Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Friendswood, TX
Carver Gate Repair is the gate company Friendswood homeowners call when a gate stops working and they want it fixed without games. Most of the gates we service in Friendswood are automated driveway gates on suburban lots, and the combination of clay-heavy soil, Gulf Coast humidity, and summer heat creates a specific set of problems: motors that overwork, hinges that pull out of wet ground, and control boards that fail after storms. This page is the overview of how we work in Friendswood. Each service has its own detailed page linked below. For a same-day repair or a free quote, call (469) 530-2485.
Why Friendswood Homes Are Different
Friendswood sits on expansive clay soil that shifts with every wet-dry cycle. That movement is hard on gate posts and hinges. A gate that swings clean in March can drag by July. We see it in neighborhoods like Forest Bend, Wedgewood Village, and the newer sections near Friendswood Lakes. Post footings here need to be set below the active soil layer, and the hinge hardware has to tolerate more lateral movement than it would in, say, a sandy-soil city.
Humidity and salt air are the second factor. Friendswood is close enough to Galveston Bay that corrosion moves faster than it does further inland. Limit switches, loop detectors, and exposed brackets on Viking and Linear operators age quicker here. A control board that survives ten years in a drier climate may fail in six or seven in Friendswood if the enclosure isn’t sealed properly.
Finally, Friendswood is largely built on flat terrain with newer subdivisions mixing into older ranch-style lots. That means a lot of swing gates, a growing number of slide gates on newer properties, and plenty of neighborhoods with deed restrictions that control gate height, finish, and even the motor type. If your HOA has a spec sheet, bring it to the first visit. We work to it.
Our Main Friendswood Services
Most calls we get in Friendswood come down to two things: a gate that won’t open, or a gate that needs to exist where there isn’t one yet. Here are the three services we run in Friendswood, each with its own page.
Gate Repair in Friendswood
A sagging gate is the most common repair call in Friendswood, usually after a stretch of rain softens the ground and the post shifts. We level the gate, reset the hinges, and get the travel path clean before a bent wheel or a cracked post turns a $200 fix into a $2,000 replacement. We also handle broken welds, rusted-through frames, and gates that have been hit by a vehicle. Every Gate Repair in Friendswood job gets a written price before we start and a written one-year guarantee when we’re done.
Gate Installation in Friendswood
New gates in Friendswood usually go on new-build lots or replace an old chain-link setup that’s past saving. The design questions are always the same: swing or slide, what the HOA allows, how far the post needs to be set for the clay soil, and whether the driveway has room for an articulating arm operator. We handle the layout, the footings, the steel or aluminum gate, and the motor package as one job with one warranty. Read more on the Gate Installation in Friendswood page.
Gate Motor Repair in Friendswood
When the gate itself is fine but the opener won’t respond, the problem is almost always the motor, the limit switch, or the control board. Ghost Controls and DoorKing systems are common in Friendswood, and both have their own failure patterns in humid weather. We bench-test the board, check the loop detector, and replace only what’s actually dead. The Gate Motor Repair in Friendswood page covers operator brands, diagnostic times, and motor replacement costs.
What happens when you call
- 1
A real person answersNo phone trees – you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Friendswood
We carry parts for Linear, Viking, Ghost Controls, and DoorKing operators, plus the other major brands our crews work on. That means most motor repairs in Friendswood can be finished the same day, since we aren’t waiting on a distributor. See our brands page for the full list.
Pricing for Gate Company in Friendswood, TX
| Service | Typical range in Friendswood |
|---|---|
| Gate repair diagnostic visit (credited to work) | $75 – $125 |
| Driveway gate repair (labor only) | $200 – $450 |
| Driveway gate motor replacement | $600 – $1,400 |
| Gate hinge replacement (steel post) | $150 – $350 |
| Gate post reset (clay soil) | $350 – $800 |
| Swing gate installation (no motor) | $1,800 – $4,500 |
| Slide gate installation (no motor) | $2,500 – $6,000 |
| Swing gate operator install (motor only) | $950 – $2,200 |
| Loop detector replacement | $250 – $500 |
| Limit switch replacement | $150 – $300 |
| Control board replacement | $300 – $700 |
| Remote transmitter programming | $75 – $150 |
In Friendswood, the biggest price driver is the soil. A post that has to be dug out and re-footed below the clay line adds real labor, especially inside a fenced side yard where the auger may not fit. Other drivers are gate size and whether the operator has to be matched to an HOA-approved model. Whatever the number is, it’s written down and agreed to before any work starts. The number doesn’t move at the door.
Neighborhoods We Serve in Friendswood
We work across the full Friendswood area, from the original ranch-style streets to the newer master-planned sections. Our typical arrival window is one day out for non-emergency work, with same-day dispatch available for a gate that won’t close and can’t be secured.
- Forest Bend
- Wedgewood Village
- Friendswood Lakes
- Heritage Park
- Imperial Estates
Service Area – Cities Near Friendswood
We also serve the communities around Friendswood, including Webster, TX, League City, TX, Pearland, TX, and Alvin, TX. Scheduling for Friendswood is coordinated from our Houston office, with crews dispatched locally so travel time stays short.
Serving Friendswood, TX – Our Local Coverage Area
We’re based in the Friendswood area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Friendswood
We answer the phone around the clock and can typically dispatch a technician to Friendswood the same day when a gate won’t secure the property. For non-emergency repairs, the standard window is one business day out. Call (469) 530-2485 and a live person will confirm the schedule.
Yes. Many Friendswood subdivisions have written gate specs covering height, finish, and operator type. We work from the HOA document you provide and make sure the gate and motor match it before installation day, so you avoid a violation letter later.
Permit requirements in Friendswood vary by scope. A like-for-like repair or motor swap generally doesn’t require one. A new gate with new footings can trigger a permit depending on the property. We’ll tell you what your specific job requires at the quote visit.
If your gate needs work in Friendswood, call (469) 530-2485. We’ll give you a written price before any work starts, and the repair carries a written one-year guarantee, no fine print. Ask for Lonnie Burke when you call.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Friendswood Customers Say
"Keypad and remotes set up fresh for the whole neighborhood. Done cleanly and quickly."
- Chris W."Straight answers on whether to repair or replace the operator. Repair was the right call."
- Wanda F."Gate hinge was bending under the weight. Welded a new bracket on and re-hung it. Solid now."
- Rudy A.