Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Broadview Park
Gate installation in Broadview Park typically runs $2,800 – $7,500 for a standard residential driveway gate with automation, and most projects are measured and installed within two to three weeks of your call. We’re Carver Gate Repair, and our crews work Broadview Park regularly, dispatching from our South Florida coordination office to homes off Peters Road, along the Middle River canal, and throughout the 33317 ZIP. If you’re tired of contractors who quote one number and hand you another, call (469) 530-2485. We give you a written price before any work starts, and that number doesn’t move.
Broadview Park sits in Broward County with a mix of mid-century ranch homes, newer infill construction, and waterfront properties along the river. That variety means gate needs here aren’t one-size-fits-all. A swing gate on a 60-foot lot near Southwest 31st Avenue needs different clearances than a sliding gate on a canal-front property with limited setback. We’ve installed both, and we know the local soil conditions, the Broward County wind-load requirements, and how the seasonal afternoon thunderstorms affect operator housing and drainage. Our Gate Installation team measures every site in person, no exceptions.
Why Carver Gate Repair Is Broadview Park’s Preferred Gate Installation Company
We’ve built our reputation in Broadview Park on showing up when we say we will and leaving the site cleaner than we found it. That sounds basic until you’ve dealt with a no-show contractor who finally arrives three hours late and tracks mud through your carport.
Our technicians are background-checked and uniformed on every call. You know exactly who’s walking onto your property, and they know exactly what The Garrison Standard requires: written prices, clean sites, and a full-year guarantee on every repair. The 365-Day Done Right Promise isn’t a sales pitch. It’s in writing on every job.
Phones are answered by a live person 24 hours a day, including weekends and holidays. No voicemail boxes, no “leave a message and we’ll call back Monday.” When you call (469) 530-2485, someone picks up.
We also handle Gate Repair in Broadview Park and Gate Motor Repair in Broadview Park, so if you’re replacing an older system or adding automation to an existing gate, we can assess the full picture rather than selling you a gate and walking away.
Gate Fabrication in Broadview Park
Gate Fabrication in Broadview Park covers everything from custom aluminum driveway gates for homes along the Middle River to wrought-iron pedestrian gates for properties near Peters Road. When a stock gate won’t fit your opening, your slope, or your aesthetic, we measure, cut, weld, and finish on spec. A typical custom fabricated gate in Broadview Park runs $3,200 – $8,500 depending on material, width, and ornamentation.
Aluminum and Steel Options
Aluminum resists the salt air that drifts inland from Fort Lauderdale Beach and doesn’t require the maintenance schedule of steel. For homeowners who want the wrought-iron look without the rust cycle, we fabricate aluminum gates with powder-coated finishes that hold up through Broadview Park’s wet season. Steel costs less upfront and handles impact better, but it needs periodic attention if you live within a few miles of the coast.
Custom Sizing for Tight Lots
Many Broadview Park homes were built on 50- to 75-foot lots in the 1950s and 1960s. That leaves narrow driveways and limited swing radius for a standard gate. We fabricate to the inch, not to a catalog page, so your gate actually opens without clipping your neighbor’s fence or your own landscaping.
Automatic Gate Installation in Broadview Park
Automatic Gate Installation in Broadview Park adds motor-driven openers to new or existing gates, complete with safety edges, loop detectors, and remote or keypad access. A full automatic system on a new gate typically costs $4,500 – $9,500 in this market, with swing operators on the lower end and heavy-duty sliding systems for commercial-grade security on the higher end.
Operator Selection and Placement
The operator is the heart of the system. We match the motor to your gate’s weight, length, and daily cycle count, not to what’s in the warehouse. For the homes near the river with longer driveways, we often spec Linear or Viking sliding operators with battery backup, since power fluctuations during summer storms are common in this part of Broward County.
Safety and Access Controls
Every automatic installation includes photoelectric eyes, safety edges, and a manual release mechanism. We also install loop detectors for vehicle sensing and can add telephone entry systems or smart-home integration if you want to buzz in a delivery from your phone. The Garrison Code requires we test every safety feature in front of you before we sign off.
