Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in San Antonio?
Gate repair in San Antonio typically runs $185 to $650, with most homeowners paying between $280 and $420 for a standard residential fix. A simple hinge adjustment or limit switch reset sits at the low end, while motor replacement or structural welding on a wrought-iron driveway gate pushes toward the higher range. We see the full spread across San Antonio neighborhoods, from Alamo Heights to Helotes, and we quote every job in writing before touching a tool.
Gate Repair Cost Breakdown (2026)
These are the line-item ranges we’re quoting in the San Antonio market right now. Prices include labor and standard parts; specialty hardware or after-hours calls adjust from here.
| Repair Type | Typical Range |
|---|---|
| Hinge adjustment or replacement | $185 – $295 |
| Limit switch or loop detector repair | $220 – $340 |
| Articulating arm repair (swing gate) | $265 – $395 |
| Gate motor / operator repair | $295 – $485 |
| Full gate motor replacement | $650 – $1,450 |
| Wrought iron welding or structural repair | $340 – $620 |
| Track or roller replacement (sliding gate) | $280 – $450 |
| Control board or keypad replacement | $245 – $420 |
| Emergency / after-hours service call | $150 – $220 added to base |
What moves a job up or down? Access is the big one in San Antonio. A swing gate on a steep grade in Terrell Hills, where the operator fights gravity every cycle, wears parts faster and takes longer to dial in. Same for sliding gates in Stone Oak with heavy clay soil that shifts track alignment after every hard rain. We price for the actual condition we find, not a flat rate that hides surprises later.
What Affects Gate Repair Pricing in San Antonio
- Gate type and size. A 12-foot single swing with a Mighty Mule residential operator is a different job than a dual-swing commercial setup with a FAAC 770. More mass, more current draw, more precision in the limit settings.
- Motor brand and age. We stock parts and train on nine brands – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule – but a discontinued board or obsolete gear assembly can add a day for sourcing. Older DoorKing and Elite systems in Monte Vista and Olmos Park sometimes need this.
- Electrical run condition. San Antonio’s summer heat and occasional hard freezes degrade underground conduit. If we’re chasing a short between the house and the gate box, that diagnostic time shows in the final price.
- Structural vs. mechanical. A bent picket or loose weld on an iron gate is metalwork, not motor work. We have welders on crew, but it’s a different skill block with different rates than a technician swapping a control board.
- Access and terrain. Hill Country limestone, common in Shavano Park and Fair Oaks Ranch, makes post-setting and anchor work harder than flat loam. Steep drives complicate operator geometry. We don’t upcharge for terrain, but it affects how long the job takes and what hardware we spec.
- When you call. Standard rates cover business hours. After 6 p.m., weekends, and holidays, we still answer live and still dispatch, but the trip charge reflects the overtime. In San Antonio, we see most emergency calls during summer storm season when lightning takes out boards.
How to Save on Gate Repair
There’s no honest way to make gate repair cheap without cutting something that matters. These are the moves that actually protect your budget without sacrificing the fix.
- Get ahead of the noise. A grinding operator or sagging gate is telling you something. Catching it before the motor burns out or the post cracks saves the difference between a $280 adjustment and a $1,200 replacement. In San Antonio’s heat, operators work harder nine months a year – that wear shows up first as sound or hesitation.
- Know your system. If you can tell us the brand, model year, and symptoms when you call, we arrive with the right parts and the right technician. A Ghost Controls system in Alamo Ranch needs different spares than a Viking in The Dominion. One truck roll instead of two saves you a trip charge.
- Ask about bundled work. If you’ve got two gates or a motor acting up plus a hinge that’s been loose since last year, we’ll price it together. The second repair adds less labor than a separate call.
- Verify the guarantee terms. Our 365-Day Done Right Promise covers every repair for a full year, with a free second visit if anything fails inside that window. A cheaper quote with a 30-day verbal promise isn’t cheaper if you’re paying twice. The guarantee is in writing on every Carver job.
