Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Los Angeles?
Gate installation in Los Angeles typically runs $2,800 – $8,500 for a standard residential swing or slide gate with motor, with most homeowners in neighborhoods like Sherman Oaks, Pasadena, and the Pacific Palisades landing around $4,200 – $5,800 for a complete setup. Custom iron work, hillside grading in the Hollywood Hills, or commercial-grade access control can push projects toward $12,000 – $18,000. We give every Carver Gate Repair customer a written price before any work starts, so the number you see is the number you pay.
Gate Installation Cost Breakdown (2026)
These ranges reflect what we’re quoting across Los Angeles County in 2026, from the flat lots of the San Fernando Valley to the sloped driveways of Silver Lake and Los Feliz. Prices include materials, labor, basic motor, and standard installation. Permits, electrical runs beyond 50 feet, and significant grade work are priced separately.
| Component | Typical Range |
|---|---|
| Basic steel swing gate (single, 12 – 14 ft) | $1,800 – $3,200 |
| Aluminum slide gate (16 – 20 ft) | $2,400 – $4,500 |
| Wrought iron or ornamental steel gate | $3,500 – $7,000 |
| Gate motor / operator (residential) | $800 – $2,200 |
| Gate motor / operator (commercial) | $2,200 – $5,500 |
| Access control (keypad, remote, intercom) | $400 – $1,800 |
| Loop detector or safety sensors | $250 – $650 |
| Concrete footing / post installation | $600 – $1,400 |
| Hillside grading or retaining (per project) | $1,500 – $5,000 |
| Los Angeles permit and inspection fees | $350 – $850 |
| Total typical residential installation | $2,800 – $8,500 |
| High-end custom / estate installation | $12,000 – $18,000+ |
What moves a project toward the top of the range? Steep driveways in the Hollywood Hills or Laurel Canyon where we need to engineer for grade, coastal exposure in Malibu or Palos Verdes that demands marine-grade powder coating, or historic district requirements in Angelino Heights where design review adds time and material cost. Flat lots in Burbank or Downey with standard access tend to land closer to the middle.
What Affects Gate Installation Pricing in Los Angeles
- Gate material and design. Steel costs less than wrought iron with custom scrollwork. Aluminum saves weight on slide systems but runs higher per pound. We see a lot of coastal requests for 316 stainless hardware in Santa Monica and Redondo Beach.
- Motor brand and capacity. A 1/2 horsepower LiftMaster swing operator handles most residential gates in the Valley. A 1 HP commercial-grade FAAC or BFT unit for a heavy iron gate in Hancock Park costs more but lasts longer under load. We work on nine brands, so we match the motor to the gate, not the other way around.
- Site conditions and access. Los Angeles basalt and clay soils in the foothills require deeper footings. Narrow driveways in Venice or the older parts of Koreatown limit equipment access and add labor hours.
- Electrical supply distance. Running 220V from a main panel to a rear gate in a Bel Air canyon can add $800 – $2,000 if trenching through mature landscaping is involved. Solar-charged systems avoid this but have their own cost structure.
- Permit complexity. Los Angeles Department of Building and Safety requires permits for most gate installations. Hillside areas trigger additional geotechnical review. We handle permit drawings and submission, but the timeline affects scheduling and sometimes labor rates.
- Access control features. A basic keypad is straightforward. Cellular-enabled intercoms with camera integration, common in newer builds around Playa Vista or the Arts District, add hardware and programming cost.
How to Save on Gate Installation Without Cutting Corners
The cheapest Gate Installation services are the ones you do once. We’ve been called to Los Angeles homes where a generalist contractor installed a motor too small for the gate weight, or skipped the limit switch calibration, and the system failed inside two years. Here’s how to control cost without sacrificing the work:
- Choose the right material for your exposure. Inland neighborhoods like Alhambra or Glendale don’t need marine-grade finishes. A quality powder-coated steel gate with proper maintenance lasts 15 – 20 years.
