Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLinear Gate Installation in Los Angeles: What to Know First
We install Linear gate operators and full gate systems across Los Angeles as an independent Linear service provider, with most residential jobs measured, quoted, and scheduled within a week. Every installation starts with a free on-site estimate, a written price you approve before we touch a tool, and a 365-Day Done Right Promise backed in writing. If you’re replacing a failed Linear operator or putting in a new driveway or pedestrian gate from scratch, we’ll match the right Linear model to your gate’s weight, cycle count, and how Los Angeles coastal moisture or Valley heat affects the hardware. Call us at (469) 530-2485 to book your free estimate.
How Linear Products Fail – and How We Fix Them
- Linear HSLG series sliding operators seize in the gearbox after three to five years in Los Angeles, especially in beach-adjacent neighborhoods like Venice and San Pedro where salt air gets past the housing seals. The factory grease breaks down and the worm gear scores the housing. We pull the operator, assess whether the gearbox is salvageable, and if not, source an OEM replacement or a quality aftermarket equivalent with comparable torque specs.
- Linear SW33 and SW44 swing arms crack at the articulating joint on heavy wrought-iron gates common in Hancock Park and Los Feliz. The cast aluminum elbow fatigues from the gate’s momentum in wind. We don’t just swap the arm; we verify the gate is properly balanced and recommend steel-arm upgrades when the gate weight is near the operator’s limit.
- Linear PRO Access control boards fail after power surges during L.A.’s Santa Ana wind season, when grid fluctuations spike. The MOVs on older boards sometimes don’t clamp fast enough. We install surge-protected loops on new installations and carry replacement PRO Access boards with updated firmware that handles voltage spikes better than the original revision.
- Linear LA500 and LA950 battery backup systems degrade in Valley heat, particularly in Van Nuys and Northridge where summer garage and gate equipment temperatures exceed 110°F. The sealed lead-acid batteries dry out in eighteen months, not the three years Linear rates them for. We factor this into our installation specs and specify AGM batteries with higher heat tolerance, or we hardwire solar trickle chargers on rural-exposure properties.
- Linear loop detectors false-trigger on rebar-heavy driveways in post-war slabs across the San Fernando Valley. The inductive loop sees the steel mesh and opens the gate uncommanded. We relocate loops to clean asphalt cuts, switch to Linear’s micro-loop profile for tighter detection fields, or recommend photoeye retrofitting when the slab won’t cooperate.
Our Linear Gate Installation Process
- 1
Site measure and load calculation. We weigh your gate or calculate its moment arm, count daily cycles, and note grade, wind exposure, and power source location. Linear’s spec sheets are conservative; we size up when a gate runs near a model’s limit.
- 2
Written estimate with model recommendation. You get a fixed price for the complete job – operator, mounting hardware, safety edges, loop or photoeyes, power run if needed, and labor. No line item moves once you sign.
- 3
Parts procurement: OEM or qualified aftermarket. We stock common Linear operators in Los Angeles, but if your job needs a PRO Access 2.0 or a specific HSLG variant, we order factory-direct or source from our verified aftermarket supplier. We tell you which we’re using and why.
- 4
Install to Linear’s torque and safety specs, plus our own. We set limit switches with a manual override test, verify entrapment protection with a 2×4 block test on every cycle, and program remote access only after you’ve tested it yourself.
- 5
Cleanup, documentation, and guarantee activation. You get the operator manual, your remote programming sheet, and a written copy of the 365-Day Done Right Promise. If anything fails inside that year, we come back free. No argument.
What Linear Gate Installation Costs in Los Angeles
| Job Type | Typical Range | What Moves the Price |
|---|---|---|
| Single swing gate, Linear LA500 operator, basic hardware | $2,800 – $4,200 | Gate weight, wood vs. steel, existing power vs. new run |
| Dual swing gate, Linear LA950 or comparable, safety package | $4,500 – $6,800 | Gate width, column rebuild, loop detector vs. photoeyes |
| Sliding gate, Linear HSLG-500 or HSLG-1000 | $3,400 – $5,600 | Track condition, cantilever vs. overhead rail, travel distance |
| Pedestrian gate with Linear PRO Access control | $1,800 – $3,200 | Keypad vs. card reader, maglock vs. strike, intercom add-on |
| Operator-only replacement, existing gate and hardware good | $1,400 – $2,600 | Retrofit bracket fabrication, old operator disposal, code updates |
These are real ranges from our Los Angeles jobs in the last eighteen months. Your exact price comes after we measure. Call (469) 530-2485 for a free estimate – the number we write down is the number on the invoice.
Why Los Angeles Homeowners Call Carver Gate Repair for Linear Work
We’ve been doing this in Los Angeles since 2008, and we’ve learned that gate work goes wrong when the crew treats it as a side job. We’re gate specialists. Our techs train on nine brands – Linear, LiftMaster, Mighty Mule, Ghost Controls, DoorKing, and four others – so when your Linear PRO Access needs to integrate with an existing DoorKing keypad, we don’t guess. Every technician is background-checked, uniformed, and arrives in a marked vehicle. Phones get answered by a live person, 24 hours a day, including Christmas. The Garrison Standard means we show up squared away, fix what’s broken, and don’t make the customer ask twice. The 365-Day Done Right Promise is in writing on every job, and if we miss something, the second visit is free. No charge, no argument.
FAQs
No. Your gate manufacturer’s warranty covers defects in the gate itself; the operator is a separate component. We install Linear operators to the gate manufacturer’s load specifications, and our 365-Day Done Right Promise covers our workmanship independently. If your gate is still under builder warranty, we document our install method so there’s no dispute about cause. Call (469) 530-2485 if you need us to coordinate with your builder.
Most residential Linear installations finish in one day. A straightforward single-swing operator swap on existing hardware takes four to six hours. A full sliding gate with track work, operator mount, and loop detector install can run into a second day if we’re pouring concrete or welding steel posts. We tell you the schedule when we deliver the written estimate, not when the crew shows up.
Replace it if the gearbox is cracked, the control board is obsolete, or repair parts would cost more than 60% of a new unit. Repair makes sense for limit switch failures, sensor replacements, or arm adjustments on operators less than eight years old. We diagnose first, then give you both numbers – repair and replace – so you decide from facts, not pressure.
We stock LA500, LA950, and HSLG operators, common remote receivers, and safety edge kits at our Los Angeles warehouse. PRO Access 2.0 boards and specialty arms we order factory-direct with a three- to five-day lead time. We don’t promise same-day on parts we don’t have, and we don’t substitute without telling you.
We come back and fix it free. The 365-Day Done Right Promise covers every installation we complete – parts, labor, and any adjustments. If the failure is a defective Linear component, we handle the manufacturer warranty claim ourselves; you don’t wait on hold with Linear. Call (469) 530-2485 and a live person will schedule the return visit.
Written by Lonnie Burke, Owner, Carver Gate Repair at Carver Gate Repair, serving Los Angeles and nearby areas.