We don’t charge for estimates. Call (469) 530-2485 and we’ll give you a written price before any work starts.
FAQs – Gate Repair Cost
How much does a typical gate motor repair cost in San Antonio?
Most gate motor repairs in San Antonio run $295 to $485, including diagnostic, parts, and labor. That covers limit switch replacement, gear assembly work, control board repair, or loop detector troubleshooting on standard residential operators. If the motor is over 12 years old or has been repaired before, we may recommend replacement – we’ll put both options in writing so you can decide. Call (469) 530-2485 for a free estimate.
Is it cheaper to repair or replace a gate motor?
Repair is usually cheaper short-term if the motor is under 10 years old and the failure is isolated to one component – a $340 limit switch job versus $850 for a new operator. Replacement makes more sense when the motor has multiple failures, obsolete parts, or is operating near its weight limit on a heavy San Antonio iron gate. We quote both paths when it’s a close call, and we never push replacement for a simple fix. Call (469) 530-2485 to have a technician assess yours.
Can you fix my gate the same day I call?
We complete most San Antonio gate repairs same day or next day during business hours. We stock common parts for all nine brands we service – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule – and our technicians travel with a full parts loadout. After-hours and weekend calls depend on part availability, but we answer live 24/7 and dispatch when we can. Call (469) 530-2485 to check current availability.
Why do some gate repair quotes in San Antonio seem much lower than others?
A low quote often excludes the trip charge, diagnostic fee, or guarantee. We’ve seen competitors in the San Antonio market quote $150 for a “service call” that turns into $400 at the door, or offer a 30-day warranty against our full-year written guarantee. Our price is the full price, delivered in writing before work starts, with no movement at the door. The 365-Day Done Right Promise and free second visit are included, not extra. Call (469) 530-2485 for an upfront quote you can compare honestly.
Does Carver Gate Repair charge extra for homes in Hill Country or outside Loop 1604?
No – our standard service area covers San Antonio proper and the immediate Hill Country ring, including Boerne, Bulverde, and Fair Oaks Ranch, without zone surcharges. Travel time affects scheduling, not pricing. If you’re in a more distant outlying area, we’ll tell you upfront if any additional trip charge applies. Call (469) 530-2485 with your address and we’ll confirm.
How Carver Gate Repair Prices Every Job
- Diagnose on site. Our technician arrives in a marked vehicle, uniformed, and identifies the failure before quoting. No guesswork over the phone.
- Write the price. You get a single number on paper – parts, labor, and guarantee included. No line-item padding, no open-ended “plus materials.”
- Get your approval. Work starts only after you sign the written price. If you decline, you pay nothing for the diagnostic.
- Complete the repair. The technician tests every function – open, close, safety reverse, keypad, remote – before leaving.
- Leave the guarantee. The 365-Day Done Right Promise is printed on your invoice. If the same issue returns within a year, we come back free. No argument, no re-diagnostic charge.
That’s The Garrison Standard. We’ve operated to it since 2008, and every Carver location – including ours here in San Antonio – is held to the same code.
Get Your Written Gate Repair Estimate in San Antonio
We’re not the cheapest option in San Antonio, and we don’t try to be. We’re the option that shows up when promised, quotes in writing, and fixes it right the first time under a full-year guarantee. If your gate is sticking, grinding, or dead, call (469) 530-2485. A live person answers, 24 hours a day, and we’ll schedule your free estimate at a time that works.
Written by Lonnie Burke, Owner at Carver Gate Repair, serving San Antonio to The Garrison Standard since 2008. For other locations, we also provide Gate Repair services.
Pricing reflects the San Antonio market as of 2026. Carver Gate Repair offers free estimates – call (469) 530-2485.
What Our Customers Say
"Keypad and remotes set up fresh for the whole neighborhood. Done cleanly and quickly."
- Chris W."Straight answers on whether to repair or replace the operator. Repair was the right call."
- Wanda F."Gate hinge was bending under the weight. Welded a new bracket on and re-hung it. Solid now."
- Rudy A.