Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Jacksonville
Gate repair in Jacksonville usually comes down to two things: a gate that won’t open, or a gate that won’t stay where it should. Most calls we run across Duval County are fixable in a single visit, typically $180 to $625 for common mechanical failures, and $275 to $650 when a motor or circuit board is involved. We know the neighborhoods, the soil, and the specific way Jacksonville gates fail. If yours is stuck, dragging, or refusing to reverse, call (469) 530-2485 and a real person answers, day or night.
Why Carver Gate Repair Is Jacksonville’s Preferred Gate Repair Company
Homeowners in Jacksonville call us because we do one thing: gates. Not fences, not general contracting. Our Gate Repair team works on swing gates, slide gates, and the automation that drives them. Every Carver technician is background-checked and arrives in uniform. You know who you’re letting through the gate.
We run on The Garrison Standard: a written price before any work starts, and a written guarantee on every repair, good for a full year. That guarantee isn’t a marketing line. If the repair fails inside 365 days, we come back free and make it right. No charge, no argument.
Lonnie Burke leads our Jacksonville operation. He’s built the crew around one idea: a gate repair company should answer the phone, show up on time, and leave the job site cleaner than we found it. That’s what Jacksonville customers tell us they were missing before they found us.
Iron Gate Repair in Jacksonville
Iron gate repair in Jacksonville usually means resetting a pivot point, rebuilding a hinge post, or straightening a panel that’s sagged into the driveway. Wrought iron and steel gates here take a beating from summer humidity and salt air near the river and coast. The gate frame itself may look fine while the bottom hinge post anchor rusts out underground, which throws the whole gate off level.
Hinge and Post Rebuilds
When a Jacksonville iron gate drags, the problem is often the footing, not the hinge. Wet soil holds moisture against the anchor plate and bottom post, corroding it from the ground up. We dig out the old footing, reset the post in fresh concrete, and remount the gate so it swings true.
Rust Repair and Structural Welds
Surface rust on iron gates is common in Jacksonville, especially in Riverside, San Marco, and Ortega, where mature trees shade the metal and keep it damp longer. For cracked pickets or broken scrollwork, we grind and weld the joint, then coat it to match the surrounding finish.
Sliding Gate Repair in Jacksonville
Sliding gate repair in Jacksonville typically involves the track, the rollers, or the rack-and-pinion gear that moves the gate. Slide gates are popular here because they don’t swing into a driveway and they handle long runs well. But flat lots and frequent rain mean the track collects debris, and if the footing shifts even a quarter inch, the gate binds halfway through its travel.
Track Realignment and Roller Replacement
A homeowner in Riverside called about a 12-foot slide gate that dragged and stuck halfway. Our tech found the rack and pinion misaligned and the concrete post footing shifted from saturated soil. We reset the footing, realigned the gear rack, and re-leveled the track. Then we replaced a corroded LiftMaster gate operator limit switch and tested the safety photocell and reversal. The gate has opened smoothly since.
Operator and Limit Switch Repairs
Slide gate operators in Jacksonville accumulate moisture inside the housing after heavy summer rains. That shorts limit switches and control boards. If the gate opens but won’t stop at the right point, or slams at the end of travel, the limit switch is usually the culprit. We replace the switch, seal the housing, and retest the travel limits.
Trusted Brands We Service in Jacksonville
We work on the gear already installed at your house. Our technicians carry parts and know the failure patterns for Linear, Viking, Ghost Controls, and DoorKing operators, among others. That means we don’t show up, look at your opener, and tell you we only service the brand we sell. We service what’s on your post, and we keep common parts on our trucks in Jacksonville so most motor repairs finish the same day. When a board or gear set needs to be ordered, we give you the timeframe in writing before we touch a wrench.
Common Gate Repair Problems We See in Jacksonville Homes
- Sagging swing gates. Jacksonville’s low water table and heavy summer rains keep gate post footings wet, so concrete anchor plates and bottom hinge posts rust or loosen from the ground up long before the gate’s metal frame fails. A gate that scraped at the latch for a year was probably failing at the footing, not the hinge.
