Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Sunrise
A gate repair in Sunrise usually runs $185 to $420 for most mechanical and electrical fixes, while a full operator replacement lands between $850 and $1,900 depending on the motor and groundwork involved. We answer the phone around the clock, and our crews run calls across Sunrise from Sawgrass Mills to Weston Road. When a gate stops mid-travel or a motor burns out, you want a technician who knows Sunrise’s mix of older LiftMaster units and newer solar-charged openers, not someone learning on your driveway. Call (469) 530-2485 and you’ll get a live person, a written price before any work begins, and a crew that shows up in uniform with the parts already on the truck.
Why Carver Gate Repair Is Sunrise’s Preferred Gate Repair Company
Sunrise homeowners call us because we do one thing: gates. Not fences off to the side, not gates as an afterthought to a general handyman route. Our Gate Repair team carries parts for LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so the right component goes in the first time. When a Sunrise customer on Nob Hill Road reports a dead board on a 1996 Linear operator, we don’t spend two days sourcing it. We stock it.
Our technicians are background-checked and uniformed on every job, dispatched from our South Florida office to serve Sunrise directly. The Garrison Standard, in place since 2008, means every repair gets a written price before we touch a bolt, a written guarantee good for a full year, and a free second visit if the repair fails inside that window. No Sunrise homeowner has to argue for what was already promised. Lonnie Burke set that standard, and every crew member works to it.
Wood Gate Repair in Sunrise
Wood Gate Repair in Sunrise comes down to two things: the wood itself and the hardware holding it square. Many Sunrise homes in the 1980s-era neighborhoods off Sunset Strip were built with solid wood driveway gates that have now seen thirty-plus summers of humidity and afternoon downpours. The gate sags, the hinge post leans, the latch no longer lines up. We see it weekly. A wood gate repair in Sunrise typically runs $180 to $480 depending on whether we’re shimming hinges, replacing a rotted section, or rebuilding the post footing.
Hinge and Post Work
When a wood gate sags, the first suspect is rarely the gate leaf. It’s usually the post. Low-lying Sunrise yards hold water after heavy rain, and wood posts set without proper drainage rot at the base. We remove the rotted section, set a treated post or steel post in concrete, and re-hang the gate so it closes square. This runs $250 to $600 for a typical driveway gate.
Weld and Hardware Repair
Steel hardware on wood gates fails too. Hinges wear, latch strikes bend, and weld points crack from years of use. We repair or replace the hardware, then adjust the gate so the load sits evenly across the hinges. In Sunrise, we also see rust from the salt-adjacent humidity working on steel brackets faster than it does inland, so we treat the metal before we leave.
Driveway Gate Repair in Sunrise
Driveway Gate Repair in Sunrise usually starts with the operator, not the gate leaf. Homeowners in the gated sections off Hiatus Road and within the newer townhome clusters around 33323 often have automatic operators that have outlived their control boards. A driveway gate repair in Sunrise runs $220 to $520 for a board replacement, limit switch, or receiver issue, and $850 to $1,900 when the operator itself is shot and needs full replacement.
Operator Diagnostics and Board Repair
When a driveway gate won’t open, the failure is usually specific: a tripped limit switch, a blown capacitor, a control board that took a surge during one of Sunrise’s summer storms. We diagnose it on site, quote the repair in writing, and complete it the same visit in most cases. No vague “needs a new motor” without showing you the failed component.
Safety Edge and Loop Detector Calibration
Automatic gates in Sunrise must reverse when they hit something, and a gate that doesn’t is dangerous. We test every gate to UL 325 standards after a repair, not just the visible function. Loop detectors for vehicle exit and entry get re-calibrated so the gate opens when it should and doesn’t ghost-open at 2 a.m. because a sensor drifted.
Trusted Brands We Service in Sunrise
We work on the systems Sunset Sunrise homes actually have installed. Older FAAC hydraulic operators are common in the mid-90s estate sections, BFT units show up in the townhome gates around Sawgrass, and Linear and Viking operators run across the planned communities west of University Drive. We stock parts and know the failure patterns for each. That means a Sunrise customer with a FAAC 455D isn’t waiting a week for us to order a board. We match the part to the motor and get the gate back in service, fast turnaround included.
