Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Malibu, CA
Carver Gate Repair is the gate company Malibu homeowners call when a gate stops opening, sags past the latch, or starts making a noise it shouldn’t. We work on gates and gate motors only, so our technicians know the systems in this area: salt air against steel, steep driveways that shift gate posts, and older custom gates that aren’t in any manual. If your gate is down, call (469) 530-2485 and a live person picks up, day or night.
Why Malibu Homes Are Different
Malibu gates live harder than gates almost anywhere else in Los Angeles County. The salt air off the Pacific gets into hinges, tracks, and motor housings. Steel hardware that would last fifteen years inland can show corrosion in five, especially on properties at or below the highway where fog sits overnight. Gate posts set into steep hillsides shift as the ground moves during winter rains, which throws off alignment and forces the gate to bind or stop mid-cycle. Many Malibu homes use custom wood or ornamental steel gates built to match the architecture. Those gates are heavy, often 300 pounds or more, and the motors running them need to be sized correctly from the start. In neighborhoods along Pacific Coast Highway, Point Dume, and the canyons off Malibu Canyon Road, we regularly see systems where the gate was installed correctly but the motor is undersized for the weight it’s pushing. That’s the first thing we check. Coastal properties also face tougher HOA standards for gate appearance, noise, and setback. A repair that works but changes the look of the gate may need board approval before it goes in. We’ll tell you if that applies to your street.
Our Main Malibu Services
The three services Malibu homeowners call us for most are below. Each has its own page with local pricing, timelines, and what the job involves in this specific area.
Gate Repair in Malibu
Gate repair here usually means one of three things: a sagging or binding gate, a gate that won’t open or close fully, or hardware that’s failed from salt corrosion. We fix hinges, replace wheels and rollers, straighten posts, repair welded joints, and rebuild latch and lock hardware. On coastal properties, we check for rust inside the gate frame itself, not just on the visible hardware. Every repair gets a written quote before work starts and a one-year written guarantee when it’s done. See the full breakdown on the Gate Repair in Malibu page.
Gate Installation in Malibu
A new gate in Malibu has to handle the weight of the gate, the slope of the driveway, and the exposure. We measure first, then match the gate and operator to the site rather than forcing a stock size onto a hillside. Installation covers the gate itself, posts set to handle the soil, hinges rated for coastal air, and a motor system matched to the gate’s weight and cycle frequency. Written pricing is agreed before any material is ordered. Details are on the Gate Installation in Malibu page.
Gate Motor Repair in Malibu
When a motor fails near the coast, the cause is often salt corrosion on the control board or limit switches, or a motor that’s been overheating because the gate is too heavy for it. Our technicians open the unit, diagnose the fault, and show you what failed before quoting a repair. We carry parts for Viking, Ghost Controls, DoorKing, and Elite systems, among others, so many Malibu motor repairs are completed on the first visit. The full scope is on the Gate Motor Repair in Malibu page.
What happens when you call
- 1
A real person answersNo phone trees – you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Malibu
We service and stock parts for Viking, Ghost Controls, DoorKing, and Elite systems, along with five other major motor brands. Parts for these four are commonly on our trucks when we roll into Malibu, which keeps most repairs to a single visit. See our brands for the full lineup and what we keep in stock.
Pricing for Gate Company in Malibu, CA
| Service | Typical range in Malibu |
|---|---|
| Gate repair, minor (hinge adjustment, latch alignment) | $150 – $450 |
| Gate repair, major (post reset, welded frame repair) | $650 – $1,800 |
| Gate motor replacement (operator only) | $950 – $2,800 |
| Gate motor repair (limit switch, capacitor, control board) | $250 – $850 |
| New gate installation (single swing, standard materials) | $2,500 – $7,500 |
| New gate installation (custom, heavy, or sliding) | $6,000 – $18,000 |
| Loop detector replacement | $350 – $800 |
| Articulating arm replacement | $400 – $1,100 |
| Safety edge or photo eye replacement | $200 – $500 |
| Keypad or intercom replacement | $300 – $900 |
Malibu pricing runs higher than inland because salt-rated hardware costs more and steep driveways often require extra post work. The written price we give you before starting is the price you pay, and any repair carries a one-year guarantee in writing.
Neighborhoods We Serve in Malibu
We run service throughout the city, from the beach side of PCH up into the canyon roads. Crews typically reach most Malibu addresses within the same day for urgent gate failures.
- Point Dume
- Malibu Park
- Big Rock
- Latigo Canyon
- Malibu West
Service Area – Cities Near Malibu
Beyond Malibu, we run calls into the neighboring communities along the 101 corridor and the Conejo Valley. Our crews cover Agoura Hills, CA, Westlake Village, CA, Thousand Oaks, CA, and Calabasas, CA. Scheduling and dispatch are coordinated from the brand’s Los Angeles office, with crews serving Malibu directly.
Serving Malibu, CA – Our Local Coverage Area
We’re based in the Malibu area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Malibu
For a gate that won’t open or close, we typically reach most Malibu addresses the same day you call. The phone is covered by a live person 24/7, so you can reach us at midnight or on a holiday. Call (469) 530-2485 and we’ll give you a straight arrival window.
Some Malibu HOAs require approval for changes to gate appearance, height, or color, while straightforward repair of existing hardware usually doesn’t. We’ll flag any work that might need board review before we quote it, so you don’t get caught after the fact.
Call us with the gate type and the motor brand, and we’ll tell you if we can take the job. Most of our Malibu work is residential, but we do service some commercial and estate systems where the equipment matches the brands we’re trained on.
If your gate is down or acting up, call (469) 530-2485 for a free estimate. A real person answers, and the price we quote is the price you’ll see on the written work order before any repair starts.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Malibu Customers Say
"Gate hinge was bending under the weight. Welded a new bracket on and re-hung it. Solid now."
- Rudy A."Slide gate wasn't opening fully. Veteran tech found a worn drive chain and a misaligned limit. Fixed both in one visit."
- Don H."Good repair on a motor board. Waited a few days on the part, but they stayed in contact."
- Shelby T.