Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Broadview Park, FL
Carver Gate Repair is the gate company Broadview Park homeowners call when a swing gate stops opening or a slide gate jumps its track. Most of the work we do in this part of Broward County comes down to three things: salt air that corrodes motors faster than inland towns, older gate systems installed when homes were built in the 1970s and 1980s, and driveways that hold boats, work trailers, and extra cars. We work on nine gate-motor brands, carry the common wear parts on the truck, and every job starts with a written price before any work begins. Call (469) 530-2485 and a live person answers, day or night.
Why Broadview Park Homes Are Different
Gate work in Broadview Park is shaped by where the town sits: a few miles from the Atlantic, with humidity that never really lets up. Swing gate hinges and slide gate rollers here rust on a different schedule than they do ten miles west near the Everglades. Control boards exposed to that salt air tend to fail at the terminal connections first, which is why we check and clean those points on every motor repair rather than just replacing parts and leaving.
The housing stock matters too. Broadview Park has a heavy concentration of single-family homes built before 1990, many on oversized lots along streets like SW 22nd Avenue and SW 24th Street. Driveways are wide enough for boats and work trucks, and the gates themselves are often custom steel or aluminum, built to match the house. Those older gates are repairable, but they need a technician who knows how the original hardware was installed, not someone who shows up expecting an off-the-shelf opener. The terrain is flat, which means drainage matters: a gate post set into low ground will shift during summer storms if the base was never properly poured. We see that in Broadview Park more than anywhere else in the county.
Our Main Broadview Park Services
Most calls from Broadview Park fall into three categories: a gate that stopped moving, a gate that needs to be replaced, or a motor that runs but won’t do its job. Each service has its own page with specifics, pricing, and what to expect on the day of the work.
Gate Repair in Broadview Park
A gate repair in Broadview Park usually starts with the same question: is the gate itself damaged, or is the motor failing to operate it? We diagnose the difference before quoting anything. Common work here includes re-welding broken hinge plates, straightening sagging gate leaves, replacing rusted rollers on slide gates, and repairing damaged posts after a storm. The salt air around Broadview Park doesn’t just affect motors – it works on steel frames and weld points too. We give you a written price before any repair starts, and every repair carries our 365-Day Done Right Promise in writing. Details are on our Gate Repair in Broadview Park page.
Gate Installation in Broadview Park
New gate installation in Broadview Park means more than setting posts and hanging a panel. We measure the driveway width, check the ground for drainage, select hardware rated for coastal humidity, and plan the post footings for flat terrain that gets heavy summer rain. Homeowners here typically choose steel or aluminum swing gates, with solar or direct-power operators depending on where the house’s electrical service sits. Every installation includes a written quote before we order materials, and you’ll know the full price before any hole is dug. See Gate Installation in Broadview Park for the full breakdown.
Gate Motor Repair in Broadview Park
Gate motor repair in Broadview Park is the call we get most often from this area. The humidity and salt air shorten the life of limit switches, loop detectors, and control board connections. We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems, and we stock the most-used parts so we’re not waiting on a distributor for a basic fix. If the motor can be repaired, we quote the repair. If it needs replacement, you get that price in writing too. Full details are on the Gate Motor Repair in Broadview Park page.
What happens when you call
- 1
A real person answersNo phone trees – you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Broadview Park
We service and stock parts for the gate motors Broadview Park homes actually have installed: Viking, DoorKing, and Elite are the three we see most on swing gates, with Ghost Controls common on lighter residential setups. The right parts and wiring knowledge are matched to the system already on your property, which keeps turnaround tight. See our brands for the full list.
Pricing for Gate Company in Broadview Park, FL
These are the price ranges homeowners in Broadview Park can expect for common gate work, based on what we typically see in this market. Every quote is written and fixed before work begins.
| Service | Typical range in Broadview Park |
|---|---|
| Gate repair, minor (hinge adjustment, roller replacement, latch) | $95 – $250 |
| Gate repair, moderate (weld repair, post reset, track alignment) | $250 – $550 |
| Gate repair, major (full hinge replacement, frame straightening) | $550 – $1,200 |
| Gate motor repair (limit switch, capacitor, wiring) | $150 – $350 |
| Gate motor replacement (swing operator) | $850 – $1,800 |
| Gate motor replacement (slide operator) | $1,200 – $2,500 |
| Control board replacement (brand-dependent) | $250 – $650 |
| Loop detector installation or replacement | $300 – $700 |
| New gate installation (single swing, standard steel/aluminum) | $2,500 – $6,000 |
| New gate installation (custom, long driveway, dual swing) | $4,000 – $9,500 |
| Full system install (gate + motor + safety edges + sensors) | $3,800 – $8,000 |
What pushes price up in Broadview Park is usually corrosion repair on older steel frames and the extra labor of re-setting posts that shifted in saturated ground. Salt air damage means a repair that looks simple on the surface is sometimes a weld-and-reinforce job underneath, and that’s priced plainly, before any work starts.
Neighborhoods We Serve in Broadview Park
We cover all of Broadview Park and the surrounding communities. These are the areas we’re in most often:
- Broadview Park proper, including streets off SR 7 and SW 24th Street
- The residential blocks along SW 22nd Avenue
- Communities near the intersection of Davie Road and Stirling Road
- Homes near Perkins Park and the surrounding grid
- Areas north toward I-595 along the SR 7 corridor
Typical response time for a Broadview Park call is same-day for gate repair and motor repair emergencies when you call before early afternoon. Installations and new gate quotes are scheduled for a free measure, usually within a few business days.
Service Area – Cities Near Broadview Park
While this page covers Broadview Park specifically, we run crews throughout South Florida and beyond. If you’re looking for gate work in other parts of the state, these city pages cover our broader service area: Miami, FL, Tampa, FL, Orlando, FL, and Jacksonville, FL.
Serving Broadview Park, FL – Our Local Coverage Area
We’re based in the Broadview Park area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Broadview Park
For most gate repair and gate motor repair calls in Broadview Park, we can have a technician on site the same day if you call before early afternoon. Dispatch and scheduling are coordinated from our Miami office, with crews serving Broadview Park locally. Call (469) 530-2485 to check current availability.
Most gate replacements in Broadview Park don’t require a permit when the work stays on private property and doesn’t alter existing electrical service. If the job involves new electrical runs or the gate sits on a community-controlled entrance, we’ll flag that before quoting. We handle the scoping on our end so you’re not left guessing.
Yes. We cover the full Broadview Park service area, including homes along SR 7, SW 22nd Avenue, and the residential streets off Davie Road and Stirling Road. Every job starts with a written quote, and the price does not change when the technician arrives.
If your gate stopped working or a motor is making noise it shouldn’t, call (469) 530-2485. A live person answers, and we’ll get you a written quote and a straight answer on timing. The Garrison Standard applies to every Broadview Park job: background-checked technicians, upfront pricing, and a 365-Day Done Right Promise in writing.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Broadview Park Customers Say
"Keypad and remotes set up fresh for the whole neighborhood. Done cleanly and quickly."
- Chris W."Straight answers on whether to repair or replace the operator. Repair was the right call."
- Wanda F."Gate hinge was bending under the weight. Welded a new bracket on and re-hung it. Solid now."
- Rudy A.