Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Temple City, CA
Carver Gate Repair handles gate repair, gate installation, and gate motor repair across Temple City, California. Most Temple City homes run a wrought iron or steel driveway gate on a swing or slide track, and the climate here means dry summers, occasional winter rain, and soil that shifts enough to knock a gate out of square. That combination keeps our crews busy year-round. If your gate is dragging, binding, or refusing to open, call us at (469) 530-2485 and a real person will answer, day or night.
Why Temple City Homes Are Different
Temple City is a grid of mostly single-family homes built between the 1940s and the 1980s, many with original gate posts set in clay-heavy soil. That matters because the soil expands and contracts through wet winters and dry summers, and over decades the posts drift. A gate that closed fine in January can start dragging by July. When we work in Temple City, we check the plumb of the posts before we touch the hinges, because adjusting an operator on a leaning post only buys a few months.
The other difference is the lot pattern. Many Temple City driveways are short by Los Angeles standards, which means gates sit close to the house and close to the street. A slide gate that might have room to run in Arcadia often does not in a Temple City side-yard layout. That pushes more homeowners toward swing gates and articulating-arm operators, which change the parts we stock and the way we set the limit switches. None of this is exotic to us; it is just the specific set of conditions that shows up on Temple City jobs.
Our Main Temple City Services
Three services cover nearly every call we take from Temple City homeowners: repair, installation, and motor repair. Each one has its own Temple City page with full pricing and details.
Gate Repair in Temple City
Gate repair in Temple City usually means a gate that will not swing or slide cleanly, a wheel assembly that has worn out, a hinge that has sagged, or a track that has filled with silt after a winter rain. We square the leaf, replace the worn hardware, and set the gate back on its track so it moves without dragging. Most Temple City repairs are completed the same day we are on site. Lonnie Burke and the crew will give you the written price before any work starts. Full details are on our Gate Repair in Temple City page.
Gate Installation in Temple City
A new gate in Temple City starts with a measured look at the driveway layout, the post conditions, and how far the gate needs to clear the house line. We install steel and wrought iron driveway gates built to the opening, with hinge posts set correctly for the soil, not for a generic diagram. Installation is scheduled work with a written price and a fixed schedule, not a same-day job. See Gate Installation in Temple City for the full scope and what to expect.
Gate Motor Repair in Temple City
When the opener runs but the gate does not move, or the gate reverses on its own, the problem is usually in the motor, the limit switch, the gearbox, or the loop detector under the driveway. We service the motor systems most common in Temple City drives, including Viking, Ghost Controls, and DoorKing. Our technicians carry the boards and gear sets for those brands so the repair does not wait on a parts order from out of state. The full diagnostic process is on our Gate Motor Repair in Temple City page.
What happens when you call
- 1
A real person answersNo phone trees – you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Temple City
Carver Gate Repair works on nine gate-motor brands, including Viking, Ghost Controls, DoorKing, and Elite systems commonly installed in Temple City. Having brand-specific parts on the truck is the difference between a same-week repair and a two-week wait. Our technicians are trained across the full line; see our brands for the complete list.
Pricing for Gate Company in Temple City, CA
| Service | Typical range in Temple City |
|---|---|
| Gate repair (general hardware, wheel, hinge) | $175 – $525 |
| Gate motor repair | $225 – $550 |
| Gate operator replacement | $550 – $1,600 |
| Gate installation (new build) | $1,900 – $8,500 |
| Slide gate wheel assembly replacement | $225 – $475 |
| Swing gate hinge replacement | $275 – $500 |
| Limit switch replacement | $150 – $350 |
| Loop detector replacement | $160 – $380 |
| Gate opener remote / receiver replacement | $100 – $250 |
What pushes a Temple City price up is usually the condition of the posts and the age of the opener. A gate that has been scraping its post for two years has done hidden wear to the hinge blocks and wheel brackets, and that shows up in the quote. The price we put in writing before work starts is the price you pay, and every repair carries a written guarantee for a full year.
Neighborhoods We Serve in Temple City
We cover all of Temple City, from the streets near Rosemead Boulevard to the neighborhoods east of Temple City Boulevard and up toward the northern edge near Arcadia. Same-day repairs are generally available across the entire Temple City area.
- North Temple City
- Central Temple City
- South Temple City
- West Temple City / near Rosemead Blvd
- East Temple City / near Temple City Blvd
Service Area – Cities Near Temple City
In addition to Temple City, our crews work the neighboring cities across the San Gabriel Valley. If you are just outside Temple City, we also serve El Monte, CA, San Gabriel, CA, Arcadia, CA, and Rosemead, CA. If you are not sure which page applies to your address, call us and the dispatcher will point you to the right one.
Serving Temple City, CA – Our Local Coverage Area
We’re based in the Temple City area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Temple City
Most Temple City addresses are reached the same day you call, often within a few hours. Dispatch and scheduling run out of the brand’s Los Angeles office, and crews stage locally in the San Gabriel Valley so they are not driving across the county to reach you. Call (469) 530-2485 and we will give you a real arrival window.
Some Temple City properties fall under HOA covenants that specify gate height, material, or color, and we see that most often in the central and northern neighborhoods. A call to your HOA office before a new gate installation settles it in ten minutes. Most repairs and motor replacements do not require a city permit.
Yes. Gate installations and full operator replacements are booked on a scheduled basis with a written price and a firm appointment window. Repairs that involve a gate stuck open or a failed motor are prioritized and usually handled the same day. Call (469) 530-2485 for a free estimate on any Temple City gate job, and you will get the price in writing before any work begins.
For gate repair, installation, or motor repair in Temple City, call Carver Gate Repair at (469) 530-2485. A live person answers, the price is written before work starts, and every repair is guaranteed in writing for a full year.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Temple City Customers Say
"Keypad and remotes set up fresh for the whole neighborhood. Done cleanly and quickly."
- Chris W."Straight answers on whether to repair or replace the operator. Repair was the right call."
- Wanda F."Gate hinge was bending under the weight. Welded a new bracket on and re-hung it. Solid now."
- Rudy A.