Gate Repair in Ennis - Same-Day Repair, Priced Before We Start

Fast, Reliable Gate Repair Across Ennis

Gate repair in Ennis, TX typically runs $150 – $450 for common fixes like sag correction, hinge work, and operator troubleshooting. Most repairs we handle in Ennis are done in a single visit, with a written price agreed before any work starts. If your gate is dragging the drive, reversing when it shouldn’t, or refusing to open at all, call (469) 530-2485 and a live person answers, day or night. We dispatch background-checked, uniformed technicians to Ennis, and every repair carries our 365-Day Done Right Promise in writing.

Call (469) 530-2485

Why Carver Gate Repair Is Ennis’s Preferred Gate Repair Company

Ennis homeowners deal with a specific kind of gate trouble, and it starts in the ground. The Blackland Prairie clay under this town swells and shrinks with every wet-dry cycle, and that movement works on gate posts and footings like a slow pry bar. A generalist contractor who treats a gate as an afterthought will crank a hinge and call it fixed. We treat the post footing, the panel alignment, and the operator as one system. That approach is why Lonnie Burke and the Carver Gate Repair team get repeat calls from neighborhoods all over Ennis, from the historic homes off West Ennis Avenue to the newer builds near Lake Bardwell.

We coordinate dispatch and scheduling from our Dallas-Fort Worth office, and crews serve Ennis locally. Response time to most of Ennis is under 90 minutes for emergency calls. Every technician who steps onto your property is background-checked and in uniform, so you know exactly who you’re letting through the gate. Our reviews from Ennis customers consistently mention two things: the price didn’t move, and the gate stayed fixed. That’s The Garrison Standard, and we’ve operated under it since 2008.

Wrought Iron Gate Repair in Ennis

Wrought iron gate repair in Ennis is our most common call, because iron gates are heavy and Ennis clay doesn’t hold still. When the soil heaves, a wrought iron gate sags at the hinge post, not the middle. The panel itself is usually fine; it’s the footing underneath that’s gone out of plumb. Fixing it properly means addressing the post first, then re-leveling the panel, then testing the operator. In Ennis, expect to pay $180 – $380 for sag correction and hinge work on a standard single swing gate, and $400 – $900 if the post footing needs to be pulled and re-set.

Post Footing and Hinge Repair

Out on a wrought iron swing gate off West Ennis Avenue, the gate had dropped and was catching the drive. Our tech found the hinge post itself had heaved in the clay, so we pulled and re-set the post footing rather than just cranking the hinges. The sag correction started at the post. We then re-leveled the panel and tested the LiftMaster operator’s safety photocell and reversal, and it’s been swinging clean since.

That’s the difference between a repair that lasts and one that puts you back on the phone in six weeks. We don’t shim a post that needs to be set. We dig it out, re-set the footing, and let the concrete cure before re-hanging the panel.

Weld and Rust Repair

Wrought iron rusts, and Ennis humidity doesn’t help. Surface rust is cosmetic and can be wire-brushed and sealed. Rust that has eaten through a weld or a bottom rail is structural, and that calls for grinding out the old weld and laying a new one. Weld and rust repair on an Ennis wrought iron gate generally runs $120 – $300 per affected section, depending on how far the corrosion has gone.

Metal Gate Repair in Ennis

Metal gate repair in Ennis covers steel tube gates, aluminum drive gates, and the mixed-metal setups you see on ranchette properties south of town along I-45 and out toward Bardwell. These gates fail differently than wrought iron. Aluminum gates bend before they break; steel tube gates crack at the weld joints where the frame meets the infill. When a metal gate binds or drags in Ennis, the usual suspects are a post that’s racked in the clay, a hinge that’s worn oval, or a latch that was never shimmed to begin with. Typical metal gate repair in Ennis runs $150 – $400.

Gate Realignment

A metal gate that doesn’t close square is usually a post problem wearing a panel problem. We check the post with a level before we touch the hinges. If the post is plumb, we re-shim the hinges and adjust the latch strike. If it isn’t, we re-set the post first. Realignment alone generally runs $140 – $280 on most Ennis residential gates.

Hinge and Post Repair

Hinges wear out. A steel pin in a steel barrel, swinging a 300-pound gate panel thousands of times a year, will eventually go oval. When that happens, the gate drops and starts scraping. Replacing worn hinges and re-shimming the panel typically runs $150 – $300. If the post itself is moving, add $300 – $600 for a footing re-set, which is common in Ennis’s shrink-swell clay.

Trusted Brands We Service in Ennis

Our technicians are trained on nine gate-motor brands, including Viking, Ghost Controls, DoorKing, and Elite. That matters when your operator is five years old, discontinued, and the manufacturer’s phone line puts you on hold for an hour. We keep common parts stocked for Ennis jobs, so a bad limit switch or a failed loop detector doesn’t mean waiting a week for a freight shipment. If your system is already installed and wired, Gate Repair on the operator itself is often a same-visit fix. If the motor is beyond saving, we quote a replacement with the same written-price rule: you see the number before we touch the job.

Common Gate Repair Problems We See in Ennis Homes

• Hinge-post sag from expansive clay. Ennis sits on Blackland Prairie soil that swells when wet and shrinks when dry. That cycle racks gate posts out of plumb, and the gate sags at the hinge post, not the middle.
• Slide gate binding after the pad settles. Slide gates ride on a concrete pad, and when that pad settles off-level from soil movement, the rack and pinion bind. The motor strains, the gate shudders, and eventually something breaks.
• Operator faulting from misaligned safety sensors. A photocell that’s drifted out of alignment or an edge sensor that was never wired to UL 325 entrapment-protection standards will cause an operator to reverse or refuse to close. It’s a safety feature doing its job, but it needs correcting.
• Latch and lock failure at the drop rod. The drop rod that holds a double gate closed is the first thing to seize when the gate shifts. If one leaf moves even half an inch, the rod won’t seat, and the gate won’t lock.

Pricing for Gate Repair in Ennis, TX

We Also Serve Cities Near Ennis

Our crews work throughout Ellis County and the southern metro. If you’re in Waxahachie, Red Oak, Wilmer, or Lancaster, we handle Gate Repair in Ennis and the surrounding area with the same Garrison Standard: written prices, background-checked technicians, and a full-year guarantee on every repair.

FAQs About Gate Repair in Ennis