Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Atascocita
Most gate installations in Atascocita take one to three days on site, not counting concrete cure time, and a typical driveway gate project runs $3,200 to $8,500 depending on size, material, and automation. That’s the honest range. We are Carver Gate Repair, and we handle gate installation across Atascocita including Atascocita Forest, The Pines, Oaks of Atascocita, Kings River, and Atascocita Springs. Lonnie Burke leads our crews, and every job starts with a written price before any material gets ordered. If you are planning a new gate at your place, call (469) 530-2485 and we will walk the property with you before you spend a dollar.
Why Carver Gate Repair Is Atascocita’s Preferred Gate Installation Company
We work to The Garrison Standard. That means background-checked, uniformed technicians on every call, a written price delivered before any work starts, and a written guarantee on every installation. When Atascocita homeowners call us about a gate that has sagged, an operator that has quit, or a new build that needs a driveway gate from scratch, they get one phone number answered by a live person, 24 hours a day.
Our Gate Installation crew knows what this area’s soil does to gate posts. Atascocita’s expansive clay swells after rain and shrinks during dry stretches off Lake Houston. Shallow concrete just will not hold. We have seen posts set in a foot of concrete move two inches inside a year. That is why we pour deeper, bell-shaped footings here, and why we never quote an Atascocita job the same way we would quote one in a rock-solid inland suburb.
Every job is backed by our 365-Day Done Right Promise. If something is not right within a full year, we come back and make it right. No charge. No argument. Lonnie Burke runs the crews that way, and the guarantee is written into every invoice, not implied.
Gate Opener Installation in Atascocita
Gate Opener Installation in Atascocita is the job we recommend most often for existing gates that have never been automated, or for operators that were installed wrong the first time. We mount the operator, build a dedicated power run, set the travel limits, and then test the entrapment protection until the gate reverses on contact and the photocell breaks the beam every single time. A swing arm operator on a single driveway gate in Atascocita typically runs $1,100 to $2,400 installed. A slide operator on a heavier gate runs $1,800 to $3,500, including the rack and concrete work if needed.
Operator Placement and Power
Older Atascocita neighborhoods often have the operator spliced onto a shared garage circuit. In summer, when every AC unit on the block is pulling hard, that circuit browns out and the operator throws phantom faults or burns a control board. We run a dedicated circuit and mount the operator where water never pools.
Entrapment Protection Testing
Texas follows UL 325, which means an automatic gate needs working safety photocells or an edge sensor, plus a tested reversal. If your gate has an operator without these, we add them before the gate is legal to run automatically. We demonstrate the reversal test for you before we leave and show you the keypad codes.
Gate Fabrication in Atascocita
Gate Fabrication in Atascocita is for homeowners who want a gate built to their driveway, not adapted to it. We measure the opening, check the grade change across the driveway, and order steel or aluminum panels cut to those dimensions. A fabricated single swing driveway gate in Atascocita runs $2,800 to $6,500. A 16-foot double swing gate, which is common in Atascocita Springs and Kings River, runs $5,000 to $9,500 including the center pull post and both hinges.
Built for Atascocita Clay
The panel is only half the job. On Atascocita’s expansive clay, the hinge post carries the whole load of the gate plus the force of the operator. We set that post in a bell-shaped footing that goes below the active clay zone, so the bottom of the concrete flares wider than the top. That shape resists the heave-and-settle cycle better than a straight cylinder of concrete ever will.
Materials and Finish
We fabricate mostly in steel for driveway gates and aluminum for pedestrian and pool gate frames. Steel gets a rust-inhibiting primer and a powder-coat finish in the color you pick. Aluminum is lighter and works well for gates that see regular manual opening. We quote material, finish, and hardware separately so you can see exactly where the money goes before signing anything.
Trusted Brands We Service in Atascocita
Our technicians are trained on Linear, Viking, and Ghost Controls operators, and we stock control boards, remotes, and safety edges for those systems right here for Atascocita jobs. That means when a Linear board fails on a Kings River property, we are not waiting a week on a part out of Dallas. We match the operator to the gate, not the other way around, and if you have a DoorKing slide operator on an aging steel gate, we can rebuild the operator or quote a replacement with the wiring already in place.