- Plan electrical during other work. If you’re already trenching for landscape lighting or a pool panel, run conduit for the gate motor at the same time. We coordinate with electricians on this regularly.
- Consider a swing gate over a slide gate. Swing systems require less track hardware and typically cost 20 – 30% less, assuming your driveway geometry allows it. We measure on-site to confirm.
- Bundle access control with installation. Adding a keypad or remote receiver during initial install costs less than retrofitting later. The wiring is already open.
- Get a written price before work starts. Every Carver Gate Repair estimate is itemized and fixed. No surprises mean no budget overruns. Call (469) 530-2485 for a free estimate – we measure, spec, and price on the spot.
FAQs – Gate Installation Cost
How much does a basic driveway gate cost installed in Los Angeles?
A standard 14-foot steel swing gate with motor, keypad, and installation typically costs $3,200 – $4,800 in the Los Angeles market. This covers flat lots in the San Fernando Valley, the Westside, and most of the basin. Hillside sites or custom designs run higher. Call (469) 530-2485 for an exact quote – estimates are free.
Is it cheaper to install a gate during new construction or as a retrofit?
New construction saves 15 – 25% on average. The footing can be poured with the driveway, electrical conduit runs before hardscaping goes in, and there’s no demolition of existing fencing or pillars. Retrofits in established neighborhoods like Los Feliz or Eagle Rock often require careful excavation around mature root systems and existing masonry.
Do I need a permit to install a gate in Los Angeles?
Yes, the Los Angeles Department of Building and Safety requires a permit for most gate installations, and an inspection for the electrical connection. Permit fees run $350 – $850 depending on valuation. We prepare the drawings and handle submission as part of our standard process – it’s not an upsell, it’s part of doing the job right.
How long does gate installation take?
Most residential installations finish in 1 – 3 days. Day one: excavation, footing pour, and gate hang. Day two: motor mount, limit switch calibration, and safety sensor alignment. Custom fabrication or hillside engineering can extend to 5 – 7 days. We give you a written schedule with the written price, so you know both before we start.
What’s included in Carver Gate Repair’s 365-Day Done Right Promise?
Every gate installation and repair we perform in Los Angeles carries a written, full-year guarantee. If anything fails due to our workmanship or material selection, we return and fix it at no charge. No argument, no re-diagnostic fee. The guarantee is in writing on every job, not a verbal promise. This is The Garrison Standard we’ve operated to since 2008.
Can you match my existing fence style?
We can. Our fabricators work from photos, existing samples, or architectural drawings. Matching Spanish Colonial ironwork in Hancock Park, mid-century horizontal slat designs in the Eichler neighborhoods, or contemporary styles in Venice – we’ve done it. Custom matching adds 10 – 20% to material cost but preserves property aesthetic and often HOA compliance.
Ready for Your Los Angeles Gate Installation Estimate?
We’ve installed gates across Los Angeles from the Pacific Palisades to Pasadena, and every job starts the same way: a background-checked, uniformed technician arrives in the window we promised, measures your site, and delivers a written price before any work begins. No voicemail. No call-back queues. No moving numbers.
Call (469) 530-2485 now. A live person answers, 24 hours a day, every day of the year. We’ll schedule your free estimate and walk you through material options, motor sizing for your specific gate weight, and what your Los Angeles site conditions mean for timeline and cost.
Pricing reflects the Los Angeles market as of 2026. Carver Gate Repair offers free estimates – call (469) 530-2485.
Written by Lonnie Burke, Owner at Carver Gate Repair, serving Los Angeles to The Garrison Standard since 2008.
What Our Customers Say
"Keypad and remotes set up fresh for the whole neighborhood. Done cleanly and quickly."
- Chris W."Straight answers on whether to repair or replace the operator. Repair was the right call."
- Wanda F."Gate hinge was bending under the weight. Welded a new bracket on and re-hung it. Solid now."
- Rudy A.