Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Kenmore, WA
Gate repair in Kenmore comes with a specific set of challenges: hillside lots, older driveway gates along the Sammamish River corridor, and wet winters that test every hinge, sensor, and circuit board. Carver Gate Repair handles all of it, from a swing gate off NE 175th Street to a slide gate at the top of a gravel drive near Arrowhead. We’re the gate company that gives you a written price before any work starts and a full-year guarantee on every repair. If your gate won’t open or won’t close, call (469) 530-2485 and a live person answers, day or night.
Why Kenmore Homes Are Different
Kenmore sits at the north end of Lake Washington where the terrain rolls from the waterfront up into steeper residential streets. That grade change matters for gate work. A swing gate on a slope carries more load on the lower hinge, so we set posts deeper and check the bracket bolts more carefully than a flat-lot install would require. Homes near Log Boom Park and along the Burke-Gilman Trail corridor tend to have older gates, often 15 to 20 years old, with motors that have been patched rather than properly repaired.
The climate does the rest. Seven months of rain means moisture gets into control boards, limit switches, and photo eyes that would stay dry in eastern Washington. Rust forms on chain drives, and expansion and contraction of concrete pads shifts gate posts a quarter-inch a year until the gate starts dragging. We see it on the hillside streets north of SR 522 and in the neighborhoods off 68th Avenue NE. Kenmore’s mix of 1970s ramblers and newer construction means some gate systems are older than the homeowners running them. We explain what’s there, what it needs, and what it costs before we touch a thing.
Our Main Kenmore Services
Most calls we take in Kenmore start with a gate that won’t move or a motor that quit, and both are covered by dedicated service pages below.
Gate Repair in Kenmore
Gate Repair in Kenmore covers the mechanical and electrical failures that stop a gate from doing its job: bent hinges, sagging frames, broken wheels, damaged tracks, and sensor faults. Kenmore’s wet winters accelerate corrosion on steel hardware, so we check the entire assembly, not just the part that failed. Every repair gets a written guarantee good for a full year, and the price is agreed before work begins.
Gate Installation in Kenmore
Gate Installation in Kenmore handles new gate systems from the first site measure to final programming. On a sloped Kenmore lot, that starts with grading and post depth assumptions that don’t apply in flat neighborhoods. We size the operator for the gate’s actual weight and use, run the power correctly, and set safety edges and photo eyes where they belong. You get a written price before the job starts, and it doesn’t change at the door.
Gate Motor Repair in Kenmore
Gate Motor Repair in Kenmore is for operators that hum without moving, open but won’t close, or trip the breaker when they try. We work on nine brands, including Linear, Viking, and DoorKing, so the right parts come the first time. Moisture and power surges from winter storms are common culprits here, and we diagnose the board, limit switch, and capacitor rather than guessing. The repair is quoted upfront and covered by the same 365-day written guarantee as everything else we do.
What happens when you call
- 1
A real person answersNo phone trees – you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Kenmore
Our technicians work on Linear, Viking, DoorKing, and Ghost Controls systems, plus five other major motor brands. We keep common boards, limit switches, and remote receivers stocked locally so most Kenmore repairs don’t wait on parts. If you’re not sure what’s on your gate, our brands page explains what we cover and how to identify your operator.
Pricing for Gate Company in Kenmore, WA
| Service | Typical range in Kenmore |
|---|---|
| Gate repair service call | $75 – $125 |
| Hinge replacement (pair) | $180 – $340 |
| Gate wheel or roller replacement | $120 – $240 |
| Sensor or photo eye replacement | $150 – $300 |
| Keypad installation | $200 – $380 |
| Limit switch replacement | $160 – $320 |
| Gate motor replacement | $650 – $1,400 |
| Full gate installation | $2,800 – $7,500 |
What pushes Kenmore prices toward the top of those ranges is usually slope. A gate on a 10-degree grade needs stronger brackets, longer post work, and more precise alignment, and that takes more labor. The price we give you is written, it includes everything, and it does not change when we start the job.
Neighborhoods We Serve in Kenmore
We take calls across all of Kenmore, from the waterfront streets near Log Boom Park to the hillside homes above 68th Avenue NE. Our dispatch covers the whole city with no zone-based surcharge.
- Arrowhead
- Moorlands
- Uplake
- Kenmore Hills
- Log Boom Park area
Most Kenmore calls get a same-day or next-day visit depending on when you phone, and emergency calls are answered by a live person 24/7.
Service Area – Cities Near Kenmore
Carver Gate Repair works throughout the north Lake Washington and south Snohomish corridors. If you’re just over the city line, we also cover Bothell, WA, Mountlake Terrace, WA, Lynnwood, WA, and Woodinville, WA. Dispatch and scheduling are coordinated from our Seattle office, and crews serve Kenmore locally.
Serving Kenmore, WA – Our Local Coverage Area
We’re based in the Kenmore area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Kenmore
Most non-emergency calls in Kenmore are scheduled for the next business day. Emergency calls are answered by a live person around the clock, including weekends and holidays. Call (469) 530-2485 and we’ll give you a straight arrival window.
For most repairs, no permit is required in Kenmore. On new installations, we handle the technical drawings and specifications your HOA or the city may ask for, and we’ll tell you upfront if a permit looks likely. The price covers everything we do.
We cover the entire city: Arrowhead, Moorlands, Uplake, Kenmore Hills, everything from the lakefront to the north city limits. There’s no zone-based service charge and we’ll tell you the written price before we send a technician. Call (469) 530-2485 for a free estimate.
If your Kenmore gate needs repair, a new motor, or a full replacement, call Carver Gate Repair at (469) 530-2485. You’ll speak to a live person, get a written price before any work starts, and every repair is backed in writing for a full year.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Kenmore Customers Say
"Straight answers on whether to repair or replace the operator. Repair was the right call."
- Wanda F."Gate hinge was bending under the weight. Welded a new bracket on and re-hung it. Solid now."
- Rudy A."Slide gate wasn't opening fully. Veteran tech found a worn drive chain and a misaligned limit. Fixed both in one visit."
- Don H.