Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Fresno
Gate repair in Fresno usually falls into two camps: a gate that sags and drags because the post has shifted in our clay soil, or an operator that quit because heat, ground movement, or a failed component finally wore it down. Most repairs in Fresno run between $150 and $900 depending on whether we’re re-setting a post, replacing a limit switch, or installing a new motor. Call (469) 530-2485 and a live person answers, 24/7. We serve the whole Fresno area with background-checked, uniformed technicians and a written price before any work starts.
Why Carver Gate Repair Is Fresno’s Preferred Gate Repair Company
Fresno homeowners deal with gate problems that generalist handymen don’t see often enough to fix correctly. Our Gate Repair team works exclusively on gates and openers, which matters when the issue is a post that’s shifted in expansive clay or an operator that’s been misaligned for months. We answer the phone around the clock, dispatch a uniformed tech, and hand you a written price before any work begins. That’s The Garrison Standard, and it’s how Carver Gate Repair has operated since 2008.
Every repair carries a 365-Day Done Right Promise. If our work fails within a year, we return and make it right at no charge. The guarantee is in writing on every invoice. Fresno residents call us because the number works, the tech shows up, and the price doesn’t move at the door.
Fresno sits on Fort Bend County clay. It expands when wet and contracts when dry. That movement is the single biggest reason gates in this area sag, bind, and strain their operators. A general repair crew might tighten a hinge and call it done. We check the post footing, the gate geometry, and the operator’s alignment, because if the post is moving, the hinge was never the problem.
Wrought Iron Gate Repair in Fresno
Wrought iron gate repair in Fresno typically means correcting sag, re-anchoring hinge posts, and repairing cracked welds at stress points along the frame. Fresno’s expansive soil puts constant pressure on footings, and iron gates are rigid, so the movement shows up as a gate that drags, latches that no longer line up, or welds that crack near hinges. A typical wrought iron gate repair in Fresno runs $250 to $1,100 depending on whether we’re re-welding, re-setting a post, or re-aligning the entire gate leaf.
Hinge and Post Corrections
When a wrought iron gate sags, the hinge post is often the actual failure. In Fresno, we regularly excavate the post footing, find that clay heave or settlement has moved the post, and re-pour the concrete to correct the geometry. Adjusting hinges without fixing the post is a temporary fix. We do the footing work so the repair holds.
Welding and Rust Repair
Iron gates in Fresno’s humidity and occasional flooding conditions develop rust at the lower corners and hinge plates. We grind back the corrosion, re-weld the original or replacement steel, and prime the repaired area. If the damage is structural, we replace the section rather than layering weld over failing metal. That’s the only way a repair lasts under repeated gate cycling.
Metal Gate Repair in Fresno
Metal gate repair in Fresno covers steel and aluminum gates, both swing and slide designs. The work usually involves straightening bent rails, replacing damaged pickets, repairing failed welds, and re-aligning the gate on its track or hinges. Fresno’s soil movement and storm-driven debris both contribute to bent bottom rails and dragging gates, and repair costs here generally fall between $200 and $950 for most metal gate repairs.
Slide Gate Track and Roller Repairs
Slide gates in Fresno develop problems when the v-track shifts or the rollers wear flat. If the concrete track has settled, the gate will bind or jump the rail. We repair or re-set the track, replace worn rollers, and test the full travel before we leave. A proper slide gate repair includes verifying the gate stops and receiver post are still square.
Realigning Twisted or Racked Gates
Storm winds and soil movement can twist a metal gate frame enough that the latch no longer engages or the gate scrapes the ground. We assess the frame’s square, correct the racking, and add bracing where needed. On older gates, we’ll often recommend replacing hinge hardware at the same time, because that’s where the next failure will show up.
Trusted Brands We Service in Fresno
Our technicians carry parts and diagnostic equipment for Linear, Viking, Ghost Controls, and DoorKing operators, along with LiftMaster, FAAC, BFT, Elite, and Mighty Mule equipment. Fresno homeowners don’t have time to wait for a part to ship from a distributor. We keep common control boards, limit switches, remote receivers, and safety sensors on the truck so most operator repairs are completed in one visit. When a part needs to be ordered, we tell you the timeline and the price before you approve anything.
