Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor Repair Across Irving
Gate motor repair in Irving typically runs $185 to $640 depending on whether the failure is a control board, a stripped drive gear, a dead capacitor, or a complete operator replacement. Most jobs are completed in a single visit, and every repair includes a written price before any work starts. Our Gate Motor Repair team covers every corner of Irving, from the winding streets of Valley Ranch to the commercial drives along MacArthur Boulevard. When an operator stops mid-cycle or refuses to open at all, call (469) 530-2485 and a live person answers, not a voicemail queue.
Why Carver Gate Repair Is Irving’s Preferred Gate Motor Repair Company
Irving homeowners call us because the process is predictable from the first phone call to the final test cycle. We assign a background-checked, uniformed technician to every job, and that technician arrives with a written quote already mapped to the symptoms you described. The number on that quote is the number you pay unless we find something hidden inside the operator that makes additional work necessary, and in that case we stop and get your approval before turning another screw.
We don’t operate as a generalist contractor that happens to take gate calls between kitchen remodels. Gate operators are what we do, across nine brands including FAAC, BFT, Linear, and Viking. When a homeowner near L.B. Houston Park has a swing gate that stalls halfway and a commercial property manager near Las Colinas has a slide operator throwing a fault code, both calls go to the same Irving dispatch line. The repairs are different. The process is the same, and that consistency is why we get repeat calls from the same households and the same property managers year after year.
Part of the Garrison Partners family, Carver Gate Repair has operated to The Garrison Standard since 2008. Every repair carries a written 365-Day Done Right Promise. If the repair fails within that year, we return and fix it again at no charge. That guarantee is on every invoice, in plain language, with no fine print to squint at.
Gate Keypad in Irving
Gate keypad installation and repair in Irving is a common call for front entries and side-yard pedestrian gates where a remote isn’t practical. A new keypad wired to an existing operator typically runs $145 to $320 in Irving, including the keypad, wiring to the control board, programming, and testing. Weatherproofing matters here because Irving catches hard summer thunderstorms and the occasional winter ice event, and a poorly sealed keypad corrodes from the inside out within two seasons.
Adding or Replacing a Keypad on an Existing Operator
The first step is confirming the operator’s control board supports remote keypad input, which nearly all LiftMaster, FAAC, and Linear boards do. We wire the keypad to the board, program entry codes, set the relay timing to match your operator’s cycle, and test the gate under real use. Homeowners in University Hills and the older neighborhoods east of Loop 12 often ask about wireless keypads, which eliminate the need to trench wire across a walkway.
Keypad Failure Patterns in Irving
We see three failures regularly in Irving. Sun-baked keypads near gate posts that get full afternoon exposure crack and let moisture into the contacts. Hard water from Irving’s municipal supply leaves mineral residue on rubber button membranes. And doors that are keypad-only with no remote backup strand homeowners when the keypad dies, which is why we recommend programming at least one extra code and keeping a remote in the house.
Gate Closer Spring in Irving
Gate closer spring repair and replacement in Irving runs $95 to $260 for most residential single-gate applications. The spring that pulls a gate shut after someone walks through wears out or snaps, and the gate either slams shut or drifts open and stays there. In Irving’s older single-family neighborhoods like Hospital District and South Irving, many homes have had the same gate hardware for two decades, and the closer spring is usually the first component to fail.
Replacement Springs and Tension Adjustment
A gate closer spring is not a part to guess at. We match the replacement spring to the gate’s weight, length, and hinge geometry, then set the tension so the gate closes firmly but doesn’t slam. On wood gates especially, the wrong tension splits the hinge-side stile over time. We also check the end caps and mounting brackets while the spring is off, because a worn bracket will tear through a new spring in months.
Signs a Closer Spring Needs Attention in Irving
If a gate that used to close itself now needs a push, the spring has lost tension or snapped entirely. If it slams hard enough to rattle the latch, the tension is over-set. Either way, the fix is usually a single visit. This is one repair where the cost should not come as a surprise, and our written quote before any work starts keeps it that way.
Trusted Brands We Service in Irving
We carry parts and maintain factory training on the operators most common in Irving, including FAAC swing operators on wood gates in older neighborhoods, BFT slide operators on Las Colinas commercial drives, and Linear and Viking units on mid-size single-family gates throughout Valley Ranch and Hackberry Creek. Matching the part to the operator already installed is not optional. A FAAC board will not drive a Linear motor, and a Viking capacitor is not rated for a BFT controller. We stock common boards, capacitors, gear sets, and photocell kits locally for fast turnaround on Irving calls, so a repair does not wait on a parts truck from out of state.
Common Gate Motor Repair Problems We See in Irving Homes
- Hinge posts shifting in expansive clay. This is the recurring problem we see across Irving’s mid-century housing stock. North Texas clay swells and shrinks with seasonal moisture, and a gate post set without proper depth moves enough to throw off operator arm geometry. The motor gets blamed for stalling when the real issue is three inches of post movement.
