Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor Repair Across Burbank
Gate motor repair in Burbank typically costs between $225 and $620 depending on whether the issue is a limit switch, control board, or a full operator replacement. Most repair calls we handle in Burbank are completed in a single visit, and every job starts with a written price before any work begins. We know the streets, the housing stock, and the specific ways gates fail here. If your gate won’t open, reverses mid-travel, or the keypad stopped responding, call (469) 530-2485 and a real person will pick up.
Why Carver Gate Repair Is Burbank’s Preferred Gate Motor Repair Company
Burbank homeowners call us because we show up when we say we will, and the price we quote is the price on the invoice. That’s The Garrison Standard, and it has been the operating rule since 2008. Our technicians are background-checked and uniformed, so when one of our trucks pulls up to a home off Glenoaks Boulevard or Magnolia Boulevard, there’s no question about who’s walking onto the property.
We work exclusively on gates and gate motors. That focus means our techs know the failure patterns of LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems from the inside out. It also means we stock the common parts for those brands, so we’re not making a Burbank customer wait three days for a control board that every other shop has to special-order.
Every repair carries a written 365-Day Done Right Promise. If a repair fails inside the guarantee window, we come back at no charge. It’s in writing, not a verbal assurance. For a homeowner who has already been burned once by a no-show or a moving price, that matters more than any marketing language ever could.
Gate Keypad in Burbank
Gate Keypad failures in Burbank are among the most common calls we take, and they usually have nothing to do with the motor itself. A keypad that stopped working is often a wiring issue at the hinge post, a corroded terminal strip from Burbank’s summer heat and smog exposure, or a dead keypad that simply needs replacing and reprogramming into the operator’s control board. We diagnose the actual cause rather than replacing parts on a hunch.
When we replace or install a gate keypad in Burbank, the work includes running or repairing the low-voltage wiring, programming entry codes, and verifying the keypad communicates cleanly with the operator. The cost for a standard keypad replacement in Burbank runs $180 to $340. A full keypad installation with new wire runs can reach $450 to $600 depending on distance from the operator and whether conduit needs to be added.
Wired Keypad Replacement
A wired keypad that has failed due to moisture or age gets swapped with a new unit matched to the existing operator brand. We test it at the panel and at the gate before we leave, so you’re not standing in the driveway wondering if it’ll work tomorrow.
Wireless Keypad Installation
For gates where running wire is impractical or the original conduit is damaged, we install wireless keypads that pair directly with the operator. These run on battery power and are programmed on-site with your codes.
Gate Closer Spring in Burbank
Gate Closer Spring failures in Burbank are common on older swing gates, especially where the original gate was built as a lighter wood panel and later retrofitted with a heavy operator. The closer spring bears the gate’s weight through every cycle. When it breaks or loses tension, the gate slams or drifts, and the operator’s motor works harder to compensate, which shortens the motor’s life.
A gate closer spring replacement in Burbank typically costs $140 to $275 including parts and labor. If the spring has been failed for a while and the operator has been straining against it, we’ll also check the gears and belt for premature wear during the same visit. We stock common spring sizes for FAAC and BFT swing operators, which are the two brands we see most often on Burbank’s mid-century swing gates.
Spring Tension Adjustment
Sometimes the spring isn’t broken, just under-tensioned. We measure the gate’s pull weight and adjust the spring to the manufacturer’s spec, which restores smooth travel and takes the strain off the motor.
Heavy-Duty Spring Conversion
When a gate has outgrown its original spring, we convert to a heavier-gauge spring rated for the gate’s actual weight. This is common on ornamental steel gates that replaced original wood panels but kept the old hardware.
Trusted Brands We Service in Burbank
Our technicians are trained on nine gate-motor brands, and in Burbank we most often service FAAC, BFT, Linear, and Viking systems. That covers the majority of swing and slide operators installed across Burbank’s residential neighborhoods, from the hillside properties near Stough Canyon to the flat lots along Chandler Boulevard. Because gate work is all we do, we stock local parts for these brands, which means faster turnaround when a control board or limit switch needs replacing. We don’t have to order from a distributor and ask you to wait.
