Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Calabasas, CA
Gate repair in Calabasas runs into the same three problems on almost every job: heat that cooks circuit boards inside motor housings, hillside lots that put real strain on hinges and operators, and HOAs that demand gates look and work a certain way. Carver Gate Repair handles all of it. We’re the gate specialist for Calabasas, with background-checked technicians, a written price before any work starts, and a full-year guarantee on every repair. If your gate is stuck, sagging, or dead at the panel, call (469) 530-2485 and a live person answers, day or night.
Why Calabasas Homes Are Different
Calabasas gates take more abuse than most people realize. Summer temperatures through the western San Fernando Valley regularly push past 100 degrees, and a black steel gate in direct sun can get hot enough to fry the control board inside a swing operator. We see it constantly in neighborhoods like The Oaks, Mountain View Estates, and Calabasas Hills. Homes built into the Santa Monica Mountain foothills also deal with slope, which means a gate that was hung level ten years ago may no longer close square because the ground has settled underneath the posts.
Beyond the climate and terrain, Calabasas has strict HOA standards in most subdivisions. Gate styles, paint colors, and even motor placement often need to match what the association approved. Our technicians work with homeowners to make sure a repair or replacement doesn’t end with a notice from the management office. That means matching existing hardware where possible, keeping noise levels low for properties close to neighbors, and routing conduit so it doesn’t run exposed across a driveway apron.
Our Main Calabasas Services
Most Calabasas calls come down to two things: a gate that won’t move, or a gate that’s being replaced. The three pages below cover what homeowners in Calabasas actually need to know.
Gate Repair in Calabasas
A gate that drags, binds, or stops halfway usually has a mechanical problem: worn hinge bearings, a bent wheel track on a slide gate, or a post that has shifted on a hillside. Calabasas properties on sloped lots put more load on hinges than flat sites do, so we check post alignment as part of every repair, not just the visible hardware. From re-hanging dropped gates to replacing broken pickets and latch hardware, we quote the full job before we touch a tool. See Gate Repair in Calabasas for what’s covered and what repairs typically cost.
Gate Installation in Calabasas
Installing a new gate in Calabasas means matching the style the neighborhood expects, whether that’s a wrought-iron driveway gate in guard-gated Calabasas Park or a simpler steel pedestrian gate in an older hillside lot. We measure, order, and schedule installation on your timeline, and we handle the concrete, the hardware, and the operator mounting in one job. No estimate games, no half-finished site left behind. Get the full scope on Gate Installation in Calabasas.
Gate Motor Repair in Calabasas
When the motor hums but the gate doesn’t move, or the remote stopped working, the problem usually sits inside the operator box: a dead capacitor, a failed limit switch, or a control board that gave out after one too many heatwaves. Our technicians carry parts for Viking, Ghost Controls, and DoorKing operators on the truck, so most Calabasas motor repairs are done in one visit, not three. Full details on Gate Motor Repair in Calabasas.
What happens when you call
- 1
A real person answersNo phone trees – you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Calabasas
We service and install Viking, Ghost Controls, DoorKing, and Elite gate operators and hardware. Most common parts, including boards, limit switches, and remote transmitters, stay stocked on our trucks so a Calabasas repair doesn’t wait on a parts order. See our brands for the full list of equipment we support.
Pricing for Gate Company in Calabasas, CA
| Service | Typical range in Calabasas |
|---|---|
| Gate motor replacement | $850 – $1,900 |
| Control board replacement | $350 – $700 |
| Hinge replacement (standard steel) | $200 – $500 |
| Gate wheel / roller replacement | $180 – $450 |
| Safety sensor repair or replacement | $150 – $350 |
| Remote programming and replacement | $75 – $200 |
| Track repair or re-alignment (slide gates) | $400 – $1,100 |
| Weld repair (on-site, per point) | $120 – $300 |
Two things push pricing up in Calabasas more than anything else: slope and finish. Gates on hillside driveways often need custom hinge work or heavier operators, and ornamental iron that has to match an HOA-approved finish costs more to repair properly than standard steel. Whatever the job, you get a written price before we start, and that number is the number on the final invoice.
Neighborhoods We Serve in Calabasas
We work throughout Calabasas and the surrounding foothill communities. Typical response for a gate repair call is same day or next morning, depending on when you call and how close the crew is to your side of town.
- The Oaks
- Calabasas Hills
- Mountain View Estates
- Calabasas Park
- Mulwood
Service Area – Cities Near Calabasas
In addition to Calabasas proper, our crews cover the neighboring foothill and valley communities, including Topanga, CA, Agoura Hills, CA, Oak Park, CA, and Westlake Village, CA. If your property sits in an unincorporated stretch between city lines, call us and we’ll confirm coverage.
Serving Calabasas, CA – Our Local Coverage Area
We’re based in the Calabasas area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Calabasas
Most Calabasas calls are answered same day, and many are completed the same day. A gate stuck open or shut is a safety and security issue, so we prioritize emergency calls in the Calabasas area. Call (469) 530-2485 and a live person will give you a real arrival window, not an automated message.
Usually not for a repair that restores the gate’s existing function and appearance. If you’re changing the gate style, color, or adding a new operator, your HOA may need to approve the plans first. Our technicians keep repairs within the existing footprint and finish, which avoids most approval issues. Call (469) 530-2485 and we’ll walk you through what your association is likely to require.
Yes. Our technicians are background-checked and carry identification, and we’re familiar with the entry procedures for guard-gated communities like Calabasas Park. When you schedule, let us know the community and gate code procedure, and we’ll handle the rest. Call (469) 530-2485 to book a time.
Call Carver Gate Repair at (469) 530-2485 for a free estimate on any gate repair, installation, or motor job in Calabasas. A real person answers, around the clock.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Calabasas Customers Say
"Showed up a little after the window, but he called ahead. On time otherwise, polite, and efficient. Cleaned up all the tools."
- Joan K."Swing gate arm snapped. They replaced the actuator and tested the safety reverse. Fair price."
- Angela P."Keypad and remotes set up fresh for the whole neighborhood. Done cleanly and quickly."
- Chris W.