Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Silverdale, WA
Carver Gate Repair is the gate company Silverdale homeowners call when a gate stops opening, a motor burns out, or a new gate needs to be measured and installed right the first time. Most of the gates here swing or slide on hardware that’s been through years of Puget Sound damp and salt air, which means we see rust, swollen hinges, and control boards corroded long before the motor itself fails. If you need a repair, an install, or a motor diagnosis, call (469) 530-2485 and you’ll get a live person. We quote a written price before any work starts, and every repair carries our 365-Day Done Right Promise in writing. Silverdale has three dedicated service pages that cover the work in detail: gate repair, gate installation, and gate motor repair.
Why Silverdale Homes Are Different
Silverdale sits at the top of Dyes Inlet, where moist marine air pushes in from the sound and settles on gate hardware year-round. That’s the single biggest variable we account for here. A steel gate in Silverdale isn’t just dealing with rain; it’s dealing with salt-laced humidity that gets into pivot points, hinge welds, and motor housings. We regularly open control boxes on gates near Clear Creek Road and find circuit boards with green corrosion on the terminals, even inside supposedly weatherproof enclosures. The fix isn’t always a new board. Sometimes it’s cleaning the contacts and rerouting the conduit so water stops following the wire into the enclosure.
The second variable is the terrain. Many Silverdale lots slope, especially the older ones east of Silverdale Way and up toward the neighborhoods around Ridgetop, where a gate may sit at the bottom of a short, steep driveway. A swing gate on a slope puts lateral load on the hinge side in a way a flat-lot gate never does, which is why we pay extra attention to hinge post footing and whether the post itself has started to lean. That lean is usually the first sign the gate will start dragging or, worse, binding the motor. High-tension springs and heavy gate panels are involved in much of this work. We recommend a trained technician handle any repair where the gate weighs more than about 150 pounds; the stored energy in a wound spring can cause serious injury if released incorrectly.
Our Main Silverdale Services
Silverdale homeowners call us most often for two things: a gate that has stopped working and a motor that has stopped working. Sometimes those are the same call. Each service has its own Silverdale page so you can see exactly what’s covered, how we price it, and how the warranty applies.
Gate Repair in Silverdale
Gate repair in Silverdale typically means a sagging or dragging gate, a hinge that’s pulling away from the post, or a latch that no longer closes cleanly. One job we see often in the older neighborhoods west of the mall: steel frames rusted through at the bottom rail, where standing water from weeks of drizzle sits against the weld. We cut out the rusted section, weld in a new rail, and repaint the joint before it fails completely. The full breakdown of what we repair, what it costs, and how the 365-Day Done Right Promise works is on the Gate Repair in Silverdale page. If the gate will not move at all, call us; we’ll diagnose it before we quote it.
Gate Installation in Silverdale
A new gate installation in Silverdale starts with the driveway and the ground it sits on. We do not sell a gate without looking at the slope, the soil, and where the post holes need to go. If the ground is soft or the driveway has a crown, the post depth and footing change. That’s a written, measured conversation, not a guess. The Gate Installation in Silverdale page covers the process: how we measure, what brands we install, how long a typical install takes, and what a free measure and written price looks like before you commit to anything.
Gate Motor Repair in Silverdale
Gate motor repair in Silverdale is usually one of three things: a bad limit switch, a failed capacitor, or a control board that got wet. We carry parts for the major motor brands and diagnose on site. If a motor is beyond repair, we’ll show you the replacement cost in writing before touching the old one. The Gate Motor Repair in Silverdale page breaks down repair versus replacement pricing, the symptoms we see most in Silverdale’s damp climate, and the written guarantee that covers the work for a full year.
What happens when you call
- 1
A real person answersNo phone trees – you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Silverdale
Our technicians work on Viking, Ghost Controls, DoorKing, and Elite systems, among others, and we stock common parts for those brands in our Silverdale service vehicles rather than ordering every part after the first visit. Our brands page lists the full range of equipment we service and what we keep on hand.
Pricing for Gate Company in Silverdale, WA
| Service | Typical range in Silverdale |
|---|---|
| Gate repair, minor (hinge adjustment, latch fix) | $150 – $350 |
| Gate repair, moderate (welded rail, post straightening) | $350 – $800 |
| Gate repair, major (structural failure, full re-hang) | $800 – $1,800 |
| New gate installation, single swing | $2,500 – $5,500 |
| New gate installation, double swing | $5,000 – $9,000 |
| New gate installation, sliding gate | $6,500 – $12,000 |
| Gate motor repair (limit switch, capacitor) | $200 – $450 |
| Gate motor replacement, swing operator | $900 – $2,200 |
| Gate motor replacement, slide operator | $1,400 – $3,000 |
| Control board replacement | $350 – $800 |
| Loop detector replacement | $300 – $700 |
In Silverdale, prices push upward when salt-air corrosion has moved beyond the surface, when a post has to be dug out and reset in concrete, or when the gate is on a steep slope that requires additional bracing. When we quote a job, the price is written down and agreed before any work begins. That number does not change at the door.
Neighborhoods We Serve in Silverdale
We run calls across the whole Silverdale area, from the older streets east of Silverdale Way to the newer developments up toward Ridgetop and the neighborhoods around Clear Creek. Most residential repairs are dispatched inside a single day, and we schedule installs by appointment with a written price before the job day.
- Silverdale Way corridor
- Clear Creek Road area
- Ridgetop neighborhoods
- Old Town Silverdale
- Bucklin Hill Road areas
Service Area – Cities Near Silverdale
Carver Gate Repair handles gate work across Kitsap County. When a Silverdale customer refers us to family or a neighbor nearby, we often end up running a gate motor diagnostic in Poulsbo, WA, replacing a swing hinge in Tracyton, WA, or quoting a new gate in Bremerton, WA or Manchester, WA. The same Garrison Standard applies everywhere: written price first, background-checked technician, and a written guarantee on every repair.
Serving Silverdale, WA – Our Local Coverage Area
We’re based in the Silverdale area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Silverdale
Most residential gate repairs in Silverdale are reached the same day you call, or the next morning at the latest. We keep parts for common motor brands on the truck, so a limit switch or capacitor doesn’t mean a second trip. Call (469) 530-2485 and a live person will give you an honest arrival window.
It depends on the scope. A like-for-like gate or motor swap rarely needs a permit. When posts are being set deeper, or when the gate is part of a required enclosure, Kitsap County may require one. We’ll tell you what applies to your property before the quote, not after the job starts. Call (469) 530-2485 with your address and we’ll look at it.
Yes. We work with homeowner associations on shared entry gates, and we know the difference between a gate that serves one home and one that serves thirty. HOA gates need documentation, written quotes the board can review, and work scheduled around access hours. Call (469) 530-2485 and ask for Lonnie Burke; he’ll walk you through what the board needs to see.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Silverdale Customers Say
"Showed up a little after the window, but he called ahead. On time otherwise, polite, and efficient. Cleaned up all the tools."
- Joan K."Swing gate arm snapped. They replaced the actuator and tested the safety reverse. Fair price."
- Angela P."Keypad and remotes set up fresh for the whole neighborhood. Done cleanly and quickly."
- Chris W.