Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Arlington
Gate installation in Arlington runs between $2,800 and $9,500 for most homes, depending on gate type, length, motor choice, and what the soil under the posts requires. A standard single swing driveway gate with a chain-driven operator typically lands in the $3,200 to $5,400 range. We schedule a free measure and written quote within a few days, then install on a set date with a fixed price agreed before any material arrives. Call (469) 530-2485 and a live person answers, any hour.
Arlington’s Blackland Prairie clay changes how gates need to be set. The soil swells in wet springs and shrinks in dry summers, and posts that are not dug deep enough will move. We plan for that on every job because gates in Arlington don’t fail from the gate itself. They fail from what is underneath it.
Why Carver Gate Repair Is Arlington’s Preferred Gate Installation Company
Homeowners around Arlington call us after a gate has already failed once. The post leans, the operator binds, or the gate drags on the driveway. A lot of the time the original install was fine for another soil type. Our crews dig for Arlington’s clay, not a generic spec. We set posts deeper and flare the concrete at the bottom so the clay cannot jack them out during the wet-dry cycle.
Every installation follows The Garrison Standard, which has been the operating rule for the Garrison Partners family since 2008. That means a written price before work starts, a background-checked and uniformed technician on site, and a written 365-Day Done Right Promise on every install. If something is not right within a year, we come back and fix it. No charge, no argument.
Lonnie Burke runs the crews to that standard. When you call, you get a live person. When the technician arrives, you know who they are before they step onto the property. We work on gate systems across Arlington, from the older subdivisions near Fielder Road and Pioneer Parkway to the newer builds south of I-20 near Mansfield.
Driveway Gate Installation in Arlington
Driveway Gate Installation in Arlington is the most common project we take on, and the one most affected by local soil and lot drainage. The job means setting hinge and latch posts, hanging the gate, running power to the operator, and installing the safety sensors UL 325 requires. A single swing gate on a flat Arlington lot runs $3,200 to $5,400 installed with a standard operator. A double gate on a sloped driveway, where the low side needs extra post depth, runs $5,500 to $8,900.
Arlington homeowners typically need a driveway gate when they want to close off rear access, keep vehicles controlled, or secure a side entrance for trailers and equipment. The clay under the driveway is the variable that matters most. Our estimate includes what the soil requires, not just what the gate costs.
Footings Set for Arlington Clay
We dig deeper here than a contractor would in sandy soil. The active clay zone shifts with moisture. We set posts below that zone and bell the concrete at the bottom. It is slower work and it is the reason the gate stays plumb through wet springs and dry summers.
Operators and Safety Systems
Every automatic driveway gate gets photo-eyes or edge sensors installed and tested. UL 325 requires entrapment protection, and we set the reversal force at the slab edge before the job closes. That is not a line item you should accept being skipped.
Sliding Gate Installation in Arlington
Sliding Gate Installation in Arlington works best on lots where the driveway slopes toward the street or there is no room for a gate to swing inward. A sliding gate rides on a track or cantilever rail, so the foundation under the track has to hold straight while the clay around it moves. A standard 12-foot sliding driveway gate with a rack-and-pinion operator runs $3,800 to $7,200 in Arlington. A longer gate or a cantilever system that avoids a ground track runs higher, $6,500 to $9,500.
We see these on larger Arlington properties, especially along the streets running toward Lake Arlington and the neighborhoods with longer setbacks. Standing water at the gate line rusts the rack and pinion and shorts control boards, so we grade the base and keep the track clear of the drainage path. The power run gets a dedicated circuit, not a tap off an existing outlet.
V-Groove Track and Rack Alignment
The rack and pinion alignment is what makes a sliding gate quiet and reliable. If the track heaves even an inch, the gate grinds and the motor loads up. We set the base for Arlington’s soil movement, not just today’s level.
Cantilever Gates for Mud-Line Lots
On properties where the gate line holds water after a hard rain, we push for a cantilever design. The gate rides on rollers above the ground instead of a track in the mud. It costs more up front and it eliminates the most common sliding gate failure we repair in Arlington.
Trusted Brands We Service in Arlington
Our crews install and service FAAC, BFT, Linear, and Viking operators alongside LiftMaster, Ghost Controls, and Mighty Mule. Carver Gate Repair is the gate specialist for the Garrison Partners family, and we keep common control boards, limit switches, and loop detectors stocked for Arlington jobs. When a Viking operator on a sliding gate off Park Springs Boulevard goes down, we are not waiting a week on a part. The right brand gets matched to the system already on the property, and the technician knows how it is supposed to behave. That matters on older Arlington homes where the gate may have been through two or three operators already.
