Ghost Controls Gate Repair Nationwide

Ghost Controls Gate Repair in Los Angeles: What to Know First

We provide independent Ghost Controls gate repair in Los Angeles, and most calls are completed same-day or next-day. A typical Ghost Controls swing operator repair runs $240 – $480, and we give you a written price before any work starts. This page is for Los Angeles homeowners whose Ghost Controls gate has stopped mid-cycle, started beeping error codes, or simply won’t respond to the remote. We work on the full Ghost Controls lineup, from the TSS1XP heavy-duty single swing to the DSS1 dual swing and the ABBT battery box systems. Call us at (469) 530-2485 for a free estimate.

Call (469) 530-2485

How Ghost Controls Products Fail – and How We Fix Them

• TSS1XP and TDS2 heavy-duty operators – stripped limit switch gears. These units use a plastic limit switch gear train that cracks under the load of a sagging Los Angeles gate. Once the gear slips, the operator can’t find its open or closed position and runs until the safety kicks in. We replace the gear with an OEM or machined brass equivalent, then realign the gate so the new gear isn’t fighting the same load.
• DSS1 dual swing – control board failure after power events. The DSS1 control board is sensitive to voltage spikes, and Los Angeles sees plenty of those during Santa Ana wind season when grid switching happens. The board throws a solid red light or no light at all. We test the board at component level where possible, replace with a new Ghost Controls board if it’s fried, and install a surge protector on the low-voltage side to prevent the next event.
• ABBT battery box systems – sulfated batteries from heat cycling. The ABBT relies on two 12V batteries in a vented box, and Los Angeles summer heat cooks them in two to three years instead of the rated five. The gate slows down, then stops entirely, and the owner assumes the motor is dead. We load-test each battery separately, replace with deep-cycle AGM units rated for high-temp operation, and check the solar panel or transformer charging circuit while we’re in there.
• TSS1XP with tube arm – twisted arm from gate bind. The tube arm on the TSS1XP is aluminum, light and fast, but it twists if the gate hinge settles or the post leans. We see this in the hillside areas around Los Feliz and Silver Lake where gates are hung on retaining walls that move. We straighten or replace the arm, but more importantly we diagnose why it twisted – hinge, post, or track – and fix that first so it doesn’t happen again.
• All Ghost Controls operators – ghost voltage on the loop detector circuit. The loop detector input on Ghost Controls boards is finicky about residual voltage from old loops or spliced wire running through damp conduit. The gate opens fine but won’t close, or reverses for no visible reason. We trace the loop with a scope, replace corroded splices, and sometimes run new direct-burial cable where the original installer used the wrong gauge for a Los Angeles property with a long driveway.

Our Ghost Controls Gate Repair Process

1. 1
   Call intake with a live person. Our phones are answered 24 hours a day. We ask for the model number on the operator cover, the symptom, and how the gate is mounted – this lets us pull the right parts before dispatch.
2. 2
   On-site diagnosis. The technician arrives in a marked vehicle, uniformed, and checks the operator, the gate mechanicals, and the power supply as one system. Ghost Controls problems are often a symptom, not the root cause.
3. 3
   Written price before work. We itemize parts and labor. If an OEM Ghost Controls board is backordered, we explain the aftermarket option and the trade-off. No work starts until you approve the number in writing.
4. 4
   Repair and load test. We fix what’s broken, then cycle the gate fifty times under load, test every safety input, and verify the auto-close timer if you use one.
5. 5
   Cleanup and written guarantee. We leave the site clean. You get a 365-Day Done Right Promise in writing, covering parts and labor. If the same problem returns inside a year, we come back free.

What Ghost Controls Gate Repair Costs in Los Angeles

What moves the price: gate size and weight, whether the post or hinge needs work, and whether we can use an in-stock part or need to order from Ghost Controls directly. We don’t guess. We diagnose, then quote. Estimates are free.

Why Los Angeles Homeowners Call Carver Gate Repair for Ghost Controls Work

We’ve worked on Ghost Controls operators in Los Angeles long enough to know which parts fail twice if you don’t fix what caused the failure. Our technicians are trained on nine brands, including LiftMaster, Mighty Mule, and DoorKing, so when a Ghost Controls system is beyond repair we can recommend a replacement that fits your gate without selling you what we happen to stock. The Garrison Standard means background-checked, uniformed techs; a written price before any work starts; and a full-year guarantee on every repair. Lonnie Burke runs this shop the way he learned at Los Angeles Trade-Technical College – show up squared away, fix what’s broken, and don’t make the customer ask twice. If the repair fails inside the guarantee window, we come back free. No argument.

FAQs