Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Garland, TX
Gate repair in Garland means working on steel and iron that has been through real Texas heat, hard clay soil movement, and more than a few hailstorms. A gate that functioned in April can sag, bind, or stop latching by August when the ground shifts and the metal expands. We handle the full range of gate work in Garland, from a welded hinge replacement to a full motor rework. If you have a gate that will not open or a post that has started to lean, call (469) 530-2485 and you will get a live person, not a voicemail.
Why Garland Homes Are Different
Garland sits on the north and east side of Dallas, and its housing stock runs the full span from 1950s brick ranch homes in older streets like those off Saturn Road and Belt Line, to newer subdivisions further north toward Firewheel and the areas along Naaman Forest. That age spread means we see two very different gate problems. Older Garland properties often have ornamental iron gates set in poured concrete that has cracked from decades of clay soil expansion. Newer properties, particularly those built after 2000, are more likely to have aluminum drive gates with electric operators that were installed by the homebuilder and never truly dialed in.
The soil here is the constant. Garland sits on the Austin Chalk and the black gumbo clay that covers much of Dallas County. That clay swells when it rains and shrinks hard during the long dry stretches from July through September. A gate post set in concrete moves with that soil, and even a quarter inch of movement at the post base translates to a gate that drags on the latch side or a motor that trips its limit switch early. We set posts below the active clay layer and re-pour with a deeper footing, but that baseline matters when a homeowner asks us why the gate worked fine last spring and now will not close.
Our Main Garland Services
Most calls we take in Garland come down to two things: a gate that has stopped working, or a gate that should have been installed better in the first place. Each of these has its own Garland page with full detail.
Gate Repair in Garland
Gate repair in Garland usually starts with either a hinge failure, a bent or sagging frame, or a latch that will not catch. On a welded steel gate, hairline cracks at the hinge are common after a few years of clay-soil movement. On an aluminum drive gate, the problem is often the wheels or the track if it has one. We send a uniformed technician who is background-checked, and before that technician touches anything, you get a written price. The repair itself, once approved, is covered by our written guarantee for a full year. Gate Repair in Garland covers the full scope.
Gate Installation in Garland
A new gate in Garland is not just a slab of metal hung between posts. The right installation accounts for that moving clay soil, the prevailing wind, and the weight of the gate on the operator. We measure, then we build to the measurement, and we give you a written price before any material is ordered. That price covers the gate, the posts, the hardware, and the operator if you want one. There are no surprises on the invoice. Gate Installation in Garland walks through the whole process.
Gate Motor Repair in Garland
Gate motor work in Garland is a specialized job. Swing operators fail when the sun bakes the control board. Slide operators bind when the chain stretches or the wheels flatten. We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems, which covers nearly every motor installed in Garland over the past twenty years. If the board is dead, we replace it. If the limit switch is out of alignment, we correct it. Every motor repair carries the same written one-year guarantee. Gate Motor Repair in Garland has the full breakdown by symptom.
What happens when you call
- 1
A real person answersNo phone trees – you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Garland
Our Garland trucks carry control boards, remotes, photo eyes, and limit switches for the four brands we see most often in this market: FAAC, BFT, Linear, and Viking. That local parts stock means many motor repairs are completed in a single visit rather than waiting on a distributor. See our brands for the full list of what we train on and stock.
Pricing for Gate Company in Garland, TX
| Service | Typical range in Garland |
|---|---|
| Gate hinge replacement (single pair) | $180 – $320 |
| Gate latch or lock repair | $140 – $260 |
| Sagging gate realignment | $220 – $380 |
| Gate post reset (single post) | $320 – $560 |
| Weld repair on ornamental iron gate | $160 – $340 |
| Gate wheel or roller replacement | $120 – $240 |
| Control board replacement | $280 – $540 |
| Limit switch replacement | $160 – $300 |
| Photo eye sensor replacement | $140 – $260 |
| Full gate motor replacement (operator only) | $700 – $1,400 |
| Basic gate installation (single swing, no motor) | $1,500 – $3,200 |
| Driveway slide gate installation with motor | $4,000 – $8,500 |
What moves the price in Garland is usually access and the condition of the existing posts or pad. A gate set on a cracked slab with shifting posts costs more to repair correctly than the same gate on a stable concrete pad. Whatever the number is, you get it in writing before work starts, and that number does not change at the door.
Neighborhoods We Serve in Garland
We cover all of Garland, from the older grid streets near Downtown and the areas around Interstate 30 to the newer neighborhoods up near Firewheel and the subdivisions along Naaman School Road. Response time is typically same-day for motor failures and next-day for larger install work.
- Firewheel
- Club Hill
- Brentwood Place
- North Garland / Naaman Forest area
- South Garland / Duck Creek area
Service Area – Cities Near Garland
Garland sits next to several communities we cover daily. We work in Sachse, TX to the northeast, Rowlett, TX to the east, Wylie, TX further out along Highway 78, and Richardson, TX to the west. Dispatch and scheduling for these areas are coordinated from our Dallas-Fort Worth office, and crews are based locally in Garland.
Serving Garland, TX – Our Local Coverage Area
We’re based in the Garland area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Garland
Most motor failures and stuck-gate calls in Garland are scheduled same-day. We dispatch a technician directly from our Garland crew, not from a call queue. Call (469) 530-2485 and a live person will confirm the arrival window before you hang up.
Some Garland neighborhoods with mandatory HOAs, especially newer subdivisions around Firewheel and north Garland, require written approval before a gate is replaced or a motor is upgraded. We are familiar with the local processes and can provide the technical specs your HOA board will ask for. Call (469) 530-2485 and we will walk you through what your specific neighborhood requires.
We cover every corner of Garland, from the 75040 and 75041 ZIP codes near Downtown and Duck Creek to the 75044 and 75040 areas along Naaman Forest and Firewheel. No service-area surcharge applies within city limits. Call (469) 530-2485 for a free estimate, and you will get a written price before any work begins.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Garland Customers Say
"Gate hinge was bending under the weight. Welded a new bracket on and re-hung it. Solid now."
- Rudy A."Slide gate wasn't opening fully. Veteran tech found a worn drive chain and a misaligned limit. Fixed both in one visit."
- Don H."Good repair on a motor board. Waited a few days on the part, but they stayed in contact."
- Shelby T.