Common Gate Installation Problems We See in Arlington Homes
- Post heave from expansive clay. Arlington’s Blackland Prairie clay swells in the spring and shrinks in August. Shallow posts move, the hinge side drops, and the gate drags or the operator binds. We dig below the active zone and bell the footing so the post cannot jack out.
- Missing or bypassed entrapment protection. UL 325 requires photo-eyes or edge sensors on every automatic gate. We still find installs where the wires were never connected. A reversing gate on a driveway can pin a person or crush a car. We test reversal force and sensor coverage on every installation we complete.
- Drainage pooling at the gate line. Lots across Arlington slope toward the street, and the gate line often sits in the low spot. Standing water rusts racks, kills control boards, and softens the soil around posts. We grade the base and route drainage around the operator.
- Operators matched to the wrong gate weight. A heavy steel gate on an undersized operator fails early. We size the motor to the actual gate weight and cycle count, and we do not install a residential opener on a gate that runs dozens of times a day.
Pricing for Gate Installation in Arlington, TX
Most single swing driveway gates in Arlington run $3,200 to $5,400 installed with a chain-driven operator. Sliding gates run $3,800 to $7,200 for a standard track system. Double gates run $5,500 to $8,900. A basic pedestrian gate with a mechanical lock starts around $2,800. Operators from FAAC or Viking add $900 to $2,400 depending on duty cycle and safety system requirements.
The price on the quote is the price on the invoice. We deliver a written estimate after measuring the gate line, checking soil conditions, and confirming the power run. Every number is set before work starts, and the 365-Day Done Right Promise is in writing on every installation. Call (469) 530-2485 for a free estimate. We do not charge for the measure and the quote.
We Also Serve Cities Near Arlington
Our crews work across the Arlington area, and we handle Gate Installation in Mansfield, Kennedale, Burleson, and Cedar Hill. If you are in one of those cities, the same Garrison Standard applies: written price first, background-checked technician, full-year guarantee. For gate work specific to this city, see Gate Installation in Arlington or call (469) 530-2485 to get on the schedule.
Serving Arlington, TX – Our Local Coverage Area
We’re based in the Arlington area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Installation in Arlington
Arlington sits on Blackland Prairie clay, which swells when wet and shrinks when dry. A post set in shallow concrete will rise during the spring rains and settle in the summer, pulling the gate out of alignment or racking the operator. We dig deeper post holes, bell the concrete at the bottom, and set the footing below the active clay zone. That is the single most important difference between a gate that lasts here and one that leans in a year. Call (469) 530-2485 if your gate post is already leaning; we can assess it and quote a fix.
Yes. UL 325 requires every automatic gate in the United States to include entrapment protection, which means photo-eyes, edge sensors, or both. Arlington is no exception. We install and test photo-cell beams and reversal force on every gate we put in, and we check existing installs for bypassed sensors. A gate without working sensors can crush a person or vehicle, and the liability sits with the property owner. We will not install an automatic gate without the safety system complete and tested.
No. A proper gate installation in Arlington requires measuring the gate line, digging and setting footings for the clay, running power, hanging the gate, and testing the operator and safety system. We do not rush that work or promise a same-day turnaround. We schedule a free measure within a few days and then set an installation date with a written price agreed before materials arrive. If you have a failed gate that needs emergency attention, we can often send a technician to secure the opening while the replacement is planned. Call (469) 530-2485 and we will tell you the honest timeline.
We install FAAC, BFT, Linear, and Viking operators, plus LiftMaster, DoorKing, Elite, Ghost Controls, and Mighty Mule. The right choice depends on gate weight, cycle count, and whether the gate is swing or sliding. We match the operator to the gate and the usage, not to whatever is on the truck. If you already have a brand on the property, we can often keep it and upgrade the board or motor rather than replacing the whole system. Estimates are free, and the quote covers the full install.
A real quote starts with a site measure. We check the gate line, the slope, the drainage path, and the soil where posts will go. Then we price the gate, the post footings, the operator, the power run, and the UL 325 safety system. In Arlington that usually means deeper footings and possibly drainage work at the base. The quote is written and fixed before work starts. Call (469) 530-2485 to schedule a free measure, and you will have a number in writing, not a range that moves at the door.
One more thing worth knowing about Arlington specifically. We installed a 16-foot steel swing gate for a homeowner off Green Oaks Boulevard near the Rush Creek greenbelt. The original gate had pulled its hinge post out of the clay after two wet springs. We dug bell-shaped footings below the active clay zone, set the post in concrete, hung the gate, then mounted a LiftMaster operator and tested the safety photocell beam and reversal at the slab edge before we called the job done. The gate has held plumb through two full clay cycles since. That is what a proper install here requires, and it is the standard we apply to every Arlington gate we touch.
Written by Lonnie Burke, owner of Carver Gate Repair, serving Arlington under The Garrison Standard since 2008.