- Slide gate operators tripping on entrapment protection. Commercial and higher-end residential slide gates in Las Colinas and Valley Ranch run loop detectors and photocells that go out of alignment from heat, vibration, or vehicle strikes. The operator faults and refuses to move, which looks like a failed motor but is often just a sensor misaligned by half an inch.
- Dead backup batteries on aging operators. Many Irving single-family homes have LiftMaster or FAAC operators that are ten to fifteen years old. The control board still works, but the backup battery died years ago, so the gate runs on AC power only. When a storm knocks out power, the gate won’t open at all, and the homeowner reads that as a motor failure.
- Keypad corrosion from Irving’s weather swings. Sun-baked keypads crack open, then a single heavy rain fills the housing. The keypad stops accepting codes, and the operator ignores the input. The motor may be perfectly fine, but the gate won’t respond from the street side.
Pricing for Gate Motor Repair in Irving, TX
A straightforward repair, like a capacitor or a photocell alignment, runs $185 to $275 in Irving. A control board replacement on a LiftMaster or FAAC operator runs $300 to $520. A full operator replacement, including the motor, arm, and control system, starts at $640 and goes up based on gate size, length of the run, and whether the old mounting points need rework. On commercial slide gates along the Las Colinas corridor, repairs frequently involve the rack, the drive chain, or the loop detector, and those jobs run $350 to $1,200 depending on the damage. Every job gets a written price before any work starts. Call (469) 530-2485 for a free estimate, and the number we quote is the number we stand behind.
We Also Serve Cities Near Irving
Our Irving team also handles gate motor repair for homeowners in Dallas, Balch Springs, Hutchins, and Mesquite. If you’re just outside the Irving city limits or live in one of the adjacent unincorporated pockets, Gate Motor Repair in Irving coverage still applies to your driveway. We dispatch from our Dallas-Fort Worth office, and the same Garrison Standard applies on every job regardless of which side of the city line the gate sits on.
Serving Irving, TX – Our Local Coverage Area
We’re based in the Irving area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Motor Repair in Irving
Usually not. In Irving residential gates, a stall halfway through travel often means the hinge post has shifted in the expansive clay soil, which throws the operator arm geometry out of line and makes the motor work against the gate’s own weight. The motor may be perfectly healthy and still stall because it is fighting a post that moved. We diagnose the cause before quoting a replacement.
No. Slide gate operators mount on a steel pad or post beside the driveway, not under it. Repairs to the motor, gearbox, chain, or rack are done from the side, so your driveway stays intact. The only digging involved is if we need to reset a loop detector, and even that is a narrow saw cut and a fresh seal in the pavement, not a full dig.
We service and repair nine brands, including FAAC, BFT, Linear, Viking, LiftMaster, Ghost Controls, DoorKing, Elite, and Mighty Mule. Parts for the most common failures on these brands, control boards, capacitors, gear sets, and photocells, are stocked locally for Irving calls. That means most repairs are completed in one visit, not two.
Yes. A functioning gate operator in Irving must have working entrapment protection, typically a photocell beam and a reversing mechanism, in line with UL 325 safety standards. If the photocell is out of alignment or the reverse test fails, the gate should be locked out of automatic operation until it is corrected. We test every repair against these standards before we call the job done, and the written guarantee covers this work for a full year.
Yes, and we do it regularly on gates throughout Irving. A weatherproof keypad can be wired to most existing LiftMaster, FAAC, BFT, or Linear control boards, with programming and testing included. The job runs $145 to $320 on most residential gates. Call (469) 530-2485 for an exact quote, and the estimate is free.
Local Conditions That Shape Gate Work in Irving
Irving’s gate work is split between mid-century single-family pockets and the high-density Las Colinas and Valley Ranch corridor, so the same city produces two very different jobs. A wood swing gate in the Hospital District fights North Texas shrink-swell clay for its post footing, and a commercial slide gate along MacArthur runs a loop detector on a shared driveway. That means motor sizing, operator duty rating, and entrapment protection have to be judged per driveway, not per city. A homeowner near Irving Boulevard needs a different operator than a property manager off Royal Lane, and treating them the same is how gates get damaged and operators get replaced in the dark.
We were called to a home near Running Bear Road in Valley Ranch where a LiftMaster swing gate opener had been stalling halfway through travel. The panel had been re-hung by someone else, but the hinge post was moving in the clay and the operator arm was fighting it. Our tech dug back to the post footing, corrected the sag at the source, re-set the operator arm geometry, then re-tested the safety photocell and reversal before we buttoned it up. The gate has cycled clean since. That is the difference between replacing a part and fixing the failure.
Call Carver Gate Repair for Gate Motor Service in Irving
If your gate motor is stalling, refusing to open, or throwing fault codes, call (469) 530-2485. A live person answers, schedules a background-checked technician, and gives you a written price before any work starts. Every repair is covered by the 365-Day Done Right Promise, with a free second visit if the repair fails within the year. That is the Garrison Standard, and it is the same standard on every gate in every Irving neighborhood, from Valley Ranch to South Irving.
Written by Lonnie Burke, Owner at Carver Gate Repair, serving Irving since 2008.