Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Des Moines, WA
Gate work in Des Moines runs into conditions most Seattle-area technicians never deal with: salt air off Puget Sound, steep driveways cut into the hillside, and older gate systems that were installed before modern safety sensors became standard. Carver Gate Repair handles all of it, from a swing gate that won’t close on a Redondo waterfront property to a slide gate motor that’s seized up on Marine View Drive. If your gate isn’t opening, isn’t closing, or isn’t responding, call (469) 530-2485 and you’ll get a live person who can get a technician to your Des Moines home.
Why Des Moines Homes Are Different
Des Moines sits on a slope running down to the Sound, which means two things for gates. First, the grade. Many driveways in the Zenith and Woodmont neighborhoods climb steeply, so a gate that sags even two inches will drag on the concrete. Second, the salt. Homes west of Pacific Highway South, especially in Redondo and around Saltwater State Park, get enough marine exposure that steel hinges and track hardware corrode faster than they would in Kent or Renton.
The housing stock here runs from 1960s ramblers in the Midway area to newer construction along the water, and the gate equipment matches that range. We see a lot of FAAC and Viking swing operators on older Des Moines properties, while newer homes tend toward LiftMaster and BFT. The common thread is that many systems were installed when the house was built and haven’t been touched since. Limit switches wear out, loop detectors stop reading vehicles, and articulating arms lose their adjustment. None of that is a reason to replace a gate. It’s a reason to call someone who knows the equipment.
Our Main Des Moines Services
Most Des Moines homeowners call us for one of two reasons: a gate that has stopped working, or a gate they want installed. Here’s what each job looks like in this city.
Gate Repair in Des Moines
Repair work in Des Moines usually comes down to three things: a hinge or wheel that’s failed, a motor that’s stopped responding, or safety sensors that have been knocked out of alignment by wind or a vehicle. On hillside properties, we also see gates that have shifted on their posts as the ground settles. Our technicians troubleshoot the whole system, write up the price, and do the work only after you’ve approved the number. For the full breakdown of what gets repaired and how we stage the work, see Gate Repair in Des Moines.
Gate Installation in Des Moines
A new gate in Des Moines has to be built for the specific site. That means measuring the slope, checking how close the driveway is to the property line, and planning the operator around the gate’s actual weight and swing path. Woodmont and Zenith lots often have less room at the curb than homeowners expect, which affects whether a sliding or swinging gate makes sense. We quote the full job in writing, down to the post depth and operator model. Details on materials, timing, and the process are on Gate Installation in Des Moines.
Gate Motor Repair in Des Moines
When a motor fails in Des Moines, the cause is frequently water intrusion or a limit switch that’s gone out of adjustment, especially on systems within a mile of the water. We service FAAC, BFT, Linear, and Viking operators on site, and we carry the replacement parts for common failures in our vans rather than making you wait on a parts order. The repair gets a written one-year guarantee. For a complete look at motor problems and what they cost to fix, see Gate Motor Repair in Des Moines.
What happens when you call
- 1
A real person answersNo phone trees – you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Des Moines
Our technicians work on the brands most common in Des Moines: FAAC, BFT, Linear, and Viking among them. We keep the usual failure parts in stock at the local dispatch, so a motor repair doesn’t have to wait on shipment. For the full list of what we service, see our brands.
Pricing for Gate Company in Des Moines, WA
| Service | Typical range in Des Moines |
|---|---|
| Gate repair (hinges, alignment, track) | $180 – $340 |
| Gate motor replacement | $450 – $1,200 |
| Swing gate operator install | $900 – $2,800 |
| Slide gate operator install | $1,200 – $3,500 |
| Safety sensor replacement | $150 – $350 |
| Limit switch adjustment or replacement | $120 – $260 |
| Loop detector replacement | $200 – $450 |
| Remote/keypad programming | $75 – $180 |
| Full gate installation | $2,500 – $12,000+ |
What pushes a Des Moines job toward the top of those ranges is usually terrain and corrosion. A gate on a steep Redondo driveway takes longer to level and anchor, and rusted track hardware on a waterfront property means more parts to replace. Whatever the job, the price is written down before work starts, and it does not change at the door.
Neighborhoods We Serve in Des Moines
We run calls across the full city, from the waterfront streets of Redondo to the hills above Zenith and the flatter blocks near Midway. Our technicians are typically able to reach most Des Moines addresses within a couple hours on a repair call.
- Redondo
- Woodmont
- Zenith
- Midway
- Marina District
Service Area – Cities Near Des Moines
Our Des Moines crews also cover the surrounding Puget Sound area. We regularly run gate calls in Seattle, WA, down through Tacoma, WA, and out to Spokane, WA and Vancouver, WA when the job calls for it. If you’re in one of those cities or anywhere close, the same written-price and one-year guarantee applies.
Serving Des Moines, WA – Our Local Coverage Area
We’re based in the Des Moines area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Des Moines
Most repair calls in Des Moines are reached the same day, and emergency calls are dispatched as soon as a truck is available. For a gate that won’t close, we treat it as urgent since a standing-open gate leaves your property exposed overnight.
Repair work on an existing gate generally does not require a permit. New installations can, depending on the gate’s height and location, and some Des Moines HOAs have their own design rules. We’ll flag what applies to your property before any work starts.
We cover all of Des Moines, including Redondo, Woodmont, Zenith, Midway, and the Marina District. If you’re just outside the city line, call us and we’ll tell you whether we can schedule your job. Phone coverage is live around the clock.
Contact Carver Gate Repair in Des Moines
If your gate is down, making noise, or just not behaving, call (469) 530-2485. You’ll get a live person, a straight answer, and a written price before any work begins. Lonnie Burke leads our crews, and every technician arrives background-checked and in uniform. We serve all of Des Moines, and every repair carries our written one-year guarantee.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Des Moines Customers Say
"Straight answers on whether to repair or replace the operator. Repair was the right call."
- Wanda F."Gate hinge was bending under the weight. Welded a new bracket on and re-hung it. Solid now."
- Rudy A."Slide gate wasn't opening fully. Veteran tech found a worn drive chain and a misaligned limit. Fixed both in one visit."
- Don H.