Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Kennedale
A gate that won’t open, sags on its hinges, or drags across the driveway isn’t a tomorrow problem in Kennedale. It’s the kind of thing that traps your truck when you’re already late for work, or leaves your property open all night after a spring storm rolls through Tarrant County. Our Gate Repair crews are dispatched from our Dallas-Fort Worth office and carry parts for nine motor brands, so most Kennedale calls finish in a single visit. Call (469) 530-2485 and you’ll reach a live person, not a voicemail box, any hour of any day.
Why Carver Gate Repair Is Kennedale’s Preferred Gate Repair Company
We’ve worked on gates along Kennedale’s older ranch-style properties off Little School Road and the newer subdivisions near Kennedale High School. That mix of housing stock means one call might involve a 1980s chain-link swing gate with rusted posts, and the next a modern FAAC articulating arm on a wrought-iron driveway gate. We’ve seen both, and we stock parts for both.
Kennedale sits on the edge of the Cross Timbers ecological region, where the black clay soil shifts dramatically between wet springs and dry Augusts. That ground movement is hard on gate posts. We’ve replaced posts in Kennedale that leaned six inches off plumb after a single rainy season, and we’ve realigned gates on Kennedale Parkway that had been binding for months because the homeowner assumed the motor was failing when the problem was actually post settlement.
Our technicians are background-checked, uniformed, and arrive in marked vehicles. Every repair comes with a written price before work starts and a 365-Day Done Right Promise in writing. If something fails inside that year, we come back free. No argument, no re-diagnosis fee.
Phones are answered by a live person 24 hours a day, including weekends and holidays. That’s not a marketing claim. It’s how The Garrison Standard operates, and it’s how we’ve worked since 2008.
Wood Gate Repair in Kennedale
Wood Gate Repair in Kennedale, TX typically addresses sagging frames, rotted bottom rails, and hinge failures caused by our humid springs and summer heat cycles. A typical wood gate repair in Kennedale runs $180 – $450 depending on whether we’re replacing hardware, sistering a frame, or rebuilding a section. Most wood gates we see in Kennedale are cedar or pressure-treated pine, and both species move with moisture changes in ways that stress joints and fasteners.
Frame Reinforcement and Sag Correction
A wood gate that drags or won’t latch usually has a frame that’s twisted or a rail that’s pulled loose from its stile. We square the frame, replace stripped screws with through-bolts where appropriate, and add a steel cross-brace or Z-brace if the original diagonal has failed. For Kennedale’s heavier cedar gates, we often upgrade to heavy-duty ball-bearing hinges that carry the load without the squeak and bind of standard hardware.
Bottom Rail and Post Rot
Wood gates in Kennedale contact soil or sit close to sprinkler lines more often than they should. Once moisture wicks into the end grain, rot follows fast in our climate. We cut out damaged sections, treat the remaining wood with borate preservative, and splice in pressure-treated or composite replacement material. If the post itself is compromised, we set a new post on a concrete footing that sheds water, not collects it.
Driveway Gate Repair in Kennedale
Driveway Gate Repair in Kennedale, TX covers everything from single-family swing gates on subdivisions near Pleasant Ridge to dual-slide systems on larger lots toward the Mansfield city limits. A typical driveway gate repair in Kennedale runs $220 – $680 for mechanical issues, with motor or control board replacement pushing toward the higher end. Most calls involve either the gate not responding to remotes, the motor running but the gate not moving, or the gate reversing for no apparent reason.
Operator and Motor Diagnostics
We test the operator under load, check limit switch positioning, and verify loop detector function before quoting any part. Kennedale’s electrical supply can spike during spring storms, and we’ve replaced more than one control board after a nearby lightning strike. Our trucks stock replacement boards for Linear, Viking, and FAAC operators, so we’re not ordering parts and making you wait.
Track, Roller, and Alignment Issues
Slide gates depend on level track and free-rolling trucks. In Kennedale, where driveways often have a slight crown for drainage, track can settle or shift. We re-level, re-weld track supports where needed, and replace worn V-groove or cantilever rollers. A gate that shudders or jams mid-travel usually has a mechanical problem, not a motor problem, and we diagnose that before suggesting any motor work.