Common Gate Installation Problems We See in Atascocita Homes
- Posts set in shallow concrete. Atascocita’s clay soil moves with the Lake Houston water table, and a post set two feet deep will shift enough to bind the gate within a year. We re-set posts on almost every third or fourth repair call here.
- Operators spliced onto undersized circuits. In 1970s and 1980s neighborhoods around Atascocita Forest and The Pines, the operator shares a breaker with the garage or patio. Summer brownouts kill boards. We run a dedicated line.
- Gates hung without UL 325 entrapment protection. A lot of older Atascocita gates were built before the rule was enforced. No photocell, no edge sensor, no tested reversal. We add the photo-eyes and run the reversal test before we call the job done.
- Sagging double gates on Atascocita Springs properties. The 16-foot double swing is the standard there, and when the center pull post moves, both leaves drop and the operator drags. That is a footing problem, not a hinge problem.
Pricing for Gate Installation in Atascocita, TX
| Job | Typical Atascocita Price |
|---|---|
| Single swing driveway gate, fabricated steel, manual | $2,800 – $4,500 |
| Double swing driveway gate, automated | $5,000 – $9,500 |
| Slide gate with operator and rack | $4,200 – $8,500 |
| Gate opener installation on existing gate | $1,100 – $3,500 |
| Pedestrian gate, aluminum, manual | $900 – $2,200 |
These are installed prices for Atascocita, including concrete, hardware, and a written guarantee. The spread comes down to gate width, material, whether we need to pull new electrical, and what the existing footings look like. We quote the job before we start and the price does not move at the door. Call (469) 530-2485 and we will measure your opening and give you a written number.
We Also Serve Cities Near Atascocita
Our crews cover Atascocita daily, and we take Gate Installation in Atascocita calls alongside work in Houston, San Antonio, Dallas, and Fort Worth. Dispatch and scheduling for the Atascocita area are coordinated from the brand’s Houston office, and the same Garrison Standard applies on every job.
Serving Atascocita, TX – Our Local Coverage Area
We’re based in the Atascocita area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Installation in Atascocita
We cannot install a new Atascocita gate the same day because concrete needs time to cure before we hang panels off the posts, and rushing it means the post shifts inside six months on this clay. A typical install is one to three days on site plus two to three days for the concrete to reach enough strength. Same-day work is a repair-only promise. For an install, call (469) 530-2485 and we will set a measured timeline.
Yes. In Texas, an automatic gate has to meet UL 325, which means working safety photocells or edge sensors plus a verified reversal on contact. We test the reversal in front of you before we close the job, and if the gate fails, we do not leave it running automatically. Call (469) 530-2485 if you are not sure what your existing gate has.
Yes, we convert swing gates to slide gates in Atascocita when the driveway slope or the setback supports it. A slide gate needs a flat run of track or a cantilever setup, plus a different operator and a new footing detail for the clay. It runs $4,200 and up here. We will tell you honestly if your driveway will not take a slide gate before you spend anything.
We install and service Linear, Viking, Ghost Controls, and DoorKing operators, plus LiftMaster, FAAC, BFT, and Mighty Mule. For Atascocita we keep Linear and Ghost Controls parts in stock, so a board failure does not leave your driveway open for a week.
If the leaves are level and the hinges look tight but the operator strains or throws faults, it is usually the panel, hinges, or the operator itself. If the gate has dropped at the latch side or drags at the bottom corner, the post has moved and you are looking at a footing re-set, not a panel adjustment. Call (469) 530-2485 and we will tell you which one it is before quoting anything.
Call Carver Gate Repair in Atascocita
Before you order a gate or sign with a general contractor, get a written price from a crew that only does gates. Call (469) 530-2485 for a free estimate. We will measure, quote, and set a schedule. If it is not right after we install it, the 365-Day Done Right Promise covers it. Lonnie Burke and the crews are ready.
Written by Lonnie Burke, Owner at Carver Gate Repair, serving Atascocita with gate installation and repair since the company’s founding in 2008.