Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Garland
A new driveway gate in Garland typically costs $2,800 to $9,500 installed, depending on the gate type, operator, and ground conditions. Most single swing gate installations here run $3,200 to $5,800 with a quality operator included. Sliding gates and double swing gates land higher, usually $5,500 to $9,500, because they need more steel, more ground work, and heavier operators. We serve all of Garland, from Firewheel to Duck Creek to the neighborhoods off Broadway and Buckingham. Call (469) 530-2485 and we’ll give you a written price before any work starts. Not an estimate that moves at the door. A written price.
Why Carver Gate Repair Is Garland’s Preferred Gate Installation Company
Garland homeowners tend to call us after getting burned once. They hired a generalist who showed up late, quoted one number, and left a bill for another. Or paid someone to straighten a sagging gate, only to watch it drag again six months later because nobody fixed the footing underneath it. That second call is where we start most Garland jobs: finding the actual cause, not patching the symptom.
Our crews work to The Garrison Standard, which the Garrison Partners family has run since 2008. That means every technician is background-checked and uniformed, so when someone pulls up to your house near Naaman Forest or Walnut Creek, you know exactly who you’re letting through the gate. Every job gets a written price before work begins. Every installation carries a 365-Day Done Right Promise in writing. If it’s not right, we make it right. If a repair fails inside the guarantee year, the second visit is free. No charge, no argument.
Phones are answered by a live person, 24 hours a day. You call at 2 a.m. because a gate motor is dead and a car is stuck in the driveway, a real person picks up and starts the dispatch. That matters in Garland, where half of the year the heat is punishing and nobody wants to spend a morning waiting on a no-show.
Gate Fabrication in Garland
Gate Fabrication in Garland is a different job from bolting a pre-made panel onto posts bought from a big-box store. Most Garland properties with driveway gates need custom fabrication because the opening widths, driveway slopes, and set-back distances vary from house to house. A gate built for a flat lot in Richardson will not fit correctly on a sloped driveway off Belt Line Road. We fabricate to the opening, not from a template.
Steel Frame and Panel Build
We build gates from steel tube and channel, welded and braced at the corners rather than just bolted. A properly welded steel frame holds its square over years of Garland heat and the occasional hailstorm. We size the gate to the opening with a tolerance for expansion and ground movement, because clay soil does not stay put here. The cost for a fabricated single swing gate in Garland, powder-coated and mounted, usually comes in between $3,500 and $6,800 depending on height, width, and finish.
Posts and Footings Set for Garland Soil
The hinge post is the part that fails most often in Garland, and it almost always fails because it was set too shallow. Our standard is to pour footings deeper than code minimum, set in concrete below the active clay zone, so the post doesn’t heave with the seasonal wet-dry cycle. A new steel post with a proper footing adds $800 to $1,500 per post, and it is the difference between a gate that still swings true in five years and one that drags by fall.
Automatic Gate Installation in Garland
Automatic Gate Installation in Garland refers to the full system: the operator mounted and wired, safety photocells and edge sensors set correctly, and the gate travel tuned so it opens and closes smoothly under load. This runs $2,200 to $4,800 on top of the gate itself, depending on the operator brand and whether the run is a swing arm, a slide track, or a ram. On a standard single driveway gate, the automation portion usually accounts for about half the total job cost.
Dedicated Power and Operator Mount
A Garland automatic gate needs its own circuit. We never wire an operator into an existing landscape lighting line, because the breaker will trip the first time the outdoor lights and the gate cycle together. We run a dedicated circuit, mount the operator on a reinforced pad or post, and set the limits so the gate stops cleanly instead of slamming the stop or stalling mid-travel. This is table stakes for a reliable install.
Safety Edges, Sensors, and Reversal Testing
Every automatic gate installed in Garland gets a full entrapment-protection setup. Photocells and edge sensors go at the correct height, aimed so afternoon sun does not trigger phantom reversals, which we see constantly on gates installed by generalists who aimed sensors across a west-facing driveway. We test the reversal force twice before we leave: once with a gauge, once by hand at the leading edge. UL 325 compliance is not optional on an automatic gate, and we treat it that way.
