Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Manhattan
Gate installation in Manhattan comes with constraints most contractors never think about: 20-foot-wide brownstone lots, fire-escape clearances, DOB filing requirements, and freeze-thaw cycles that destroy poorly set posts. Carver Gate Repair handles these daily. We install driveway gates, pedestrian gates, sliding gates, swing gates, double gates, and security gates across Manhattan with written pricing agreed before any work begins, background-checked technicians, and a 365-day guarantee in writing on every repair. If you need a new gate or a full replacement, call (469) 530-2485 and you’ll reach a live person, not a voicemail box.
Why Carver Gate Repair Is Manhattan’s Preferred Gate Installation Company
Manhattan homeowners don’t have room for error. A swing gate that arcs into a sidewalk on East 9th Street isn’t an inconvenience; it’s a liability. That’s why our crews operate to The Garrison Standard: written prices, clean job sites, and a full-year guarantee on every installation and repair. Lonnie Burke leads our team, and every technician dispatched to Manhattan arrives background-checked and in uniform, so you know exactly who you’re letting through the gate.
We cover the whole borough, from Inwood and Washington Heights down through Harlem, the Upper East Side, Midtown, Chelsea, the West Village, the East Village, the Lower East Side, and Battery Park City. When a property manager in Tribeca calls about a failing gate operator on a parking entrance, we send a technician who has worked on that exact brand before. Not a generalist who’ll figure it out on your dime.
Response time to Manhattan is coordinated from our New York City office, so dispatch runs close. For emergency gate failures, our phones are staffed by a live person 24/7, including weekends and holidays. We stock common parts locally for the brands Manhattan properties already run: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
Automatic Gate Installation in Manhattan
Automatic Gate Installation in Manhattan means engineering for tight clearances, pedestrian traffic, and building code. A new automatic swing gate on a Chelsea townhouse courtyard requires more than bolting an operator to an existing post. The hinge post footing has to be poured deep enough to survive freeze-thaw cycles without shifting. The operator needs a dedicated circuit, not a tapped line from an old basement panel. Safety photocells and a reversal edge have to be installed and tested per UL 325 entrapment standards.
For a typical Manhattan property, a new automatic gate installation runs $4,800 to $11,000 depending on gate width, operator type, and electrical work. That figure includes excavation and concrete footing for the hinge post, mounting the operator, running power, installing the safety edges and photocells, and testing everything before we leave. We don’t promise same-day installation. A proper job takes a full day, sometimes two.
Driveway and Courtyard Gate Automation
In Manhattan, most “driveways” are actually rear courtyards, loading zones, or private parking slots behind walk-up buildings. We install swing gate operators, sliding gate motors, and keypad or intercom entry on these tight lots. The operator has to swing into space that often butts against a building wall or a sidewalk, so we measure arc clearance before we ever order parts.
Pedestrian Gate Automation
Pedestrian gates in Manhattan often get automated for security, not convenience. Think of a ground-floor apartment walkway in Harlem or a rear service gate in the East Village. We install keypad entry, card readers, and intercom systems tied to small swing operators. Wiring typically requires a dedicated low-voltage run, which we handle in-house.
Gate Installation Services in Manhattan
Gate Installation Services in Manhattan cover new gate fabrication, steel and aluminum frame gates, full post replacement, and complete automation packages. We handle the whole job: demolition of the old gate, excavation for new footings, setting posts in concrete, hanging the new gate, running power and low-voltage wiring, mounting the operator, and programming entry systems. You get one crew, one written price, and one guy to call if anything’s off.
A new manual steel gate on a Manhattan townhouse runs $2,800 to $6,500 including new posts. Adding automation typically brings the total to $4,800 to $11,000. When we quote a job, we walk the site first. We don’t give phone quotes for Manhattan because every lot is different: setback depth, soil conditions, existing concrete thickness, and electrical access all change the number. What we quote in writing is what you pay. The price never moves at the door.
Security Gate Installation
Security gates in Manhattan serve two purposes: keeping people out and satisfying insurance and building requirements. We install steel security gates for ground-floor retail, rear courtyard access, and rooftop mechanical areas. Frames are welded or bolted to structural steel, never just lagged into brick. A security gate installation in Manhattan typically runs $5,000 to $12,000 depending on size, material, and whether it needs a motor.
Sliding Gate Installation
Sliding gates make sense on Manhattan lots where a swing gate would arc into a sidewalk or a fire escape. We install cantilever slide gates on a track system, which requires a concrete pad for the track and a well-built support post at the open position. Sliding gate systems are more involved than swings, often running $6,500 to $13,000 with automation.
What happens when you call
- 1
A real person answersNo phone trees – you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Manhattan
Carver Gate Repair technicians work on nine gate-motor brands, and we stock parts locally for Manhattan properties. That includes Viking swing operators, Ghost Controls systems, DoorKing slide and swing motors, and Elite gate openers. Why does brand matter? Because a DoorKing operator on a parking gate in Tribeca has different wiring, limit switch, and control board logic than a Ghost Controls unit on a townhouse courtyard in the West Village. Our technicians know the difference before they open the panel. When a Manhattan customer calls about a gate operator that won’t open or won’t close, we often have the right board, limit switch, or loop detector on the truck the same day.
