Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Westminster
Gate repair in Westminster usually falls into two buckets: a mechanical failure (hinge, post, weld, wheel) or an electrical failure (operator, board, limit switch, photocell). Most repair calls we run in Westminster are diagnosed and fixed in a single visit, and a typical service call runs between $75 and $185 for the diagnostic, with the repair itself quoted in writing before we touch a single bolt. If you live off Bolsa Avenue, in the tract neighborhoods south of Westminster Boulevard, or near the Westminster Mall, our crews know the housing stock and the common gate types. Call (469) 530-2485 and a live person in the Los Angeles office will answer, 24/7.
Why Carver Gate Repair Is Westminster’s Preferred Gate Repair Company
Homeowners in Westminster call us because the way we run a job matches how they want to run their homes: a written price before work starts, a technician who arrives in uniform and is background-checked, and a guarantee that is written down, not spoken. Lonnie Burke oversees the work and holds every job to The Garrison Standard. That standard has one rule that matters more than any other: if it’s not done right, we make it right, for a full year, at no charge for the second visit.
We work exclusively on gates and gate motor systems. That focus means we do not treat a gate repair as a side job between fence installations. We replace hinge posts, rebuild operator control boards, align photocells on sliding gates along Westminster’s busy streets, and re-hang sagging double swing gates on original tract-home side yards. Our Westminster customers do not chase us for callbacks. We dispatch from the Los Angeles office and serve Westminster directly.
The reviews from Westminster homeowners focus on two things: the technician showed up when promised, and the price did not move. That is the entire job, in our view. Written quote. Clean site. One visit. A gate that stays working.
Wrought Iron Gate Repair in Westminster
Wrought iron gate repair in Westminster is one of the most common services we provide, and the failure points are predictable. Original wrought iron gates on mid-century tract homes were well built, but after 40 or 50 years the hinge posts have often rotted below the concrete line, the latch side has sagged, and weld joints have fatigued where the pickets meet the bottom rail. A typical wrought iron gate repair in Westminster runs $250 to $800, depending on whether we are re-welding a cracked joint, re-hanging a leaf that has dropped, or excavating and replacing a post.
Hinge Post Replacement and Sag Correction
The acid test for a wrought iron gate in Westminster is whether the latch still aligns. If you have to lift the gate to close it, the hinge post has moved. We excavate the old footing, pour a new concrete pier, reset the post plumb, and re-hang the leaves using weld-on hinges. On double gates, we add a sag correction brace to the leaf that has dropped. This is structural work, not cosmetic, and it has to hold for decades.
Weld Repair and Rust Treatment
Westminster’s fog and coastal air mean wrought iron rusts faster than people expect, especially at the base of the gate where irrigation water splashes against the rails. We grind out cracked welds, re-weld with proper penetration, reinforce the failed section, and treat the rust with a converter and a rust-inhibiting primer before touching up the paint. A repaint is never a substitute for addressing the steel underneath.
Metal Gate Repair in Westminster
Metal gate repair in Westminster covers steel tube-frame gates, aluminum drive gates, and fabricated metal yard gates. The repair itself depends on what the gate is made of and how it failed. A bent steel frame from a car bump in a tight Westminster driveway might be straightened and re-welded; an aluminum gate with a cracked weld at the corner needs a gusset plate; a steel gate that has rusted through at the bottom rail needs that rail cut out and replaced. Typical metal gate repair in Westminster runs $300 to $950 for most structural work and $150 to $400 for alignment and hinge replacement.
Gate Realignment and Frame Straightening
Metal gates go out of square for a reason: a hinge loosened, a post settled, a wheel wore flat, or someone backed into it. We measure the opening, check the diagonals, and identify which corner has moved before we clamp and straighten. Straightening without fixing the root cause means the same bend returns in six months.
Lock and Latch Repair Replacement
A gate that has sagged puts extra load on the lock. We often find the latch plate worn to a knife edge, the lock cylinder stripped, or the keeper bracket broken off the post. We repair or replace the lock hardware after the gate alignment is corrected, so the new lock doesn’t chew itself up against a misaligned striker.