Common Gate Repair Problems We See in Fresno Homes
- Hinge post settlement. Fresno’s expansive clay shifts with moisture, and the post moves just enough that the gate drags or the latch misses. Re-setting the post in a deeper, properly cured footing is the only fix that lasts.
- Solar gate opener batteries failing early. Fresno summers routinely exceed 100 degrees, and heat shortens lead-acid and lithium battery life inside solar operators. We test the charge controller and replace batteries with heat-tolerant options when needed.
- Loop detector failure. Buried inductance loops shift or break when the ground moves, and the operator stops sensing vehicles. The symptom is a gate that opens by remote but not when a car pulls up. We locate the break, replace the loop, and retune the detector.
- Operator gear wear from misaligned gates. When a gate drags or binds, the operator’s rack and pinion or drive gear wears unevenly. Repairing the gate alignment without replacing the damaged gear only postpones the next failure.
Pricing for Gate Repair in Fresno, TX
Repair pricing in Fresno is straightforward but it does depend on what actually failed. Here are the ranges we see most often:
- Wrought iron gate repair: $250 – $1,100
- Metal gate repair: $200 – $950
- Gate motor replacement: $600 – $1,600
- Limit switch or control board replacement: $180 – $450
- Post re-setting with new concrete: $400 – $1,200
- Solar opener battery and charge controller service: $150 – $400
The final price depends on gate size, material, and what parts your system needs. What doesn’t change: we give you a written price before any work starts, and the number doesn’t move unless you approve an additional repair. Estimates are free. Call (469) 530-2485 to schedule a technician.
We Also Serve Cities Near Fresno
Our Gate Repair in Fresno crew also covers Missouri City, Manvel, Stafford, and Sugar Land. If you’re just outside Fresno city limits, we can usually reach you the same day for an emergency and within scheduled windows for standard repairs. Call us and we’ll confirm current availability in your area.
Serving Fresno, TX – Our Local Coverage Area
We’re based in the Fresno area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Fresno
Because the hinge post is moving, not the hinge hardware. Fresno’s clay soil expands and contracts with moisture, and over time the post footing shifts. Tightening hinges won’t fix a moving post. We re-pour the footing, re-set the post, and then correct the gate alignment. Call (469) 530-2485 and we’ll inspect the post before quoting the repair.
Every 30 days, and more often during Fresno’s storm season when wind-blown debris and moisture can knock sensors out of alignment. A misaligned photocell means the gate may not reverse when a person or vehicle is in its path. During any repair, we test and certify photocell operation before leaving. Call (469) 530-2485 to schedule a safety check.
Yes. Fresno’s summer heat shortens battery life in solar openers, and the charge controllers often fail before the panel or motor does. We test the full system: panel output, controller function, and battery condition. We stock replacement batteries and controllers for Linear, Viking, Ghost Controls, and DoorKing solar units. Call (469) 530-2485 for a diagnostic.
We start by checking power to the keypad and the receiver. In Fresno, heat and humidity corrode wiring connections at the keypad and at the control board. Then we test the keypad’s output, the receiver’s response, and the operator’s limit switch function. Most keypad failures are fixed in under an hour. Call (469) 530-2485 and we’ll come out and diagnose it.
Most repairs are completed in one to three hours. Post re-setting and concrete work can take longer if we need to let the footing cure before re-hanging the gate. We’ll give you a time estimate with your written price, and we stick to it. Call (469) 530-2485 to schedule.
In the Sunnyside neighborhood, we repaired a sagging wrought iron swing gate on a LiftMaster operator. The hinge post had settled, causing the gate to drag and the operator to strain. We excavated and re-poured the post footing, then performed sag correction and adjusted the rack and pinion. The gate now cycles smoothly and the safety photocell was tested and certified.
Written by Lonnie Burke, Owner at Carver Gate Repair, serving Fresno with The Garrison Standard since 2008.