Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Keller, TX
Gate repair in Keller, TX comes down to three things: a gate that opens every time, a motor that doesn’t quit in July heat, and a technician who shows up when he says he will. Keller’s mix of acreage properties, established subdivisions, and newer master-planned communities means we see everything from 20-year-old swing operators on wrought iron to modern slide gates on new builds. Carver Gate Repair handles gate repair, gate installation, and gate motor repair for homes across Keller, with written prices and a one-year guarantee on every repair. Call (469) 530-2485 and a live person answers, day or night.
Why Keller Homes Are Different
Keller sits in the northeast corner of Tarrant County, and the housing stock spans several decades. Many homes in Marshall Ridge and the original Keller townsite were built in the 1990s and early 2000s, which means their gate motors and hinges are reaching the end of their service life around the same time. Newer developments along Bear Creek Parkway and in the western stretches near 377 trend toward larger lots, longer driveways, and heavier gates – slide gates become more common, and the operators have to work harder.
The clay soil Keller sits on shifts through wet and dry cycles. Gates that were perfectly level ten years ago may now bind at the latch or drag at the outer edge. A gate repair here often means adjusting hinge posts or re-hanging the gate leaf, not just swapping a part. We also see temperature swings that age capacitor-based openers faster than coastal climates do. When a motor hums but won’t start on a 100-degree afternoon, that’s frequently the cause.
HOA requirements matter in Keller. Many neighborhoods have architectural standards for gate style, height, and finish. Before a new gate goes in, the HOA usually wants to see the design. We help homeowners navigate that paperwork as part of the installation.
Our Main Keller Services
These are the three calls we take most from Keller homeowners. Each has its own page with pricing detail and local notes.
Gate Repair in Keller
Gate repair in Keller covers a lot of ground: sagging hinges, bent tracks, broken wheels, cracked welds, and gates that no longer close squarely. Many Keller gates are decorative steel with powder-coat finishes that hide rust until a weld finally gives. We grind out the failed weld, re-weld, and match the finish as closely as the coating allows. On swing gates, the hinge post itself may have shifted in the clay. That’s a Keller pattern we see more than other markets. Gate Repair in Keller covers the full range and what a typical call costs.
Gate Installation in Keller
A new gate in Keller starts with the driveway and the intended use. Long driveways off Bear Creek Parkway often call for a slide gate with a rack-and-pinion track. Shorter drives in neighborhoods like Hidden Lakes may do fine with a double swing. We measure the opening, check the grade, and spec the gate weight so the operator matches the load. The HOA submittal is part of the job – we hand you a spec sheet your architectural committee can approve. Gate Installation in Keller walks through materials, operator pairing, and a written quote process.
Gate Motor Repair in Keller
Motor repair in Keller usually starts with a call about a gate that opens but won’t close, or a keypad that flashes but the arm doesn’t move. We bench-test the control board, check limit switches, and inspect the capacitor and gear assembly. Heat is a real factor here – control boards mounted in metal boxes on west-facing brick walls take brutal sun. The fix is often a new board rated for the duty cycle. Gate Motor Repair in Keller lists common motor failures, our diagnostic process, and what a motor replacement costs in this market.
What happens when you call
- 1
A real person answersNo phone trees – you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Keller
Our Keller technicians carry parts for FAAC, BFT, Linear, and Viking systems, plus five other major gate-motor brands. The right part usually goes on in one trip because we stock the names that dominate Keller’s existing gate operators rather than ordering blind. See our brands for the full list and what we stock locally.
Pricing for Gate Company in Keller, TX
| Service | Typical range in Keller |
|---|---|
| Gate repair – minor (hinge adjustment, latch realignment) | $125 – $250 |
| Gate repair – moderate (weld repair, track realignment) | $250 – $450 |
| Gate repair – major (re-hang gate, replace frame section) | $450 – $850 |
| Gate motor repair – diagnostic call | $75 – $150 |
| Gate motor repair – control board replacement | $300 – $600 |
| Gate motor repair – full operator replacement | $800 – $1,800 |
| Gate installation – single swing gate with operator | $1,800 – $3,500 |
| Gate installation – slide gate with operator | $2,500 – $5,000 |
| Gate installation – custom driveway gate | $3,500 – $8,000 |
| Accessories – keypad, loop detector, or remote replacement | $150 – $400 |
Heavier gates, longer runs of track, and automation upgrades push pricing toward the top of these ranges. Every quote is written and given to you before any work starts, so the number on the page is the number on the invoice.
Neighborhoods We Serve in Keller
We run calls across the whole Keller footprint daily. Here are some of the neighborhoods we work in regularly:
- Marshall Ridge
- Hidden Lakes
- Keller Townsites and original Keller proper
- West Keller near Highway 377
- Bear Creek Parkway corridor
Same-week scheduling is typical for most Keller jobs, and emergency gate repair calls that need immediate attention can usually get a technician out same day.
Service Area – Cities Near Keller
Most of our Keller work comes from within a few miles of the Tarrant County line, but we also serve Haslet, TX, North Richland Hills, TX, Roanoke, TX, and Southlake, TX. Dispatch is coordinated from the brand’s Dallas-Fort Worth office, and crews serve Keller locally.
Serving Keller, TX – Our Local Coverage Area
We’re based in the Keller area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Keller
Most Keller gate repairs are scheduled within the same week, and true emergencies – a gate stuck open or a motor that won’t stop – can often get a same-day visit. Call (469) 530-2485 and we’ll tell you the next available window while you’re on the phone.
Many Keller HOAs require architectural review before a new gate goes in. We provide the spec sheet and design details your committee needs. The review timeline is usually your HOA’s process, but we’re familiar with the paperwork common in Keller neighborhoods.
Repair fixes the part that failed – a hinge, a weld, a limit switch, a control board. Replacement means the operator is beyond economic repair and a new motor goes in. We only recommend replacement when the old unit has failed in a way that won’t hold up. Call (469) 530-2485 for an exact quote on either path – estimates are free.
For gate repair in Keller, TX, call (469) 530-2485. We listen to what the gate is doing, give you a written price, and stand behind the work for a full year.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Keller Customers Say
"Keypad and remotes set up fresh for the whole neighborhood. Done cleanly and quickly."
- Chris W."Straight answers on whether to repair or replace the operator. Repair was the right call."
- Wanda F."Gate hinge was bending under the weight. Welded a new bracket on and re-hung it. Solid now."
- Rudy A.