Trusted Brands We Service in Westminster
Our Westminster technicians work on nine gate-motor brands, including LiftMaster, Linear, Viking, and DoorKing. When a control board fails, we do not sell you a whole new operator just because the board is out of stock; we carry or source the right board and rebuild the operator around it. For Westminster customers, that means less wait time and no paying for a “system upgrade” that was never discussed on the phone.
Common Gate Repair Problems We See in Westminster Homes
- Rotted hinge posts from shallow concrete. Most original Westminster tract-home side gates were set in a 12-inch concrete plug that cracked within 20 years. Clay soil expands and contracts with the seasons, and the post moves. We see this on gates in the neighborhoods east of Beach Boulevard and south of 405.
- Burned-out control boards in aging LiftMaster and Linear operators. Operators from 10 to 15 years ago have capacitors on the board that dry out and leak. A power surge from an ungrounded garage outlet finishes the job. The gate then buzzes, clicks, or does nothing.
- Misaligned photocells on Bolsa Avenue slide gates. Traffic vibration on Bolsa Avenue works the photocell brackets loose over time. The gate reverses for no reason, or every time a car drives by, because the beam is bouncing off the reflector guard.
- Dragging double swing gates on original side yards. Clay soil movement and decades of rain have settled one or both hinge posts. The latch side sinks, the top rail sags, and the operator starts tripping its force sensor every time it opens.
Pricing for Gate Repair in Westminster, CA
Gate repair in Westminster, CA comes with price ranges we’ll stand behind.
- Service call / diagnostic: $75 – $185, waived toward the repair if we do the work.
- Hinge replacement and gate re-hanging: $250 – $600 per leaf.
- Hinge post excavation and concrete re-set: $500 – $1,200, depending on access and soil.
- Operator control board replacement: $350 – $900, brand- and model-dependent.
- Photocell replacement or realignment: $150 – $350.
- Weld repair with rust treatment: $200 – $500 per section.
The price you’re quoted is what you pay. It’s written, it’s yours to keep, and we agree on it before any work starts. Free estimates by phone or on site. Call (469) 530-2485.
We Also Serve Cities Near Westminster
Our crews serve Westminster and the surrounding area, including Midway City, Huntington Beach, Stanton, and Fountain Valley. If you are just outside these cities, call the office and we will tell you straight whether we can get a technician to you. We’re the Gate Repair team homeowners in Westminster call for straight answers.
Serving Westminster, CA – Our Local Coverage Area
We’re based in the Westminster area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Westminster
Yes. If your gate reverses as it closes, or refuses to close at all, the most common cause is a misaligned or obstructed photocell. Slide gates on busy Westminster streets like Bolsa Avenue get vibrated out of alignment. Check that both cell lenses are clean and facing each other, then call us if the problem persists. We can realign, reconnect, or replace a failed cell on the first visit. Call (469) 530-2485 and we’ll walk you through it.
One full day, usually. We excavate the old footing, pour a new concrete pier, set the post plumb, and let the concrete cure before re-hanging the gate. In some Westminster yards with tight access we have to hand-dig and hand-mix, which adds time but no surprises to the written price. The gate is secured at the end of the day, even if the concrete needs a few more hours to fully cure.
Yes. We carry parts for LiftMaster and FAAC operators, along with Linear, Viking, DoorKing, Ghost Controls, BFT, and three other brands. Our technicians are trained on the electronics, the limit switch logic, and the entrapment protection on each brand. In Westminster, a failed LiftMaster board is usually a same-visit replacement if the part is in the truck.
That behavior is almost always a photocell issue, a bad capacitor on the control board, or a worn limit switch that has drifted. When the gate reverses mid-travel, the operator thinks something is in the beam or the drag sensor has tripped. We test each component with a meter and replace only what failed.
Yes, both. We install keypads, intercoms, and card readers on single and double swing gates, and we mount solar gate openers where running a power line would mean crossing too much concrete or trenching through existing landscape. For solar in Westminster, we position the panel for maximum southern exposure and verify charging voltage under load before we leave.
For gate repair in Westminster, CA, call (469) 530-2485. A written quote, a real person on the phone, and a full-year guarantee on every repair. We’ll tell you what’s wrong, what it costs, and how we’ll fix it.
Written by Lonnie Burke, Owner at Carver Gate Repair, serving Westminster since 2008.