- Slide gate jams after rain. Yard debris and silt wash into the track during downpours, and saturated soil under the track shifts. The gate runs a few feet, then brakes or throws an obstruction code.
- Safety photocell or edge sensor failure. Moisture works its way into sensors and photocells mounted close to the ground. The gate runs fine, but it won’t reverse when something blocks it, which is a UL 325 entrapment protection problem and a real safety issue for kids and pets.
- Chain-drive and belt-drive slippage. In humid air, chains on older slide gate operators stretch and rust at different rates. The gate jerks, slips, or stops mid-cycle and flashes an error.
Pricing for Gate Repair in Jacksonville, FL
What you pay depends on what failed and how long it takes to make right, but you’ll know the number before we start. Here are the ranges we see across Jacksonville, from Orange Park to Atlantic Beach:
| Service | Typical Jacksonville Range |
|---|---|
| Hinge or post reset and remount | $225 – $480 |
| Track realignment, slide gate | $180 – $350 |
| Limit switch replacement | $150 – $275 |
| Safety photocell or edge sensor repair | $140 – $310 |
| Gate operator motor replacement | $425 – $900 |
| Rust repair and welded joint (per section) | $110 – $300 |
Everything is on paper before we begin. The price we quote is the price you pay. Estimates are free. Call (469) 530-2485 and we’ll give you a number we’ll stand behind.
We Also Serve Cities Near Jacksonville
Our Jacksonville crews cover the metro and the surrounding counties. Gate Repair in Jacksonville extends to Orange Park and Fleming Island in Clay County, Middleburg to the southwest, and Atlantic Beach out toward the coast. If you’re within a 45-minute drive of downtown Jacksonville, we can put a technician at your gate.
Serving Jacksonville, FL – Our Local Coverage Area
We’re based in the Jacksonville area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Jacksonville
The most common reason is a loosened or rusted hinge post anchor in wet Jacksonville soil, not a worn hinge itself. The post shifts or rots below ground level, the gate tilts forward, and the latch side drags. We reset the post, remount the gate, and it swings clean again. If yours is dragging, call (469) 530-2485 and we’ll tell you whether it’s the post or the hinge before we quote anything.
No. Installation of a new automatic gate is measured, ordered, and scheduled. It includes groundworks, concrete footings, the gate itself, motor, safety edges, and reversal testing. We give you a free site measure and a written price, then schedule the work around your timeline. We don’t rush an install and we don’t pretend it’s a two-hour job. Call (469) 530-2485 to set up a measure.
Heavy rain in Jacksonville washes silt and debris into the track and saturates the soil under the track footing. The gate then binds as the track shifts or fills with mud. The operator isn’t usually the failure; it’s tripping its obstruction sensing because the gate physically can’t travel freely. We clear the track, reset the alignment, and often replace the rack if rain has rusted the teeth. Call (469) 530-2485 and we’ll diagnose it on site.
Yes. Automatic gates in Jacksonville must meet UL 325 entrapment protection standards, which means working safety photocells or edge sensors and a tested auto-reverse function. If your gate runs but doesn’t reverse when it hits an obstruction, it’s out of compliance and dangerous. We test and replace failed sensors as part of every gate motor repair. Call (469) 530-2485 if your gate isn’t reversing the way it should.
First, check that the photocell lenses are clean and aligned, then check that the edge sensor isn’t cracked or waterlogged. If both look fine but the gate still won’t reverse, don’t keep testing it against a person or pet. Have a technician check the control board and sensor wiring. In Jacksonville, moisture in the sensor housing is a frequent cause. Call (469) 530-2485 and we’ll test the full entrapment protection system, not just the part that’s easiest to reach.
Contact Carver Gate Repair in Jacksonville
If your gate is down, dragging, or behaving like it has a mind of its own, call (469) 530-2485. A live person answers around the clock. We’ll schedule a background-checked, uniformed technician to your home in Jacksonville, give you a written price before anything is opened up, and back the repair with a 365-Day Done Right Promise. That’s The Garrison Standard, and it’s the only way we work.
Written by Lonnie Burke, Owner at Carver Gate Repair, serving Jacksonville, FL and the surrounding metro.