Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Cleburne, TX
Gate work in Cleburne runs into two conditions that shape almost every job: heavy clay soil that shifts with the seasons, and a housing stock split between older ranch-style homes and newer acreage properties. That combination means a gate that worked fine in March can be dragging or jammed by June, when the ground has dried and moved. Carver Gate Repair works on gates and gate motors across Cleburne five days a week, with a live person answering the phone at (469) 530-2485 whenever you call.
Why Cleburne Homes Are Different
Cleburne sits on expansive clay, and it moves. A gate post set in that soil can drift half an inch in a wet spring, which is enough to throw a cantilever gate off its track or make a swing gate latch refuse to catch. Homeowners on the west side of town, out toward the Nolan River and the neighborhoods around Lake Pat Cleburne, deal with it most. Those properties tend to have wider driveways and heavier gates, so the operators work harder and limit switches fail sooner than they would on a flat suburban lot in Fort Worth.
The older neighborhoods closer to downtown, including the streets around Hulen Park and the historic district, have tighter setbacks and a lot of gates installed decades ago. Pipe-frame swing gates on buried posts are common there. When the hinges wear or the post leans, the gate doesn’t just sag, it starts scraping the driveway or hanging on the latch post. Fixing that properly usually means resetting the post in concrete, not just adjusting the hinge. Newer construction in the subdivisions along Nolan River Road and Country Club Road tends toward ornamental steel and opener systems on both ends of the house, which brings its own load of wiring, sensors, and weather sealing.
Cleburne is also a full four-season climate. Summer heat bakes the powder coat and shortens the life of plastic gear components inside swing and slide operators. Spring storms bring wind gusts that slam unlatched gates and rip stops off their mounts. Winter freezes are short but they catch exposed control boards and keypads. Any honest assessment of gate work here starts with the soil and the weather, because both of them work against the equipment.
Our Main Cleburne Services
Most calls we take from Cleburne fall into two buckets: a gate that has stopped working, and a gate motor that quit. The three pages below cover each in detail for Cleburne, including local pricing and what a typical job looks like.
Gate Repair in Cleburne
Gate repair in Cleburne usually means one of three things: a swing gate that has sagged off its hinges, a slide gate that has jumped its track, or a latch and post alignment that no longer meets. Clay soil is behind most of it. We check the post footing before we touch the hinges, because adjusting a hinge on a moving post buys you about six months. If the post is sound, we repair and reinforce. If it has moved, we reset it. Every Cleburne repair gets a written price before we start and a written guarantee good for a full year. Full scope and cost breakdown: Gate Repair in Cleburne.
Gate Installation in Cleburne
A new gate in Cleburne has to be built for the soil it sits in and the wind it will catch. We measure the opening, check the grade, and size the posts and footings for the gate’s weight and the clay’s movement, not just the width of the driveway. Homeowners in the newer subdivisions off Nolan River Road often want a matching double-swing with an operator on each leaf. On acreage lots outside town, the call is more often a heavy slide gate with a solar operator and a keypad. Both start the same way: a free site measure and a written price. Details and pricing: Gate Installation in Cleburne.
Gate Motor Repair in Cleburne
When a gate motor stops responding in Cleburne, the cause is usually one of three things: a limit switch that has drifted, a control board that has failed after a storm or a heat spike, or a capacitor that gave out. We carry parts for the major brands, including Linear, Viking, Ghost Controls, and DoorKing, so the diagnosis and the fix can often happen on the same visit. The motor gets tested under load before we leave, opening and closing the gate several times, not just once. See what we check and what it costs: Gate Motor Repair in Cleburne.
What happens when you call
- 1
A real person answersNo phone trees – you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Cleburne
We work on gate motors from Linear, Viking, Ghost Controls, and DoorKing, along with the rest of the major brands on our brands page. Stock of common limit switches, capacitors, control boards, and remotes rides on our service vehicles, which shortens turnaround time on most Cleburne calls to a single visit.
Pricing for Gate Company in Cleburne, TX
| Service | Typical range in Cleburne |
|---|---|
| Gate repair, minor (hinge adjust, latch realign, stop replacement) | $95 – $250 |
| Gate repair, moderate (post reset, track realign, weld repair) | $250 – $600 |
| Gate repair, major (post replacement, frame rebuild) | $600 – $1,400 |
| Gate motor replacement (standard swing or slide operator) | $850 – $1,900 |
| Gate motor repair (limit switch, capacitor, control board) | $180 – $525 |
| Gate installation, single swing (standard steel) | $1,600 – $3,800 |
| Gate installation, double swing | $3,800 – $8,500 |
| Gate installation, slide gate | $4,200 – $9,500 |
| Keypad or intercom install | $350 – $900 |
| Loop detector install or replacement | $400 – $950 |
What pushes a Cleburne quote toward the top of those ranges is usually footing work in shifting clay, a long power run to the gate, or a heavy ornamental gate that needs a larger operator. Whatever the number, it is written down and agreed to before we open a toolbox. That price does not change at the door.
Neighborhoods We Serve in Cleburne
We cover the full city of Cleburne and the acreage roads around it, including the following areas:
- Downtown and the historic district
- Neighborhoods around Hulen Park
- Country Club Road and the surrounding subdivisions
- Nolan River Road corridor
- Acreage properties around Lake Pat Cleburne
Most Cleburne calls are reached the same day they come in. The acreage lots on the outer edges of the city take a little longer, because the drive is real, but the response time is still measured in hours, not days.
Service Area – Cities Near Cleburne
Carver Gate Repair works in Cleburne and in the cities around it. Homeowners in Keene, TX, Joshua, TX, Alvarado, TX, and Burleson, TX call the same number and get the same written-price, written-guarantee standard. Dispatch and scheduling are coordinated from our Dallas-Fort Worth office; the crews that work gates in Cleburne live and work in the area.
Serving Cleburne, TX – Our Local Coverage Area
We’re based in the Cleburne area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Cleburne
Most Cleburne repair calls are reached the same day. Calls that come in before noon are typically scheduled for that afternoon; calls after noon go on the next morning’s board. If the gate is stuck open or won’t close and security is the concern, tell the person on the phone and we’ll treat it as a priority. Call (469) 530-2485 and a person answers, day or night.
It depends on the scope. A direct replacement of an existing gate on the same posts rarely requires anything. A new gate with new footings or a new operator with electrical work can trigger permit requirements in some parts of Cleburne, particularly in the historic district. We can tell you what applies to your address before any work is scheduled.
Yes. Several Cleburne subdivisions have design standards for gates, including height limits, finish colors, and operator placement. We work to those specs and can provide the documentation the HOA asks for. If you have the HOA’s gate standards, have them ready when we come out and we’ll make sure the quote matches before you spend anything.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Cleburne Customers Say
"Swing gate arm snapped. They replaced the actuator and tested the safety reverse. Fair price."
- Angela P."Keypad and remotes set up fresh for the whole neighborhood. Done cleanly and quickly."
- Chris W."Straight answers on whether to repair or replace the operator. Repair was the right call."
- Wanda F.