Trusted Brands We Service in Broadview Park
We stock parts and train our technicians on nine gate-motor brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. For Broadview Park homeowners, that means faster turnaround when something needs replacement. We don’t order a part from California and make you wait two weeks. Our South Florida warehouse carries FAAC and BFT operator components, Linear control boards, and Viking gear kits specifically, so most repairs that follow an installation happen same-day or next-day. If you’re replacing an older FAAC 740 or upgrading from a manual gate to a Linear swing operator, we have the hardware and the know-how matched to what’s already on your property.
Common Gate Installation Problems We See in Broadview Park Homes
- Corrosion from salt-laden afternoon storms. Broadview Park’s location between I-95 and the coast means sea breeze pushes inland most afternoons, especially in summer. We see premature rust on hinges and lower gate frames where drainage is poor, and we spec marine-grade hardware and proper concrete footings with weep holes to move water away.
- Soft, sandy soil that shifts gate posts. The ground in this part of Broward is often loose sand over limestone. A gate post set without proper depth and reinforcement tilts within a year. We pour concrete piers to 36 inches minimum and use post brackets rated for the gate load, not the fence load.
- Inadequate clearance for swing gates on corner lots. Homes near the intersection of Southwest 31st Avenue and Peters Road often have sidewalks and utility strips that eat into the swing arc. We measure the full radius in both directions and recommend sliding or bi-folding configurations when a standard swing won’t work.
- Older homes with no power run to the gate line. Many Broadview Park properties built before 1980 never anticipated automation. We handle the trenching, conduit, and 110V or low-voltage run as part of the installation, pulling permits through Broward County and coordinating with FPL when the meter needs relocation.
Pricing for Gate Installation in Broadview Park, FL
A standard single swing driveway gate with basic automation in Broadview Park runs $2,800 – $4,200. Double swing gates for wider openings typically land at $3,800 – $5,500. Sliding gates, which need track, rollers, and a heavier operator, range from $4,500 – $7,500. Custom fabrication with ornamental ironwork or specialty aluminum can push to $6,500 – $9,500 depending on complexity.
Pedestrian gates without automation start around $1,800 – $2,800 installed. Security gates with access control, intercoms, or telephone entry add $800 – $2,500 to any of the above.
What moves the number: material choice, gate width, automation level, electrical run distance, and whether we need to remove an existing gate and posts. We don’t guess. We measure your site, discuss options, and hand you a written price before any work starts. That price includes materials, labor, permits, and haul-away. No line items appear later. Estimates are free. Call (469) 530-2485 to schedule.
We Also Serve Cities Near Broadview Park
Our crews cover the full South Florida region from the Miami coordination office. We regularly install and service gates in Jacksonville, Miami, Tampa, and Orlando, with the same Garrison Standard applied at every location. If you’re searching for Gate Installation in Broadview Park and need service at a second property elsewhere in Florida, one call handles both.
Serving Broadview Park, FL – Our Local Coverage Area
We’re based in the Broadview Park area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Installation in Broadview Park
We typically schedule measurements in Broadview Park within 48 hours of your call, and often next-day if your schedule allows. Call (469) 530-2485 and we’ll find a window that works. Estimates are free and there’s no obligation.
Yes. We install gates throughout Broadview Park, including homes off Peters Road, near the Middle River canal, and in the areas around Southwest 31st Avenue. If your address is in the 33317 ZIP or adjacent, we serve it.
We don’t install gates same-day, that’s not how measured, permitted work happens. For emergency security needs, we can often install a temporary barrier or repair an existing gate same-day. Our Gate Repair in Broadview Park crew handles those calls 24/7.
Material costs are similar across Florida, but Broadview Park’s sandy soil and salt-air exposure sometimes require upgraded hardware and deeper footings that add $200 – $400 to a typical residential job. We factor that into your written price during measurement, not after.
Every installation carries our 365-Day Done Right Promise. If anything fails due to workmanship or defective parts within one year of installation, we return and fix it at no charge. The guarantee is in writing on every job, not a verbal promise.
Written by Lonnie Burke, Owner at Carver Gate Repair, serving Broadview Park and South Florida since 2008.