Common Gate Installation Problems We See in Manhattan Homes
- Hinge post deterioration from freeze-thaw and road salt. Manhattan winters kill gate posts. Water seeps into the concrete footing, freezes, expands, and cracks the base. The gate starts sagging within two or three seasons. Adjusting the hinges won’t fix it. The footing has to be demolished and re-poured, and that’s a job we do regularly across the borough.
- No dedicated circuit for the gate operator. Older brownstones and walk-ups in neighborhoods like the Lower East Side and Harlem often have electrical panels that were never sized for automatic gate operators. Tapping an existing circuit leads to voltage drop, battery drain on solar units, and premature motor failure. We run a dedicated circuit on every automatic install.
- Missing or untested safety photocells and edge sensors. On tight Manhattan lots, a swing gate can hit a pedestrian, a parked car, or a building wall. UL 325 requires entrapment protection, and DOB inspections will fail without it. We install and test photocells and reversal edges on every automatic gate, and we document the test results.
- Gates built without fire-escape clearance. Many Manhattan buildings have fire escapes that extend into the rear yard. A gate installed in the wrong position can block that egress, which is a violation and a real safety hazard. We check clearance before we set a single post.
Pricing for Gate Installation in Manhattan, NY
Here are honest numbers for Manhattan gate work. A manual steel gate replacement runs $2,800 to $6,500 including new posts. A full automatic gate installation with operator, keypad, safety edges, and wiring runs $4,800 to $11,000. Sliding gate systems start around $6,500 and go up from there based on gate width and track length. Security-grade steel gates for retail or parking access run $5,000 to $12,000. Every quote is in writing, delivered before work starts, and the number doesn’t change. Call (469) 530-2485 for a free estimate. We walk the site in Manhattan, measure everything, and hand you a written price on the spot.
We Also Serve Cities Near Manhattan
While this page is for gate installation in Manhattan, our crews also cover the surrounding boroughs and nearby towns. If you’re in Brooklyn, Staten Island, the Bronx, or Mount Vernon, the same crew, the same written pricing, and the same 365-day guarantee apply. See our full Gate Installation in Manhattan coverage details, or call (469) 530-2485 and we’ll route you to the right technician for your neighborhood.
Looking for more detail on what a new gate project involves? Visit our Gate Installation service hub for the full breakdown of materials, operators, and what to expect on install day.
Serving Manhattan, NY – Our Local Coverage Area
We’re based in the Manhattan area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Installation in Manhattan
Yes. Most Manhattan properties don’t have a traditional driveway. We install gates on rear courtyards, walk-up service entrances, ground-floor patios, and parking slots with only a few feet of setback. The key is choosing the right gate type: a sliding gate or a properly sized swing gate with an articulating arm operator often works where a standard swing operator won’t fit. We measure the actual clearance before we recommend anything, and we account for fire-escape egress and sidewalk overhang. Call (469) 530-2485 for a site walk and a written estimate.
A standard single swing gate installation in Manhattan takes one full day. That includes demolition of the old gate, excavation for new hinge post footings, setting posts in concrete, hanging the new gate, running power, mounting the operator, and testing the safety edges and photocells. Sliding gates and double gates take two days, sometimes more, depending on the concrete work and electrical access. We don’t promise same-day installation because proper concrete curing and UL 325 entrapment testing can’t be rushed. We’ll give you a firm schedule before we start.
Often, yes. The NYC Buildings code treats many residential gates as fences subject to a 4-foot height limit unless the property sits in a landmark or commercial zoning context. Some installations require DOB filing, and some require an electrical inspection if we’re running a new dedicated circuit. We’ll tell you upfront whether your project requires paperwork. We handle the filing and coordinate inspections where needed, so you’re not left wondering if the job is legal.
We install and service nine brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That matters in Manhattan because existing properties run different systems. A Ghost Controls unit on a West Village townhouse needs different programming than a DoorKing slide operator on a Tribeca parking entrance. Matching the brand to the existing wiring and access control system saves you from rework and failed inspections. Call (469) 530-2485 and tell us what’s on your gate now.
Yes. A sagging gate in Manhattan is almost always a failed hinge post footing, not a panel problem. Freeze-thaw cycles and road salt corrode the post base and crack the concrete. During a new installation, we demolish the old footing, pour a new one, and set a proper steel post before hanging the new gate. We don’t put a new panel on a bad post. That would just sag again in two winters, and we guarantee our installs for a full year, so we do the footing right the first time. Call (469) 530-2485 for a free estimate on the full replacement.
Contact Carver Gate Repair in Manhattan
If you’re in Manhattan and need a new gate, an automatic operator, or a full replacement, call (469) 530-2485. You’ll get a live person, a straight answer, and a free estimate with a written price before any work starts. We serve every neighborhood in Manhattan, from Inwood to Battery Park City, with background-checked technicians and a 365-day written guarantee on every job. No voicemail queues. No number that moves at the door.
Written by Lonnie Burke, Owner at Carver Gate Repair, serving Manhattan with The Garrison Standard since 2008.