Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor Repair Across Clovis
When a gate motor fails in Clovis, you need a technician who understands what actually breaks here. Dust from ag-adjacent properties, hard water from the Fresno-area supply, and aging underground conduit on 1970s-90s tract lots all create failures that a generic motor swap won’t fix. Carver Gate Repair serves all of Clovis with background-checked, uniformed technicians who diagnose the full system before replacing anything. We answer the phone live, 24/7. Call (469) 530-2485 when your gate won’t move, won’t stop, or starts reversing on its own.
Why Carver Gate Repair Is Clovis’s Preferred Gate Motor Repair Company
Homeowners in Clovis call us because the process is predictable. You get a written price before any work starts, a written guarantee on every repair, and a technician who arrives in a uniform and introduces himself before touching the gate. Lonnie Burke leads our crew, and he holds every job to The Garrison Standard: written prices, background-checked technicians, and a full-year guarantee. No exceptions.
We carry parts for the brands most common on Clovis gates: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That means we don’t have to order a control board and make you wait a week. If your operator is one we stock, we can usually complete the repair on the first visit. If the repair fails inside the guarantee window, we come back free. No charge, no argument.
Our dispatch and scheduling for Clovis is coordinated from the Fresno office, but the crew serving Clovis works these streets every week. We know the difference between a Buchanan-area lot with orchard-adjacent dust and a newer Clovis Unified-area build with fresh conduit. That local knowledge changes the diagnosis.
Gate Operator Repair in Clovis
Gate operator repair in Clovis means fixing the motor, the control board, the limit switches, and the safety system that drives your gate. It’s not just swapping a motor. When we diagnose an operator, we test the full run path, check the entrapment protection, inspect the wiring from panel to gate, and look at what’s been failing locally: mineral-scaled boards, dust-packed photo-eyes, and aged conduit.
Control Board and Limit Switch Work
Clovis hard water leaves mineral crust on control boards, especially where irrigation overspray reaches the enclosure. A board that’s scaled will send phantom signals: gate opens halfway, reverses, or won’t take a keypad code. We clean, reseal, and replace boards rather than guessing at the motor first.
Full Operator Replacement
When an operator is beyond repair, we replace it with a unit matched to your gate’s weight, swing or slide type, and power supply. We quote the replacement in writing before any work starts. Typical operator replacement on a Clovis single-swing gate runs $850 to $1,600 depending on brand and access.
Gate Motor in Clovis
When a Clovis homeowner says the gate motor is dead, the cause is often upstream of the motor itself. We check power at the panel first, then at the gate. On older Clovis tract lots from the 1970s-90s, the underground conduit feeding the motor has been in the ground for decades. Root intrusion, irrigation shorts, and shifting soil after a driveway pour all break that wiring. The motor tests fine on the bench and dead at the gate.
Motor Diagnosis vs. Replacement
A motor can fail mechanically: stripped gears, worn brushes, seized bearings. But a motor that barely moves may just be getting low voltage through corroded wire. We test voltage under load. If the motor is sound, we repair the feed. If the motor is shot, we replace it. A typical gate motor replacement in Clovis runs $450 to $900 for the motor itself, plus labor.
What a Proper Repair Includes
Every gate motor repair ends with entrapment testing. The gate must reverse under resistance, the photo-eyes must detect an obstruction, and the limit switches must stop the gate where it’s set. If you skip the safety testing, you’ve got a gate that moves and a liability you don’t want. We test it every time.
Trusted Brands We Service in Clovis
We work on nine gate-motor brands, including Gate Motor Repair on Linear, Viking, and DoorKing systems that are common on Clovis homes. We keep local stock of control boards, remotes, photo-eyes, and limit switches for these brands specifically because Clovis customers shouldn’t wait on a warehouse shipment when a gate is stuck open. If we don’t have the part on the truck, we source it same-week from the Fresno supply chain. You get the diagnosis in writing, the price in writing, and the repair with a full-year guarantee.
Common Gate Motor Repair Problems We See in Clovis Homes
- Ag-belt dust in boards and photo-eyes. Clovis sits next to active agriculture, and the fine dust gets into control board enclosures and photo-eye lenses. The gate reverses for no reason, or won’t close. We clean, reseal, and realign before replacing anything.
- Mineral scale from hard water. Irrigation overspray and hard water leave crust on limit switches and board contacts. Keypad entry dies, or the gate stops mid-travel. We dissolve the scale and add a sealed enclosure where needed.
- Failing underground conduit. Tract homes built in the 1970s-90s across Clovis ran direct-burial wire to gate posts. Irrigation water, roots, and age short the feed. The operator tests fine at the panel but not at the gate. We locate the fault and run new conduit where the old run is shot.
- Loose hinge posts after a driveway pour. When a driveway is poured first and the gate post goes in after, the soil under the post was disturbed. A repaired swing gate sags again at the post. We reset and re-anchor the post before hanging the panel.
Pricing for Gate Motor Repair in Clovis, CA
A gate motor diagnostic in Clovis typically runs $89 to $129. A control board replacement is $300 to $650. A full gate motor replacement runs $450 to $900 for the motor, with labor bringing most single-swing jobs to $850 to $1,400 total. Slide gate operators run higher: $1,200 to $2,200 installed. Every price is written down before work starts. If we find more work during the job, we stop, show you the problem, and get your approval on a new written price before continuing. Call (469) 530-2485 for a free estimate.
We Also Serve Cities Near Clovis
Our Clovis crew also covers the surrounding Central Valley cities. If you’re in Fresno, Sanger, Fowler, or Madera, the same written-price, written-guarantee process applies. See Gate Motor Repair in Clovis for the full service area and what to expect on a call.
Serving Clovis, CA – Our Local Coverage Area
We’re based in the Clovis area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Motor Repair in Clovis
The motor is getting power but the gate isn’t transferring motion, which usually means stripped gears, a worn drive belt, or low voltage through corroded conduit. On older Clovis tract lots from the 1970s-90s, the underground feed to the gate motor is the most likely culprit. We test voltage under load at the motor before condemning anything. Call (469) 530-2485 and we’ll diagnose it on-site.
Yes. California gate installations require entrapment protection, and a photo-eye that’s misaligned or dust-packed from ag-adjacent air will make your gate refuse to close or reverse on its own. We clean, align, and test the photo-eyes on every gate motor repair in Clovis, and we replace sun-warped brackets with a sturdier mount.
Yes, if the gate panel, hinges, and post are sound. We match the new operator to the gate’s weight and travel type, and we use the existing mounting points where possible. If the post is loose or the wiring is failing, we address that in the same visit and put it on the written quote before we start.
Phantom openings are usually a control board picking up stray signals or mineral scale bridging contacts on the board. Hard water from the Clovis supply and irrigation overspray are common causes. We clean and reseal the board first, then test the keypad and receiver. If the board is beyond cleaning, we replace it for $300 to $650.
Most gate motor repairs in Clovis are done in one visit, taking 2 to 4 hours on-site. New gate or operator installations are scheduled work with a written timeline, not a same-day promise. We’ll give you a date and a price in writing before the job starts, and if the repair fails within a year, we return free.
Call Carver Gate Repair for Gate Motor Repair in Clovis, CA
If your gate won’t close, won’t open, or is behaving erratically, call (469) 530-2485. You’ll speak to a live person, not a voicemail queue. We’ll schedule a technician for Clovis, give you a written price before any work starts, and back the repair with our 365-Day Done Right Promise. If it’s not done right, we make it right. Free estimate, clear price, no surprises at the door.
Written by Lonnie Burke, Owner at Carver Gate Repair, serving Clovis and the Central Valley since 2008.