Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Cibolo, TX
Gate work in Cibolo, TX follows a clear pattern: homes sit on larger lots than you’d find closer to San Antonio, many gates are the original builders’ models from the early 2000s, and the clay soil that runs through this part of Guadalupe County shifts with every wet-dry cycle. That soil movement is the quiet culprit behind a lot of what we’re called out for here. Posts lean, gates drag, and motors work against a frame that’s no longer square. Carver Gate Repair handles all of it, from a dragging gate in Turning Stone to a dead operator in Falcon Ridge. Call (469) 530-2485 and a real person picks up, day or night.
Why Cibolo Homes Are Different
Cibolo’s housing stock grew fast between about 2000 and 2015, which means a large share of the gates we see are original equipment. A gate installed when the house was built is now 15 to 25 years old. Hinges have worn, operator arms have been through hundreds of open-close cycles a week, and the posts that looked plumb at installation have settled unevenly. The soil here expands when wet and contracts when dry, and that cycle works on a gate post over years until the gate no longer seats in the catch.
Neighborhoods like Turning Stone, The Heights of Cibolo, Falcon Ridge, and Red River Ranch were built with different gate packages depending on the builder, so there’s no single “Cibolo standard” when it comes to what breaks first. What holds true across all of them: the weather does the damage slowly, and by the time a homeowner notices, the fix involves more than a hinge adjustment. A gate that drags today was probably binding for six months before the wheel gave out.
HOA communities are common here, and several require gates to be maintained to a certain appearance standard. If your community has a property management firm, it’s worth checking the CC&Rs before changing a gate or its operator. We work within those requirements regularly and can advise on what typically passes architectural review in Cibolo’s managed neighborhoods.
Our Main Cibolo Services
The three calls we get most from Cibolo homeowners are gate repair, gate installation, and gate motor repair. Each has its own page with local pricing and what the job involves, but in short: repair keeps your existing gate working, installation replaces the whole system when repair no longer makes sense, and motor repair restores an operator that’s quit without forcing you into a full replacement.
Gate Repair in Cibolo
A gate that sags, drags, or won’t latch is the most common call in Cibolo, and it’s usually a hinge, wheel, weld, or post problem before it’s a motor problem. We square the gate to the post, replace worn hinges and wheels, reweld split joints, and leave the gate swinging true. In Cibolo’s clay soil, post lean is a frequent root cause, so we check the post’s plumb before adjusting anything else. Learn more on our Gate Repair in Cibolo page.
Gate Installation in Cibolo
When the posts are too far gone, the gate frame is cracked through, or the yard has been reworked and the old gate no longer fits the opening, replacement is the honest call. We build swing and slide gates sized to your entrance, set posts below the frost line, and match operators that fit the gate’s weight and cycle count. For Cibolo homes with HOA review, we can walk through what documentation your association typically asks for. See the Gate Installation in Cibolo page for a full breakdown.
Gate Motor Repair in Cibolo
Operators fail in specific ways: a limit switch that no longer stops the gate at the right point, a loop detector that fails to sense a car, a control board that’s taken a power surge. Cibolo sees plenty of surges during spring thunderstorms. We diagnose the exact component that’s failed and replace it, rather than quoting a whole new operator when only a $60 part is bad. Details on the Gate Motor Repair in Cibolo page.
What happens when you call
- 1
A real person answersNo phone trees – you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Cibolo
Most Cibolo neighborhoods have a mix of LiftMaster, FAAC, BFT, and Linear operators, with occasional Viking and DoorKing units on larger or custom entrances. We carry common parts for all nine brands we service in our trucks, which keeps most Cibolo repairs to a single visit. See our brands for the full list and what each one typically needs.
Pricing for Gate Company in Cibolo, TX
| Service | Typical range in Cibolo |
|---|---|
| Gate repair, minor (hinge adjustment, wheel replacement) | $120 – $300 |
| Gate repair, moderate (weld, post re-set, sag correction) | $300 – $700 |
| Gate repair, major (frame replacement section, rebuild) | $700 – $1,500 |
| Gate motor repair (limit switch, capacitor, loop detector) | $150 – $400 |
| Gate motor replacement (operator unit) | $600 – $1,600 |
| Slide gate operator replacement | $900 – $2,400 |
| Swing gate operator replacement (single arm) | $700 – $1,800 |
| Full gate installation (standard swing gate, single) | $1,800 – $4,000 |
| Full gate installation (slide gate, heavier frame) | $3,000 – $7,000 |
| Service call / diagnostic | $75 – $150 |
Prices in Cibolo run toward the middle of these ranges: soil movement means more post re-sets than other metros, but the housing stock is new enough that most gate frames are still sound. Every job gets a written price before we start, and that number doesn’t move at the door.
Neighborhoods We Serve in Cibolo
We work across Cibolo regularly, from the older streets near Main to the newer builds on the northeast side. Same-day response is typical for repair calls; installation and full motor replacements are scheduled after a free measure.
- Turning Stone
- Falcon Ridge
- The Heights of Cibolo
- Red River Ranch
- Oaks of Cibolo
Service Area – Cities Near Cibolo
We serve Cibolo and the surrounding communities from our San Antonio dispatch office. If you’re a few minutes down the road, we’re there regularly. Our nearby service area includes Schertz, TX, Universal City, TX, Converse, TX, and New Braunfels, TX.
Serving Cibolo, TX – Our Local Coverage Area
We’re based in the Cibolo area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Cibolo
Repair calls in Cibolo are typically same-day when you reach us before 3 p.m. Weekends and holidays are covered too. The phone is answered by a person, not a queue, twenty-four hours a day. Call (469) 530-2485 and we’ll give you a real arrival window.
It depends on your community’s CC&Rs. Repairs that restore the gate to its original condition usually don’t require review. A replacement gate or a different operator often does. We can tell you what your HOA typically asks for and provide spec sheets for review packets.
Our Cibolo service area includes Schertz, Universal City, Converse, and New Braunfels among the surrounding communities. Dispatch runs from the San Antonio office, but crews work in Cibolo daily. If you’re on the edge of the city limits, call and we’ll confirm a window.
If your gate is acting up, call Carver Gate Repair at (469) 530-2485. We’ll give you a straight answer and a written price before any work starts.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Cibolo Customers Say
"Keypad and remotes set up fresh for the whole neighborhood. Done cleanly and quickly."
- Chris W."Straight answers on whether to repair or replace the operator. Repair was the right call."
- Wanda F."Gate hinge was bending under the weight. Welded a new bracket on and re-hung it. Solid now."
- Rudy A.