Common Gate Repair Problems We See in Sunrise Homes
- Dead control boards on aging LiftMaster and Linear operators: Sunrise’s 1980s and 1990s communities are full of operators at the very end of their service life. A summer of lightning-adjacent surges and voltage sags finishes them off, and the gate simply stops responding to the remote or keypad.
- Hinge post rot in low-lying yards: Sections of Sunrise drain slowly after heavy rain, and wood gate posts set decades ago are now losing their footing. The gate sags, the latch misaligns, and the problem gets misdiagnosed as a bad motthe by less focused technicians.
- Solar gate opener battery failure in shaded townhome clusters: Newer gated communities off Flamingo Road use solar-charged openers, but mature oak canopies keep the panels from full charge. The battery drains, the gate drags or stops mid-cycle, and the fix is a battery replacement plus a panel angle adjustment.
- Safety edge and photocell failures after storms: Sunrise thunderstorms bring wind-driven rain and debris that chafe wires and short out photocells at the hinge post. The gate then refuses to close, or worse, closes when it shouldn’t.
Pricing for Gate Repair in Sunrise, FL
The cost of gate repair in Sunrise breaks down by the job. A hinge shim and re-alignment runs $185 to $320. A safety photocell replacement with testing lands $160 to $280. Control board replacement on a Linear or LiftMaster unit runs $280 to $520. Full operator replacement, including the new motor, brackets, and safety-edge calibration, sits between $850 and $1,900 depending on the brand and whether new mounting or welding is needed. Solar opener battery replacement runs $140 to $260. Every customer gets a written price before work starts, and that price is what you pay. Estimates are free. Call (469) 530-2485 for an exact number on your gate.
We Also Serve Cities Near Sunrise
While this page focuses on Gate Repair in Sunrise, our crews also serve the wider region including Jacksonville, Miami, Tampa, and Orlando. If your property sits in one of those areas, the same Garrison Standard applies: written prices, background-checked technicians, and a full-year guarantee on every repair.
Serving Sunrise, FL – Our Local Coverage Area
We’re based in the Sunrise area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Sunrise
It’s almost always a repair, not a replacement. The failure is typically a dead safety edge sensor, a chafed photocell wire at the hinge post, or a control board that’s no longer reading the safety circuit. We replace the failed component and run a full UL 325 reversal test before we leave. Most safety circuit repairs in Sunrise run $160 to $320. Call (469) 530-2485 and we’ll diagnose it on site.
Yes, we service solar gate openers across Sunrise, especially in the newer gated townhome clusters where panels are common. The usual failure is a degraded battery that no longer holds a charge, often because shade from mature landscaping limits the panel’s output. We test the panel, replace the battery, and reposition or trim around the panel so the system keeps up with daily cycles.
Because the problem is almost never just the hinges. In Sunrise, the root cause is usually a wood hinge post rotting at ground level in a low-lying yard, or a footing that has shifted over decades of wet-dry cycles. Adjusting hinges without fixing the post gives you a square gate for a few weeks, then it sags again. We address the post and the footing, then re-hang the gate.
We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Sunrise’s housing stock spans older FAAC and Linear units in 1980s-90s communities and newer solar-charged openers in townhome clusters, so we stock parts across all of them. The right board for a FAAC 455D and the right battery for a Ghost Controls solar unit are both on the truck.
Yes. Many Sunrise properties have a wood pedestrian gate at the side yard and an automatic driveway gate at the front. We handle both in one visit, with one written price covering the full scope. Combining the jobs saves you the second trip charge and gets every gate on the property working under the same guarantee.
Call Carver Gate Repair in Sunrise
If your gate is sagging, stopping mid-travel, or refusing to respond to the remote, call (469) 530-2485. You’ll reach a live person, get a free estimate with a written price before any work starts, and have a background-checked, uniformed technician at your property who knows Sunrise’s gates from Sawgrass Mills to Weston Road. Every repair carries a written guarantee for a full year. If it fails in that window, the second visit is free. No argument, no fine print. That’s the standard Lonnie Burke set, and we hold to it on every job.
Written by Lonnie Burke, Owner at Carver Gate Repair, serving Sunrise residents with The Garrison Standard since 2008.