Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Maltby, WA
Maltby sits on the Snohomish County side of the King County line, a mix of older ranch homes, newer acreage properties, and equestrian parcels where driveways tend to be long and gates tend to be load-bearing daily equipment rather than decorative extras. Gate work in Maltby means dealing with wet, heavy soil that shifts posts seasonally, and with timber that swells through the winter. We handle repair, installation, and motor work across Maltby, and every job starts with a written price before any work begins. Call (469) 530-2485 and a live person answers, any hour.
Why Maltby Homes Are Different
Maltby properties run larger than the suburban average. Many homes sit on half-acre to multi-acre lots along Paradise Lake Road, 212th Street SE, and the winding stretches off Yew Way, which means longer gate spans and heavier leafs than you find in a typical planned subdivision. A 16-foot steel tube gate on a concrete post and a 10-foot cedar gate on a wood post fail differently, and the fix that works for one is wrong for the other. We see that distinction every week in Maltby.
The soil matters too. Maltby’s glacial till drains slowly, and in a wet winter the ground around gate posts can heave enough to throw a gate out of plumb by a quarter inch or more. That quarter inch is the difference between a gate that latches and one that drags across the driveway. When we set posts in Maltby we account for the drainage pattern and the frost line, not just the width of the opening.
Snow is rare but ice is not. Cold snaps in the valley freeze the fine moisture inside gate motor housings and on limit switch contacts, which is why we see a spike in motor no-starts in late December and January. Most Maltby gates are not enclosed or heated, so the equipment has to be sealed and adjusted to tolerate the damp.
Our Main Maltby Services
Two jobs dominate the call volume in Maltby: gates that have fallen out of alignment or stopped latching, and motors that stopped responding to remotes or keypads. Each has its own Maltby page with the full breakdown.
Gate Repair in Maltby
A sagging gate in Maltby usually traces back to a hinge pulling loose from a damp post, or a post that has moved with the soil. We inspect the hinge plates, the post set, the latch alignment, and the track or roller condition, then write up the repair with a fixed price before we touch a wrench. The full year guarantee on every repair is in writing. Full details are on our Gate Repair in Maltby page.
Gate Installation in Maltby
New gate installations in Maltby almost always involve a custom width, since driveway openings here are rarely standard. We measure the span, check the soil at each post location, and spec the gate and hardware to the actual conditions, including the slope if the driveway has one. Written price before any work starts, and the installation is scheduled, not rushed. See Gate Installation in Maltby for the process and options.
Gate Motor Repair in Maltby
When a Maltby gate motor runs but the gate won’t move, or the remote stopped working overnight, the cause is often a limit switch, a capacitor, or a board damaged by moisture. We carry parts for the major brands and diagnose on site rather than guessing over the phone. Same-day service is available for motor failures. The breakdown and the repair scope are covered on the Gate Motor Repair in Maltby page.
What happens when you call
- 1
A real person answersNo phone trees – you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Maltby
We work on Viking, Ghost Controls, DoorKing, and Elite systems in Maltby, among others. Common replacement boards, limit switches, and remote receivers for these brands are stocked on our trucks, which shortens turnaround on most motor repairs. See our brands for the full list and what each system typically needs.
Pricing for Gate Company in Maltby, WA
| Service | Typical range in Maltby |
|---|---|
| Gate realignment and latch adjustment | $140 – $300 |
| Hinge replacement (welded or bolted) | $85 – $220 per hinge |
| Gate post reset or replacement | $250 – $700 per post |
| Warped or sagging gate frame repair | $180 – $400 |
| Gate opener circuit board replacement | $150 – $450 |
| Limit switch or remote receiver repair | $90 – $220 |
| Full gate motor replacement | $450 – $1,300 |
| New gate installation (labor only) | $800 – $3,500 |
| Welding repair on steel or aluminum gate | $70 – $200 per repair point |
What pushes a Maltby quote toward the top of these ranges is the same thing that makes the work different here: a heavy gate on a long span, posts set in wet soil that need deeper footings, or motor damage from moisture that requires replacing more than one component. Whatever the number is, you will see it in writing before the work starts, and that number is the number you pay.
Neighborhoods We Serve in Maltby
We run calls across Maltby regularly. The neighborhoods below represent the spread of the area, and the response note applies to all of them.
- Paradise Lake Road corridor
- Yew Way and the western acreage parcels
- 212th Street SE corridor
- Clearview border area along Highway 9
- East Maltby toward the Snohomish River valley
Most Maltby repair calls are reached within the same day, and emergency gate-down calls are dispatched as they come in, including nights and weekends.
Service Area – Cities Near Maltby
Maltby is our home base for this area, and the same crews and same written-price standard extend to nearby cities. We also cover Seattle, WA, Spokane, WA, Tacoma, WA, and Vancouver, WA with the same guarantee on every repair.
Serving Maltby, WA – Our Local Coverage Area
We’re based in the Maltby area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Maltby
Most Maltby calls are reached the same day. A gate that won’t close or won’t open and is blocking a vehicle gets priority, and we dispatch emergency calls around the clock, including weekends. Call (469) 530-2485 and a live person answers.
Most repair and replacement work on an existing gate line does not require a permit, but a new gate with a new driveway cut or a large masonry column can trigger county review. We’ll tell you during the estimate if your job falls into that category, and we coordinate the paperwork when it does.
No. The written price you approve before work starts is the final price. If we open the gate and find something additional, we stop, show you what we found, and get approval on a new written price before continuing. Nobody works an open tab on a Maltby job.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Maltby Customers Say
"Showed up a little after the window, but he called ahead. On time otherwise, polite, and efficient. Cleaned up all the tools."
- Joan K."Swing gate arm snapped. They replaced the actuator and tested the safety reverse. Fair price."
- Angela P."Keypad and remotes set up fresh for the whole neighborhood. Done cleanly and quickly."
- Chris W.