Trusted Brands We Service in Kennedale
Our Kennedale repair crews carry parts and training for LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems. That range matters because Kennedale’s housing spans decades, and the gate motor installed in 2012 might be a brand that’s since changed hands or discontinued a control board. We stock common FAAC and BFT replacement arms, control boards, and receiver modules locally, so a failed operator doesn’t mean a two-week wait for shipping. If your gate uses a brand we don’t stock, we’ll tell you upfront and source the correct part with a clear timeline, not string you along.
Common Gate Repair Problems We See in Kennedale Homes
- Post lean from black clay expansion. Kennedale’s gumbo soil swells when wet and shrinks in drought, tilting posts that were set without proper depth or drainage. We reset posts on concrete piers with gravel backfill to break the capillary action that causes the cycle.
- Hinge seizure after pollen season. The oak and cedar pollen that coats Kennedale each spring works into hinge pins and bushings, mixing with humidity to form a gritty paste. Annual cleaning and lubrication prevents the galling that forces replacement.
- Storm damage to control electronics. Tarrant County spring storms bring power fluctuations and direct strikes. We install surge protection where appropriate and keep replacement control boards for common operators on our trucks.
- Rust-through on older wrought iron. Kennedale’s older neighborhoods have gates from the 1970s and 1980s with thin-wall tubing that rusts from the inside out. We cut and weld replacement sections, then apply a zinc-rich primer and industrial enamel that holds up to local UV exposure.
Pricing for Gate Repair in Kennedale, TX
Most gate repairs in Kennedale fall between $180 and $680. Hinge replacement and minor weld repair typically run $180 – $320. Post resetting or replacement with concrete footing runs $350 – $550. Motor or control board replacement ranges from $450 – $680 depending on brand and whether the existing wiring and safety edges are reusable. These are real numbers for Kennedale’s market, not teaser rates that change at your door.
What moves the price: gate material (iron, aluminum, wood, composite), access to the post or operator, whether the existing wiring meets current code, and whether the problem is one failed component or a cascade failure from deferred maintenance. We diagnose first, then give you a written price. You approve it before we touch a wrench. Estimates are free, and we don’t charge to show up and look.
We Also Serve Cities Near Kennedale
Our crews work throughout the southern Tarrant County area. If you’re in Kennedale or nearby Arlington, Mansfield, Burleson, or Fort Worth, the same live-answer phone line, same background-checked technicians, and same written guarantee apply. We also handle Gate Installation in Kennedale when repair isn’t economical, and Gate Motor Repair in Kennedale for operator-specific issues on automated systems.
Serving Kennedale, TX – Our Local Coverage Area
We’re based in the Kennedale area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Kennedale
Most Kennedale repair calls are scheduled same-day or next-day, with emergency response available when a gate is stuck open and compromising security. Call (469) 530-2485 for availability – a live person answers around the clock.
Yes. We repair gates throughout Kennedale, from the established homes near Little School Road and Kennedale Parkway to newer construction toward the Mansfield and Arlington edges. Our dispatch team knows the local street grid and sends the closest available technician.
Yes. Our phones are staffed by live operators 24 hours a day, every day of the year, including weekends and holidays. If your gate is stuck open, stuck closed, or damaged after a vehicle impact, we can dispatch an emergency technician to Kennedale.
Kennedale pricing sits in the same range as Arlington and Mansfield, slightly below central Fort Worth rates due to shorter travel times from our dispatch point. A typical hinge or post repair in Kennedale runs $180 – $450, comparable to neighboring markets. We don’t charge a premium for Kennedale calls, and we don’t quote one price over the phone and raise it at the door.
Every repair carries our 365-Day Done Right Promise in writing. If the same component or workmanship fails within one year of service, we return and fix it at no charge. No re-diagnosis fee, no argument. That’s The Garrison Standard, and it’s been our policy since 2008.
Written by Lonnie Burke, Owner at Carver Gate Repair, serving Kennedale since 2008.
Call (469) 530-2485 for a free estimate. A live person will answer, schedule a technician, and make sure you get a written price before any work starts.