: a rack and pinion that has worn out of mesh, or a track that has shifted because the driveway settled. Slide gates are common on the longer rural driveways east of Mineral Wells and north of Interstate 20, where a swing gate would need too much clearance. When a slide gate starts jerking or stalls halfway, the operator is usually blamed. The fault is more often mechanical.
Track Alignment and Roller Replacement
A slide gate rides on rollers through a track, and when clay heave pushes one section of the track up or sideways, the gate starts fighting the motor. That strain shows up as a burned-out capacitor or a tripped limit switch. We level and anchor the track properly, replace worn rollers, and retension the chain or rack so the operator isn’t doing work the track should be doing.
Operator Diagnostics on Slide Gates
Before we replace any motor, we test the full circuit: limit switches, loop detector, photocells, and the power feed from the panel. On a ranch property off Ric Williamson Memorial Highway, we handled a slide gate that would stall halfway. The culprit was a chewed loop detector lead and an undersized post footing that had heaved with the clay. We repoured the footing, replaced the loop detector, retensioned the rack and pinion on the LiftMaster operator, and the gate has run clean through two wet seasons since.
Trusted Brands We Service in Weatherford
Our technicians carry parts for the gate operators already installed on Parker County properties: FAAC, BFT, Linear, and Viking gear show up regularly on Weatherford driveways, along with LiftMaster and DoorKing on the bigger ranch entrances. We keep common boards, limit switches, and remote receivers stocked so a repair doesn’t wait on a parts shipment from Dallas. If the operator on your gate is older and the manufacturer has discontinued the board, we will tell you that plainly and price the replacement honestly before we touch anything.
Common Gate Repair Problems We See in Weatherford Homes
- Seasonal post movement. Blackland clay and caliche subgrade expand and contract through Weatherford’s dry-to-wet swings, pushing hinge posts and slide track footings out of alignment. A gate that binds every spring usually has a footing problem, not a hinge problem.
- Rodent damage to loop detectors and safety edges. Rural Parker County properties have mice, rats, and squirrels that chew low-voltage wiring. A gate that won’t hold open or reverses for no reason often has a severed loop detector lead underground.
- Voltage drop on long power runs. When a gate operator pulls power from a barn or shop subpanel rather than the house, the longer wire run drops voltage under load. The operator still works, but it runs hot and burns boards early. We check the gauge and the grounding before we blame the motor.
- Track misalignment on unlevel driveways. Slide gates on rural lots often run slightly uphill or across a grade change. The track settles unevenly, the gate drags, and the operator faults. Fixing the track is cheaper than replacing an operator that was never the problem.
Pricing for Gate Repair in Weatherford, TX
Gate repair pricing in Weatherford stays within a predictable range once we know what failed. A hinge and post realignment on an iron gate commonly runs $275 to $500 depending on whether we need to cut and reweld. A slide gate track level and roller replacement usually comes in between $400 and $800. Operator board replacements run $350 to $700 depending on the brand, and a full operator swap with new safety edges is $1,100 to $2,400 installed. Every quote is written, approved, and signed before work starts. The number on the quote is the number on the invoice. Call (469) 530-2485 for a free estimate on your specific gate.
We Also Serve Cities Near Weatherford
Our crews dispatch to Weatherford daily and regularly run service calls out to Gate Repair in Weatherford neighbors in Aledo, Springtown, Azle, and Mineral Wells. If you live in the county between those towns, call us. If we cover the address, we’ll send someone out with the same written-price promise.
Serving Weatherford, TX – Our Local Coverage Area
We’re based in the Weatherford area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Weatherford
Blackland clay expands with spring moisture and lifts the ground around your hinge post or slide track footing. The gate doesn’t bend; the post moves, and the panel drags. The fix is resetting the post on a deeper footing or leveling the track, not grinding the gate shorter. Call (469) 530-2485 and we’ll diagnose the actual cause before you pay for another adjustment that won’t hold.
Yes. Many Weatherford area properties pull gate power from a barn or shop subpanel rather than the house meter, and that changes the wiring decisions. We check the voltage under load, the grounding rod placement, and the wire gauge to the operator before we install or repair anything. If the power feed is wrong, we’ll tell you and fix that first.
We service and install FAAC, BFT, Linear, Viking, LiftMaster, Ghost Controls, DoorKing, Elite, and Mighty Mule operators. That covers nearly every swing and slide operator currently running on Parker County driveways. If you have a lesser-known brand, call us anyway; we can usually identify it from the control board and match the parts.
A standard iron gate hinge and post repair takes one visit, usually half a day with curing time for the concrete. A full gate installation with operator, safety edges, and power run takes two to five days depending on the scope and whether we are pulling a permit for the electrical. We never promise same-day turnaround on an installation. You get a written schedule and a written price before the first hole is dug.
A proper installation includes the gate panel, hinge or slide hardware, an operator sized for the panel weight, a power run with adequate gauge wire, working photocells and safety edges, and a reversal test done with a physical obstruction. Before you pay any installer, ask whether the safety reversal will be tested at the final walkthrough. If the answer is vague, call (469) 530-2485 instead. Our installations include the test, the written guarantee, and the 365-Day Done Right Promise.
Written by Lonnie Burke, Owner at Carver Gate Repair, serving Weatherford and Parker County with written prices and a full-year guarantee on every repair.
Contact Carver Gate Repair in Weatherford
Need a gate fixed? Call (469) 530-2485 and a live person picks up. We schedule a time that works, send a background-checked technician in uniform, and put the price in writing before any work begins. The guarantee is written on the invoice: if it’s not done right, we make it right, free, for a full year. That’s The Garrison Standard, and it applies to every gate we touch in Weatherford.