Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Parkwood, WA
Carver Gate Repair is the gate company Parkwood homeowners call when a driveway gate stops opening, a motor burns out, or an old swing gate needs to be replaced outright. Parkwood is a compact Pierce County community where homes sit on streets that see steady rain, occasional frost, and marine air from the Sound, all of which take a toll on steel, hinges, and circuit boards. If your gate is down, call us at (469) 530-2485. We show up, give you a written price, and get the gate working.
Why Parkwood Homes Are Different
Parkwood’s housing stock runs heavily to mid-century and 1970s ramblers on level, grass-heavy lots, with driveways that are wide enough for two cars and a gate set on piers. That means most gate work here is repair and retrofit, not new construction. Steel posts set decades ago have worked loose in wet, heavy soil. Hinges that lasted through dry summers seize up after consecutive gray winters. Gate motors exposed to Pierce County moisture corrode faster at the limit switch and control board than they would inland. And because Parkwood sits near the top of the Kitsap Peninsula’s southern edge, salt air from the Sound accelerates surface rust on exposed gate frames, especially on the side facing prevailing wind.
We also see a lot of swing gates here, not just sliding ones. A swing gate on a Parkwood lot usually has a piston-style operator mounted at the hinge post, and when that operator’s internal seals fail, the gate groans at the midpoint and stalls. On the slide-gate side, debris from alder and maple trees collects in the track, so we recommend a track-clearing habit every few months during leaf fall. Every Parkwood job starts with us looking at the surface the gate was mounted on, not just the gate itself.
Our Main Parkwood Services
Most calls we take in Parkwood fall into two buckets: a gate that has stopped working, and a motor that has burned out on a gate that is otherwise fine. All three of our core services have their own dedicated Parkwood page linked below.
Gate Repair in Parkwood
When a gate in Parkwood starts binding, sagging, or refusing to close fully, the fix usually comes down to hardware that has shifted over time. We re-set posts, replace bent hinges, rebuild latch assemblies, and get the gate swinging or sliding square again. Rain is the quiet saboteur here: it swells the ground around posts and speeds up rust on every moving part. See Gate Repair in Parkwood for pricing and what a typical repair visit covers.
Gate Installation in Parkwood
New gate work in Parkwood means taking a site that has probably never had a gate and deciding what post depth, hinge type, and panel weight the soil and driveway width will support. We handle measured, custom-fit installations from the first site check to the final adjustment. Most fences and driveways here sit on flat ground, which simplifies a swing-gate install, but wet ground means posts have to go deeper than code minimums to resist frost heave. See Gate Installation in Parkwood for the full scope and pricing.
Gate Motor Repair in Parkwood
If the gate itself is fine but nothing moves when you hit the remote or keypad, the problem is in the operator. We work on Viking, Ghost Controls, DoorKing, and Elite motors, among others, replacing limit switches, loop detectors, control boards, and worn gears. Moisture intrusion is the leading cause of motor failure in Parkwood: condensation gets into the housing and sits on the board. See Gate Motor Repair in Parkwood for cost ranges and turnaround.
What happens when you call
- 1
A real person answersNo phone trees – you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Parkwood
Our technicians service Viking, Ghost Controls, DoorKing, and Elite equipment, with parts stocked for common failures like limit switches, loops, and receiver boards. See our brands for the full list of manufacturers we support.
Pricing for Gate Company in Parkwood, WA
| Service | Typical range in Parkwood |
|---|---|
| Gate repair, small hardware | $180 – $340 |
| Gate repair, hinge or post reset | $350 – $700 |
| Gate motor repair | $250 – $550 |
| Gate motor replacement | $750 – $1,400 |
| Swing gate operator install | $1,200 – $2,200 |
| Slide gate operator install | $1,500 – $2,800 |
| Full gate installation | $2,500 – $6,500 |
| Loop detector replacement | $300 – $600 |
| Limit switch replacement | $150 – $350 |
What pushes a Parkwood job toward the top of any range is usually the condition of the existing post: if the post has rotted or tilted, we are resetting it before we hang a gate or mount a motor, and that adds labor. Pricing is always written down and agreed before work starts, and it does not change once the job is open.
Neighborhoods We Serve in Parkwood
We cover the whole Parkwood area, including the streets off 146th and 152nd, the blocks east of Peacock Hill, and the communities that back up to Curley Creek. Response is typically same-day or next-day for gate repair calls.
- Peacock Hill
- East Parkwood
- North Parkwood
- Curley Creek
- West Parkwood
Service Area – Cities Near Parkwood
In addition to Parkwood, we serve gate repair and gate motor work throughout the region. Our crews cover Seattle, WA, Spokane, WA, Tacoma, WA, and Vancouver, WA. Dispatch and scheduling are coordinated from our Seattle office; crews are dispatched locally for Parkwood jobs.
Serving Parkwood, WA – Our Local Coverage Area
We’re based in the Parkwood area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Parkwood
Most gate repair calls in Parkwood are scheduled same-day if you call before mid-afternoon. Motor diagnostics are typically next-day. Call (469) 530-2485 and a live person answers, 24/7, including weekends.
Basic gate repair and motor replacement generally do not require a permit. New gate installation or post work may trigger Pierce County requirements depending on height and location. We can check before we start and we will not do work that needs a permit without one.
Every repair carries a written guarantee good for a full year from the date of service. If the same failure comes back within that window, the second visit is free. The guarantee is in writing, not verbal, because a gate repair should survive a Parkwood winter.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Parkwood Customers Say
"Good repair on a motor board. Waited a few days on the part, but they stayed in contact."
- Shelby T."Showed up a little after the window, but he called ahead. On time otherwise, polite, and efficient. Cleaned up all the tools."
- Joan K."Swing gate arm snapped. They replaced the actuator and tested the safety reverse. Fair price."
- Angela P.