Trusted Brands We Service in Garland
The operator you choose matters as much as the gate. We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems, so we match the operator to the gate weight, cycle frequency, and power situation rather than selling whatever is on the truck. If you already have a FAAC or BFT operator on a failing gate and want to keep it, we can often rebuild the mount and re-tune the travel instead of forcing a full replacement. If you need a new operator, we carry or can source Linear and Viking units quickly, which keeps installations in Garland moving without a two-week part wait.
Common Gate Installation Problems We See in Garland Homes
- Shallow hinge posts in Blackland clay. Garland’s soil expands in wet springs and shrinks in dry summers. A post set at the code minimum or bolted to a slab will shift within a season, and the gate will sag or bind even if the panel is perfectly straight.
- Operators on shared lighting circuits. We see automatic gates wired into landscape lighting transformers all over Firewheel and the older streets near downtown Garland. The breaker trips the first time both loads cycle together, and the homeowner assumes the operator is defective.
- Sensors aimed across the driveway at the wrong height. Afternoon sun hits west-facing sensor beams in Garland and causes the gate to reverse mid-cycle, or refuse to close. The owner blames the operator; the real problem is sensor placement and aiming.
- Gates built for flat lots installed on sloped driveways. Several Garland neighborhoods near Duck Creek and along Miller Road have pronounced driveway slopes. A gate fabricated without accounting for that grade will drag at the low end or stick at the high end before the operator even wears in.
Pricing for Gate Installation in Garland, TX
A single swing driveway gate in Garland, fabricated and installed with a quality operator, typically runs $4,800 to $7,500 all-in. That includes the gate, steel posts with deep footings, an operator on a dedicated circuit, and full safety edge and photocell mounting with reversal testing. A pedestrian gate runs $1,200 to $2,800. A double swing or sliding gate, which needs more steel, heavier operators, and often a track or rack, runs $6,500 to $9,500. What moves the number: gate width, driveway slope, whether the post needs to be dug out and re-poured, and the operator brand. You get the exact quote in writing before we start, and that number does not change at the door. Call (469) 530-2485 for a free estimate.
We Also Serve Cities Near Garland
Our crews regularly work in Garland neighborhoods like Firewheel, Northlake, and Duck Creek, and we run installations just across the line in Sachse, Rowlett, Wylie, and Richardson. The soil and lot conditions change block by block out here, and our Gate Installation team knows the difference between a Richardson flat lot and a Garland clay ridge. If you’re nearby, the same written price and background-checked crew policy applies.
Serving Garland, TX – Our Local Coverage Area
We’re based in the Garland area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Installation in Garland
Because the panel was never the problem. The hinge post is. Garland sits on Blackland Prairie clay, which swells when wet and shrinks when dry. A post poured at code minimum or bolted to an existing slab moves with that cycle, and the gate sags over the post, not in the middle. We fix the footing, not the panel. Call (469) 530-2485 and we’ll explain what your post is actually doing before we quote anything.
A proper install includes a dedicated power circuit, a reinforced operator mount, travel limits set for gate weight, safety photocells and edge sensors at correct height and aim, and a full two-pass reversal test. Most cheap installs in Garland skip the dedicated circuit and the reversal test. We do not. Quotes are free and the price is written before work starts.
Yes, in most cases. A slide gate needs a level track or a cantilevered design that doesn’t drag on grade. On sloped Garland driveways, we usually build a cantilever slide or raise the track on a concrete curb. It costs more than a flat-lot slide gate, typically adding $1,500 to $3,000, but it will actually operate. Call (469) 530-2485 for a written quote based on your specific grade.
Most single swing gate installations in Garland take two to three working days from the day we start digging to the final reversal test. Fabrication happens off-site first, usually a week or two depending on the build queue. We never promise same-day installation, because a footing poured into Garland clay needs cure time before the gate goes on. We’ll give you a schedule in writing with the quote.
Yes. Solar operators work well in Garland, especially on single gates with low cycle counts in the north and east parts of the city. The panel needs a clear southern exposure, and the battery must be sized for our heat, which shortens battery life. We’ll tell you honestly if your site is a poor solar candidate rather than selling a system that will strand you. Free site evaluation is part of the estimate. Call (469) 530-2485.
Written by Lonnie Burke, Owner at Carver Gate Repair, serving Garland since 2008.