Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Parker, TX
When a gate fails in Parker, it tends to fail at the worst moment: a cold snap following a wet week, or the first day a homeowner plans to leave town. Carver Gate Repair handles gate repair, gate installation, and gate motor repair across Parker, TX, with crews that arrive in marked vehicles, in uniform, carrying a written price before any work begins. We work on nine gate-motor brands, so the technician who shows up already knows the system sitting on your property. Schedule a visit by calling (469) 530-2485.
Why Parker Homes Are Different
Parker sits in a part of Collin County where homes carry the kind of square footage and lot size that make a gate more than decoration. Long driveways, equestrian properties, and three-acre parcels are common here, which means gate operators see more cycles per day than a typical suburban gate. The soil in this area, largely clay-heavy, expands and contracts with rain and drought. That movement translates into gate posts that shift a half-inch over a season and operators that bind against misaligned tracks.
Homeowners in Parker also deal with HOA covenants more often than not. Several subdivisions have architectural review requirements for any visible gate or motor change, which means the job is not just mechanical: it runs through an approvals process first. We have worked on enough Parker properties to know which questions to ask before ordering an operator, so a homeowner is not left with a boxed LiftMaster and a board meeting after the fact. The climate matters, too. Summer heat above 100 degrees thins the grease in older swing arms, and our techs see more limit switch drift in August than any other month.
Our Main Parker Services
The three calls we take most from Parker homeowners concern a gate that will not open, a gate that needs to be replaced entirely, and the motor that drives it. Each service has its own Parker page with pricing and a fuller explanation of the work.
Gate Repair in Parker
Parker gates fail in predictable ways: a break in the weld at the hinge, a chain that jumps the sprocket, a wheel that has ground flat against its track. Our repair calls start with a diagnosis, not a blind guess. The technician checks the physical gate first, then the operator, because a binding post can destroy a motor, and a motor can hide a post problem. We quote a written price before work starts. No number moves once the job is open. Full details on Gate Repair in Parker.
Gate Installation in Parker
A new gate in Parker usually means a heavier gate than the one it replaces, and that changes the engineering. The operator has to match the leaf weight, not just the look. We measure, check the column depth and footing, and specify the system before any concrete is poured. Powder-coated steel and ornamental aluminum are both common in this area, and each acts differently in wind and heat. See Gate Installation in Parker for what the process includes and what it costs.
Gate Motor Repair in Parker
Motor complaints in Parker run from a dead capacitor to a control board that failed after a power surge. A lightning strike to a property on a high point, of which Parker has a few, can smoke a board overnight. We diagnose the motor itself before recommending a repair or a replacement, and we stock boards, remotes, and limit switches for the brands most often installed in this area. The motor page walks through the difference between a repair and a full operator change: Gate Motor Repair in Parker.
What happens when you call
- 1
A real person answersNo phone trees – you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Parker
Our technicians are trained on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule equipment. We carry common repair parts for FAAC, BFT, Linear, and Viking systems in our service vehicles, which shortens turnaround on the majority of Parker jobs to a single visit.
Pricing for Gate Company in Parker, TX
| Service | Typical range in Parker |
|---|---|
| Gate diagnostic | $65 – $120 |
| Gate repair (minor) | $150 – $450 |
| Gate repair (major) | $450 – $1,800 |
| Gate installation (single swing) | $2,500 – $8,000 |
| Gate installation (double swing) | $4,500 – $14,000 |
| Gate installation (slide gate) | $5,000 – $16,000 |
| Gate motor repair | $180 – $500 |
| Gate motor replacement | $750 – $2,200 |
| Control board / receiver replacement | $220 – $600 |
| Keypad / remote programming | $80 – $180 |
What pushes a Parker job toward the top of a range is access: a gate set far back from the street on a long easement, or a fence line that blocks a service vehicle from getting close. A clay-heavy lot that has shifted a post also tends to add a half-hour of realignment before the gate itself can be addressed. Whatever the condition, the price is written down before any work starts, and it does not change at the door.
Neighborhoods We Serve in Parker
We work across Parker’s residential pockets, from larger estate lots to the smaller newer subdivisions off Parker Road. Response time in most of Parker runs the same day for urgent repair calls, and within a day or two for scheduled measurements and installations.
- Parker Landing
- Trails of Parker
- Spring Hollow
- Parker East
- Country Meadows
Service Area – Cities Near Parker
Carver Gate Repair handles Parker jobs directly, with dispatch coordinated from our Dallas-Fort Worth office. For homeowners we also serve in nearby markets, see our pages for Dallas, TX, Fort Worth, TX, Houston, TX, and San Antonio, FL.
Serving Parker, TX – Our Local Coverage Area
We’re based in the Parker area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Parker
These are the questions we answer most from Parker homeowners before any service call is scheduled. For specific pricing or service questions, call (469) 530-2485 and a live person answers, 24/7, weekends and holidays included.
Most Parker repair calls are handled the same day. A live person answers the phone around the clock, so the dispatcher can confirm an arrival window at the time of the call. Emergency calls, meaning a gate stuck open or a security gate that will not close, are prioritized.
Often yes. Several Parker subdivisions require architectural review for visible gate and motor changes. Our better move is to ask about your specific HOA before quoting, so any approval timelines are built into the schedule rather than discovered at the end. Call (469) 530-2485 and we will walk through it.
Every repair carries a written guarantee good for one full year from the date of service. If the same repair fails inside that window, Carver returns for a second visit at no charge. The guarantee is in writing, and it is not conditional on the weather, the traffic, or the age of the gate. For a free estimate, call (469) 530-2485.
If your gate will not open or close properly in Parker, call Carver Gate Repair at (469) 530-2485. We give you a written price before any work starts, and a live person answers the phone, day or night.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Parker Customers Say
"Swing gate arm snapped. They replaced the actuator and tested the safety reverse. Fair price."
- Angela P."Keypad and remotes set up fresh for the whole neighborhood. Done cleanly and quickly."
- Chris W."Straight answers on whether to repair or replace the operator. Repair was the right call."
- Wanda F.