Common Gate Motor Repair Problems We See in Burbank Homes
- Intermittent reversal on swing gates: Much of Burbank’s gate repair density tracks its pre-1960 single-family housing stock, where original block walls and concrete gate piers commonly have shallow post footings poured for lighter wood gates. As soon as a heavier operator goes on, the footing becomes the failure point. The post shifts under load, and the safety sensors read the movement as an obstruction.
- Premature gear and arm wear from sagging panels: A sag correction attempted at the gate panel instead of the post means the operator keeps straining against misalignment. We see the rack and pinion or articulating arm on Burbank’s older ornamental gates worn out long before the motor itself fails.
- Non-compliant additions: A keypad or safety photocell installed without verifying UL 325 entrapment protection leaves the system unsafe and legally non-compliant. We come across this regularly on gates where a handyman or generalist added a feature without testing reversal force.
- Control board failures from heat exposure: Burbank’s summer temperatures regularly push past 100°F in July and August, and control boards mounted in unventilated metal cabinets cook over time. Capacitors degrade, and the board eventually fails to communicate with remotes or the keypad.
Pricing for Gate Motor Repair in Burbank, CA
Here are the numbers we actually quote for Burbank homeowners. A limit switch replacement runs $160 to $240. A control board replacement runs $280 to $520 depending on brand. A full operator replacement, including removal of the old unit and installation of the new one, runs $850 to $1,700 depending on gate weight, operator type, and whether the existing mounting can be reused. A service call with diagnosis runs $85 to $120, and that diagnosis fee is credited toward the repair if you proceed with the work.
Every price is written down before we touch the gate. If we find something else while the job is open, we stop, explain what we found, and give you a new written number before continuing. No surprises at the invoice.
Call (469) 530-2485 for a free estimate. We’ll tell you what the repair should cost before we even schedule the truck.
We Also Serve Cities Near Burbank
Our gate motor repair crews cover Burbank and the surrounding areas, including Glendale, West Hollywood, Altadena, and Beverly Hills. If you’re in one of those cities and your gate has stopped working, the same Gate Motor Repair team that serves Burbank can help. Learn more about our full coverage at Gate Motor Repair in Burbank or call (469) 530-2485.
Serving Burbank, CA – Our Local Coverage Area
We’re based in the Burbank area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Motor Repair in Burbank
The most common cause we find in Burbank is a shifting post footing on older block-wall construction, not a motor fault. When the hinge post moves under load, the safety sensors interpret the misalignment as an obstruction and reverse the gate. We correct the footing, re-aim the photocell, and the problem stops. Call (469) 530-2485 and we’ll diagnose it properly.
No, and we won’t promise that. A proper operator installation in Burbank involves measuring the gate, assessing the post and footing, ordering the correct operator for the gate’s weight and travel, and scheduling the install. Rushing that process produces worse results. What we do promise is a free measure and a written price so you know exactly what the installation will cost before you commit.
Usually not. A dead keypad is most often a wiring failure, a corroded terminal, or the keypad itself. The motor is often fine. We’ll test the keypad circuit independently of the operator so you don’t pay for a motor repair you don’t need. A keypad replacement in Burbank runs $180 to $340.
Many do. Burbank’s pre-1960 homes often have gate piers with shallow footings poured for original wood gates. Adding a heavier operator or a solar gate opener to that footing is how we end up with intermittent reversal and premature gear wear. We assess the footing before quoting the operator install, and if it needs reinforcing, we tell you and write it into the price. We don’t install a new operator on a failing footing and call it done.
A proper repair includes diagnosing the actual fault, replacing or repairing only what’s failed, testing the full travel cycle, verifying UL 325 entrapment protection and reversal force, and confirming the remotes and keypad communicate correctly. It also includes a written price before work starts and a written guarantee after. That’s what our crew delivers on every Burbank call.
If your gate motor is acting up in Burbank, call (469) 530-2485. A live person answers, we’ll schedule a time that works for you, and you’ll get a written price before any work begins. No voicemail, no call-back queue, and no number that changes at the door.
Written by Lonnie Burke, Owner at Carver Gate Repair, operating to The Garrison Standard since 2008.